Red Signal Crossing by Karam

ان المشروع مثل اشارة المرور بدون الون الاخضر مع عداد يعد

الى العشرة واذا تحرك شيئ امامها سوف تزمر و تبقا اشارة

امرور الحمراء مضيئة,انها تحمي اذا دخل شخص غريب الى

البيت او الفندق او المكتب او اي مكان اخر , او تستخدم الى

تعليم الاطفال كيف تعمل اشارة المرور .

Step 1:

PARTS:

1:SEVEN SEGMENTS.

2:Ultrasonic Ranging Module HC - SR04.

3:buzzer.

4:TWO RED (LEDS) .

5:WIRES.

6: TWO RESISTANC(RED,RED,BLACK,GOLD)220 OHM, And one Resistanc ( green, blue, brown, gold)561 OHM.

Step 2: Code

int trigPin = 13;
int echoPin = 12;
int led = 7;
int buzzer = 1;
//#define led2 11
int Sig1_G=11;
int Sig1_R =10;

int a = 2; //For displaying segment "a"
int b = 3; //For displaying segment "b"
int c = 4; //For displaying segment "c"
int d = 5; //For displaying segment "d"
int e = 6; //For displaying segment "e"
int f = 8; //For displaying segment "f"
int g = 9; //For displaying segment "g"
int i;
void setup() {
pinMode(a, OUTPUT); //A
pinMode(b, OUTPUT); //B
pinMode(c, OUTPUT); //C
pinMode(d, OUTPUT); //D
pinMode(e, OUTPUT); //E
pinMode(f, OUTPUT); //F
pinMode(g, OUTPUT); //G

pinMode(Sig1_G,OUTPUT);
pinMode(Sig1_R,OUTPUT);
pinMode(trigPin, OUTPUT);
pinMode(echoPin, INPUT);
pinMode(led, OUTPUT);
pinMode(buzzer,OUTPUT);
Serial.begin(9600);
}
void displayDigit(int digit)
{


//Conditions for displaying segment a
if(digit!=1 && digit != 4)
digitalWrite(a,HIGH);

//Conditions for displaying segment b
if(digit != 5 && digit != 6)
digitalWrite(b,HIGH);

//Conditions for displaying segment c
if(digit !=2)
digitalWrite(c,HIGH);

//Conditions for displaying segment d
if(digit != 1 && digit !=4 && digit !=7)
digitalWrite(d,HIGH);

//Conditions for displaying segment e
if(digit == 2 || digit ==6 || digit == 8 || digit==0)
digitalWrite(e,HIGH);

//Conditions for displaying segment f
if(digit != 1 && digit !=2 && digit!=3 && digit !=7)
digitalWrite(f,HIGH);
if (digit!=0 && digit!=1 && digit !=7)
digitalWrite(g,HIGH);
//digitalWrite(Sig1_G,HIGH);


}
void crossRedsignal()
{
digitalWrite(buzzer,LOW);
long duration, distance;
digitalWrite(trigPin, LOW); // Added this line
delayMicroseconds(2); // Added this line
digitalWrite(trigPin, HIGH);
// delayMicroseconds(1000); - Removed this line
delayMicroseconds(10); // Added this line
digitalWrite(trigPin, LOW);
duration = pulseIn(echoPin, HIGH);
distance = (duration/2) / 29.1;
if (distance < 100) { // This is where the LED On/Off happens
digitalWrite(led,HIGH); // When the Red condition is met, the Green LED should turn off
// digitalWrite(led2,LOW);
}
else {
digitalWrite(led,LOW);
//digitalWrite(led2,HIGH);
}
if (distance >= 200 || distance <= 0){
Serial.println("Out of range");
}
else {
Serial.print(distance);
Serial.println(" cm");
// digitalWrite(led,HIGH);
}
delay(500);
}

void turnOff()
{
digitalWrite(a,LOW);
digitalWrite(b,LOW);
digitalWrite(c,LOW);
digitalWrite(d,LOW);
digitalWrite(e,LOW);
digitalWrite(f,LOW);
digitalWrite(g,LOW);


// delay(2000);
}

void loop() {
for( i=0;i<10;i++)
{
displayDigit(i);
crossRedsignal();
digitalWrite(Sig1_G,HIGH);
digitalWrite(Sig1_R,HIGH);
delay(1000);

turnOff();

}
if ( i = 10) {digitalWrite(Sig1_G,LOW);digitalWrite(Sig1_R,LOW); delay(1000);}
//crossRedsignal();
}

Step 3: