Introduction: Trauts' Side-Arm - TMG
The TMG or "Trauts' Modified Glock" is a 9-shot handle fed pistol. The reason it's a modified glock is because I like making replicas, but this one was made primarily for function over looks. It still looks good, but functions better. A large amount of this gun is just a big mod of the TDS by TheDunkis. Credit goes to him for the barrel and magazine design.
Pros...
- 9-shot
- Compact/sturdy
- Comfortable
- Jam-Free
- Light trigger
Cons...
- Low range
Pros...
- 9-shot
- Compact/sturdy
- Comfortable
- Jam-Free
- Light trigger
Cons...
- Low range
- Now with movie *
Attachments
Step 1: Handle
Pic 1 - Build this
Pic 2 - Tilt it till it looks like this
Pic 3 - Attach Black Y connectors as shown
Pic 4 - Add green rods to the top
Pic 5 - Build the comfort pieces
Pic 6 and 7 - Slide them on (to hold them on just loosely wrap a rubber band around them and the handle. If it's too tight it may jam the magazine).
Pic 2 - Tilt it till it looks like this
Pic 3 - Attach Black Y connectors as shown
Pic 4 - Add green rods to the top
Pic 5 - Build the comfort pieces
Pic 6 and 7 - Slide them on (to hold them on just loosely wrap a rubber band around them and the handle. If it's too tight it may jam the magazine).
Step 2: Top Piece
Pic 1 - Built it
Step 3: Ram and Ram Stopper
Note : requires weakened tan clip.
Pic 1 - Build this
Pic 2 - Slide it together
Pic 1 - Build this
Pic 2 - Slide it together
Step 4: Trigger
Pic 1 - Build it
Step 5: Barrel
Pic 1 - Build these parts
Pic 2 - Slide on the parts
Pic 3 - Close it up with the other side
Pic 4 - Take your "Top Piece"
Pic 5 - Clip it on top
Pic 2 - Slide on the parts
Pic 3 - Close it up with the other side
Pic 4 - Take your "Top Piece"
Pic 5 - Clip it on top
Step 6: Assembly
Pic 1 - Ram and ram stop ready to go on
Pic 2 - Line it up
Pic 3 - Clip it on
Pic 4 - Trigger ready to go on
Pic 5 - Clip it on
Pic 6 - Handle goes on last
Pic 2 - Line it up
Pic 3 - Clip it on
Pic 4 - Trigger ready to go on
Pic 5 - Clip it on
Pic 6 - Handle goes on last
Step 7: Rubber Bands, Mag Pusher, Loading and Firing
Pic 1 - Rubber bands and make the mag pusher
Pic 2 - Trigger rubber band
Pic 3 - Mag push rubber band
Pic 4 - Firing pin rubber band
********
*Optional*
Very similar to TheDunkis' mag push. Just as an option.
Pic 5 - Make it
Pic 6 - Put the pusher in it
Pic 7 - Clip it in for use
********
Pic 8 - Bullets
Pic 9 - Load them in like this
Pic 2 - Trigger rubber band
Pic 3 - Mag push rubber band
Pic 4 - Firing pin rubber band
********
*Optional*
Very similar to TheDunkis' mag push. Just as an option.
Pic 5 - Make it
Pic 6 - Put the pusher in it
Pic 7 - Clip it in for use
********
Pic 8 - Bullets
Pic 9 - Load them in like this
Step 8: Have Fun!
1 - load it up
2 - Put the mag pusher in
3 - Pull back the ram all the way, release, then pull the trigger
Repeat step 3 until no rounds remain in the handle, then follow steps 1 to 2 and repeat this process.
2 - Put the mag pusher in
3 - Pull back the ram all the way, release, then pull the trigger
Repeat step 3 until no rounds remain in the handle, then follow steps 1 to 2 and repeat this process.