Knex Longbow SR-L Crossbow

5,879

18

193

Introduction: Knex Longbow SR-L Crossbow

About: I first joined this site in 2008 when I was a bored ignorant teenager with a lot of free time on my hands. Now as of 2019, I’m 23 and in graduate school so I’m permanently inactive here. If you still want to k…

ok, ok, I admit i have gotten the gun names from video games. now here goes the intro:

It all started in 06 and a half. A basic knex cannon, block trigger, simple ram, and an unusual taste of ammo.

Today, we have gone so far. And this proves it. Introducing the Knex Longbow SR-L crossbow. simple to make, piece-efficient, and pretty decent overall. It is also the first crossbow to have a bipod and scope (correct me if i am wrong)..................

PROS

-true-trigger
-not flimsy
-60-80 foot range
-foldable bipod
-rubberband stays on the bow no matter what (unless you take it off)

CONS

-not the best stock
-horizontal bow could be longer

Version history

1.4- this was a concept spin- off of my SPEC-9 sniper rifle
1.6- added an extra layer on the bottom of the crossbow and improved bipod
1.8- replaced stock with a better one that features a sight

this crossbow is very similar to my sniper. if you want to choose, it depends on what you want. If you want a solid, sturdy gun, build this gun. If you want more range, build the sniper.

overall, this is a good upgrade for my sniper, i would recommend you build this gun...............

Step 1: Handle

follow the pictures.

1. build this

2. another view

3. yet another view

4. build the bipod holder (not optional)

5. assemble (add parts)

Step 2: Stock

really, all you need is one picture

Step 3: The Barrel

again, you just need one picture

Step 4: The Horizontal Bow

again, one picture is needed. add spacers everywhere, i didnt because i ran out

Step 5: Bipod (optional)

build the bipod. this part is completely optional, but replace the green rod seen with a gray rod

Step 6: Assemble

ok, here is the step that makes it all work.............

1.attach bipod (optional)

2. attach horizontal bow to barrel

3. attach stock to handle

4. connect handle to barrel

Step 7: Ammo

the ammo is the same as my sniper, just make

Step 8: Loading and Firing

to load, pull the rubberband band back to the wheel and turn it back.

then, put ammo in the barrel, aim and pull the trigger

Be the First to Share

    Recommendations

    • Pumpkin Challenge

      Pumpkin Challenge
    • Bikes Challenge

      Bikes Challenge
    • Remix Contest

      Remix Contest

    193 Discussions

    0
    bboy321321
    bboy321321

    7 years ago on Introduction

    i love it because it looks good and doesn't use a lot of pieces.

    0
    PotatoCoffee
    PotatoCoffee

    8 years ago on Introduction

    Right. Nail my other comment down there. Excluding the age, the lack of peices and the fact that I am nowhere near a Knexpert, I can't help LOL'ing at the first version. Please tell me if you think this is hating and I will remove it.

    0
    wertywaster
    wertywaster

    10 years ago on Introduction

    I dont like da handle though. AND it shoots about seven feet, i dont know if it even shoots longer

    0
    DJ Radio
    DJ Radio

    Reply 10 years ago on Introduction

    Fix it. You built it wrong. Mine shot around 50.

    0
    DJ Radio
    DJ Radio

    Reply 10 years ago on Introduction

    If you did it would shoot 50 feet.

    0
    wertywaster
    wertywaster

    Reply 10 years ago on Introduction

    WELL IT DID NOT SHOOT 50 FEET, ITS JUST A STUPID 1FOOT SHOOTING CROSS BOW!!!!!

    0
    Eion
    Eion

    9 years ago on Introduction

    Nice crossbow I made the other one but the rubber band kept getting stuck so I am making this one