Knex PSP Dock
Intro: Knex PSP Dock
Here's a dock I made for my PSP that can either just be sat down on a flat surface or it can be hung from the side of a bed. Let's get started!
STEP 1: The Back
This is the back of the dock. It uses a lot of pieces so that it's strong and smooth.
1: Make 16 of these
2: Connect all of the yellow connectors onto a red/green rod like in the picture.
3: Add a red/green rod to the light grey connectors.
1: Make 16 of these
2: Connect all of the yellow connectors onto a red/green rod like in the picture.
3: Add a red/green rod to the light grey connectors.
STEP 2: The Bottom
This is the bottom of the dock that holds the PSP.
1: Make 16 of these
2: Connect all the red connectors with a red/green rod.
1: Make 16 of these
2: Connect all the red connectors with a red/green rod.
STEP 3: The Base
This is what sits on whatever flat surface you put the PSP Dock on.
1: Make this
2: Make a second one
3: Attach a red/green rod to the yellow connector on one of them.
1: Make this
2: Make a second one
3: Attach a red/green rod to the yellow connector on one of them.
STEP 4: Side Charger Wire Holder
This is a part that is added to the side of the PSP Dock that keeps the charger wire in place so that you can charge your PSP on the dock.
1: Make these 3 parts.
2: Connect the green connectors and the blue rod as shown in the picture.
1: Make these 3 parts.
2: Connect the green connectors and the blue rod as shown in the picture.
STEP 5: Sides
These pieces stop the PSP from falling out of the dock if it is tilted sideways.
1: Make this part.
2: Put 4 blue spacers on a blue rod.
3: Connect the two parts that you have made.
4: Make these two parts.
5: Add them to the construction.
6: Make a mirror version of what you just made in the previous 5 steps.
1: Make this part.
2: Put 4 blue spacers on a blue rod.
3: Connect the two parts that you have made.
4: Make these two parts.
5: Add them to the construction.
6: Make a mirror version of what you just made in the previous 5 steps.
STEP 6: Assembly
Now we're going to put it together.
1: Connect the bottom to one of the sides of the base.
2: Connect the other side of the base to what you have.
3: Add the back of the base to the rest.
4: Connect one of the sides to the white connector.
5: Connect the other side to the other white connector.
6: Connect the orange connector/blue end cap construction to the red/green rod like in the picture.
7: Connect the blue rod attached to the 3 green connectors to the green connector on the dock.
8: The finished dock!
1: Connect the bottom to one of the sides of the base.
2: Connect the other side of the base to what you have.
3: Add the back of the base to the rest.
4: Connect one of the sides to the white connector.
5: Connect the other side to the other white connector.
6: Connect the orange connector/blue end cap construction to the red/green rod like in the picture.
7: Connect the blue rod attached to the 3 green connectors to the green connector on the dock.
8: The finished dock!
STEP 7: Finishing Touches
Just some finishing touches to the dock including and optional attachment so you can hang it from the side of a bed.
1: Add the wire from the charger like in the picture.
2: This is how the plug goes into the PSP when it's being charged on the dock.
The Optional Attachment
3: Make these pieces and get two red/green rods.
4: Connect the two green rods on one of the pieces like in the picture.
5: Connect the other piece on only the orange connector side.
6: Slide the red/green rod through the light grey connectors' holes and connect the other red connector onto the rod.
7: Slide the orange connector part in between the side of the bed and the mattress.
8: Finished!
1: Add the wire from the charger like in the picture.
2: This is how the plug goes into the PSP when it's being charged on the dock.
The Optional Attachment
3: Make these pieces and get two red/green rods.
4: Connect the two green rods on one of the pieces like in the picture.
5: Connect the other piece on only the orange connector side.
6: Slide the red/green rod through the light grey connectors' holes and connect the other red connector onto the rod.
7: Slide the orange connector part in between the side of the bed and the mattress.
8: Finished!
14 Comments
sonicmule12 13 years ago
bbot2500 13 years ago
asdfda3432 13 years ago
danbaha 13 years ago
wout smeets 13 years ago
knektek 14 years ago
hi111 14 years ago
Made mine in 10 min. and it works great (small/minimal Mods)
wehe-tehe 14 years ago
tubanator-2.0 14 years ago
J Moneyman 14 years ago
J Moneyman 14 years ago
J Moneyman 14 years ago
Jesus. 14 years ago
Bartboy 14 years ago