Wood & Industrial Pipe Hall Tree DIY




Introduction: Wood & Industrial Pipe Hall Tree DIY

About: Obsessive DIYer

Step 1: Gather Materials

  • 4x Wooden Crates (Mine were from Michaels)
  • 3x 8″ by 17″ cut pieces of wood – I believe I used Common Board from Home Depot
  • 1x 8″ by 36″ cut piece of wood from same board as above.
  • 4x 3/4″ Floor Flange
  • 2x 30″ Industrial Pipe
  • 2x 36″ Industrial Pipe
  • 2 3/4″ Coupling
  • 4 Hooks
  • Varathane Wood Stain in Walnut
  • Varathane Satin Polyurethane Spray
  • Rags to Stain With
  • Variety Pack of Screws
  • Drill
  • Screwdriver
  • Sandpaper
  • Goo Gone
  • Wooden Paint Stir Stick (to fix the uneven crates; free at Home Depot)

Step 2: Prep

Once you’ve gathered all of your supplies, you will need to prep all of the materials and stain the wood. I sanded down all of the wood boards and crates as must as possible. The crates were fairly low quality so they needed a decent amount of sanding due to their rough nature. I then used Goo Gone to remove all of the price stickers from the industrial pipes and wiped them down.

Step 3: Stain

Use a rag (I used microfiber clothes) to stain all sides of the wooden boards and crates. I decided to leave some bottoms and backs of the crates unstained because they weren’t going to be seen due to their orientation. Follow the stain’s instructions for dry time. Then use the polyurethane spray to apply 2 coats (following instructions) to seal in the stain.

Step 4: Assemble Crates

After sufficient amount of dry time I was able to assemble the structure. Start with the wood crates at the bottom. Securely screw each 8″x17″ board to the bottom crates (one on each end and one in the middle). Then make sure you screw the bottom two crates together horizontally. After you have finished the bottom set you may start to attach the top crates. My crates were uneven so I added pieces of a Wood Paint Stir Stick to even it out (see pictures below). I then screwed these crates to the bottom crates to complete my crate structure.

Step 5: Assemble Industrial Pipe

I fully screwed together all industrial pipe parts and screwed in two bottom flanges to the two outside 8″x17″ boards. Now the piping should be going straight up into the air. This is your chance to make sure everything is secure and even.

Step 6: Add Top Wooden Shelf

I then placed my final top shelf (8″x36″) on top of the top set of flanges and used my level to make sure everything was even. I then used my drill to screw in the last two flanges – don’t fully tighten each screw until you have everything in place.

Step 7: Add Hooks & Decorate

The last step is to add 4 hooks into the bottom of the top shelf. I drilled pilot holes with my drill and then screwed in each hook with my screwdriver. YES! We’re done!! Now it’s time to decorate the hall tree and enjoy your master DIY skills!

Don’t forget to take Before & After pictures of the area and tag me @maykitdiy if you try this DIY.

Furniture Contest 2018

Participated in the
Furniture Contest 2018

Be the First to Share


    • Tinkercad Student Design Contest

      Tinkercad Student Design Contest
    • 3D Printed Student Design Challenge

      3D Printed Student Design Challenge
    • Pumpkins & Gourds Speed Challenge

      Pumpkins & Gourds Speed Challenge



    2 years ago on Step 7

    I really like this! Nice and Simple! Voted! Good luck!


    Reply 2 years ago

    Thanks for your support! I am glad you liked the DIY :)


    Question 3 years ago

    Are these crates sturdy enough that if they were all placed horizontally, with perhaps a board over the top, that it could be used as a sitting surface? For taking off boots, etc.? It looks great!


    Answer 2 years ago


    That was actually my intention when building this (to add a board with hinges to create and open and close bench) but somehow the wood piece got cut to the wrong size at Home Depot so that is a project for another day :)

    I think it would be sturdy enough to sit and put shoes on. Just make sure you have a thick enough wood board so it doesn’t dip or bend when you sit on it.



    3 years ago on Step 7

    I love it! Strong and practical. Well done :-)


    Reply 3 years ago

    Thank you! :)

    DIY Hacks and How Tos

    That looks great. I need to make something like this at my new house.


    Reply 3 years ago

    Thanks! It is both practical and aesthetic. Highly recommend you try it out :)