MP5K

Introduction: MP5K

About: I like knexing, if you haven't noticed. Check out my photobucket account!

Here is my knex MP5K . It's my entry for the MW2 contest. AND IT WON!
Its a good replica with these features:

*Shoots Dark Gray Connectors
*Angled Removable mags (normal or high cap)
*Realistic
*Good sights
*Fore-Grip
*Optional upper receiver with rails (Not Posted - Just replace 3rd and 5th layers with whites and yellows)
*Good for a replica or side arm

Review: https://www.instructables.com/community/Knex-MP5K-review/
PLEASE COMMENT RATE AND SUBSCRIBE!!!

Step 1: Build a Whole Lot of Stuff

Build a whole lot of stuff

Step 2: Assemble the Gun

Assemble the Gun

Step 3: Magazines

Normal on left, High Cap on right!

Step 4: Loading the Mag Into the Gun Properly

Insert the MAGAZINE (not clip) into the gun correctly for it to shoot right!

Step 5: Mods

Here are mods made to the gun that have been made by me, or you guys.
--------------------------------------------
Mag release, with a few other attachments. Made by: osi
https://www.instructables.com/id/Mag-release-for-shadowninja31s-MP5k-The-Instru/

Step 6: Your Guns

Here are some of your versions of this gun!
Pic 1 - John Copper's version
Pic 2 - Ymerej88's version
Pic 3 - knex gun builder's version
Pic 4 - osi's version. He added a mag release that works!
Pic 5 - Dr MonkeyMan's version

Be the First to Share

    Recommendations

    • Make it Glow Contest

      Make it Glow Contest
    • First Time Author Contest

      First Time Author Contest
    • Anything Goes Contest

      Anything Goes Contest

    277 Discussions

    0
    Dr MonkeyMan
    Dr MonkeyMan

    7 years ago on Introduction

    Hey shadowninja im new and i made some mods for your gun and i was wondering if i could post them

    0
    shadowninja31
    shadowninja31

    Reply 7 years ago on Introduction

    I'll need you to send some pictures and info or something but sure!

    0
    2000smartkid
    2000smartkid

    8 years ago on Introduction

    (this comment is only for people who want to accept this challenge) If you can, I want to see if anyone can make a knex version of the Nerf Vortex Nitron. I will leave some pictures of it in my profile. If you want to try this, comment below this comment. If you think you have succeeded after making it, comment below the acception of the challenge.

    0
    2000smartkid
    2000smartkid

    8 years ago on Introduction

    Hey, I modded both mags a little bit, because for some reason, the ram would knock the mag out of the gun. So I added some parts and cut some parts to fix the problem. I will try to upload some pics that show what I did. :)

    0
    shadowninja31
    shadowninja31

    Reply 8 years ago on Introduction

    Interesting. Yeah that would be helpful I'd like to see what went wrong.

    0
    2000smartkid
    2000smartkid

    Reply 8 years ago on Introduction

    Actually, I just made it again (because I had taken it apart) and I found out why the ram would knock the mag out of the gun. It was because the mag wasn't in the gun right. So I put it in the right way, and the ram doesn't knock it out.

    0
    james4
    james4

    9 years ago on Introduction

    5 female ball joint connecters.............. THIS IS MADNESS

    0
    eLeMeNtLtd.
    eLeMeNtLtd.

    8 years ago on Introduction

    Shadowninja31, may i use the mag removal system for my gun? plz reply as fast as possible.

    0
    rlaxrlax
    rlaxrlax

    8 years ago on Introduction

    just some advice on the rubber band try using small ones for the trigger and size 64s for the firing pin