Introduction: Star Wars Rey Costume With Props
This is a Star Wars Rey costume I made for my daughter, complete with a bunch of accessories.
The techniques I used to make this could easily be scaled for a person of any size.
Step 1: Materials
I raided all of my fabric bins and pulled out anything that might be useful.
I'm a hoarder when it comes to fabric and supplies for making stuff, so a lot of what I needed I already had on hand. Here's a list of most of the materials used for this project:
- A "Onesie"-style toddler body suit for the shirt
- A couple small pieces of an old gray sheet became Rey's pants
- Fake leather from an old suitcase became all the various leathery bits
- Brown corduroy was used for Rey's satchel/hip bag
- Natural-colored cotton was used for her shoulder sashes and arm wraps (this was purchased)
- Furry fabric and old sneakers were used to make the boots (purchased)
- A wooden dowel and miscellaneous bits of stuff were used for Rey's "Quarterstaff"
- Instant coffee, bags of black tea, and fabric dye for altering colors of fabric
And the tools I used:
- Sewing machine
- Serger - I survived for years without one, but just picked up one at Walmart. It works well and was less than $200.
- Glue gun
- Cutting mat and all the typical crafting tools (hobby knife, scissors, etc.)
Step 2: Dying Fabric
The natural color of the cotton I had purchased for Rey's shoulder sashes and arm wraps wasn't quite the color I was after. I wanted it to be more greyish-ish.
I played around with various dyeing techniques to see what I could come up with. After some experimenting, this is what I ended up doing to about two square yards of cotton:
- Washed the fabric on hot cycle a couple of times to shrink and loosen up the fibers
- Mixed about 3 table spoons of Pearl Grey Rit dye into 2 gallons of very hot (but not boiling) water in a bucket
- Stirred the fabric around in this for about 5 minutes, and then rinsed it under cold water until the water ran clear
- Mixed about 1 cup of instant coffee into 2 gallons of very hot water in another bucket
- Stirred the now-lightly-grey fabric around in the coffee and rinsed, just as was done with the grey dye
- Dried the fabric in the dryer and then ironed it flat
Step 3: Shoulder Sashes
For the shoulder sashes, I wanted them to be somewhat permanently wrinkled. Otherwise we'd be fussing with trying to make the wrinkles look right whenever my daughter wears this costume.
The details of the process I used are outlined in the photo notes.
Step 4: Shirt
The onesie I used for this was stark white, and I wanted it to be just slightly greyish.
To achieve this color, I dyed the shirt in one gallon of hot water with one table spoon of grey dye. I stirred it around for a few minutes and then rinsed it thoroughly. This created a very subtle off-white color.
The bottom snaps of the onesie were trimmed off to make it into a plain shirt.
Step 5: Pants
I happened to have an old sheet that was the exact color I wanted for Rey's pants.
Using a pair of my daughter's pajamas I made a rough pattern to use to make these pants. See notes in photos for details.
Step 6: Hip Bag/satchel
I made a hip bag to look like Rey's out of some old corduroy with various bits of things added on for detail.
Step 7: Belt
The belt was made with fake leather, hot glue, and some cotton string.
Step 8: Cuff Bracelet
A simple cuff bracelet was made with fake leather.
Step 9: Arm Wraps
The arm wraps were made from strips of cotton that were 1 1/4" wide by about 60" long. These were serged along the edges to keep them from fraying.
When worn, these are wrapped in place and then held on with safety pins.
Step 10: Quarterstaff
I wanted to make a very simple staff that just evoked the style of Rey's quarterstaff.
It actually turned out better than I had hoped for!
How this was done is outlined with lots of notes in the photos here in this step, as well as the next.
Step 11: Finish Details for Rey's Quarterstaff
The quarterstaff was painted and various colors were added to create depth and a bit of weathering.
Step 12: Boots
The boots were made by simply hot gluing pieces of wooly fabric onto an old pair of thrift store sneakers. I sent them through the wash first, however. Who knows what nasty foot germs the previous kid had!
Little details were added with fake leather and pieces of yarn.
Step 13: Done!
This Rey costume is not "movie-accurate" or anything, but I was happy with the ratio of details I was able to include for the time and effort I put in.
Thank you for taking a look. I hope this will help you with a similar project!
As always, thoughts and feedback are enjoyed and appreciated :)