Introduction: X-Wing Voice Control Drone Star War
hi friends I uploaded this instructable for sci-fi contest.
*first of all please vote me ?
I this instructable we are going to x-wing drone to give tribute to the amazing star war.
this drone is very cost effective.
and the most amazing thing about it is that it is voice controled .
and not only it can fly it can do hip hop , became unstable, self-destructs itself, with one command it can land , it can create Tesla turbine motion in air
please vote
it is the result of one year of research and development.
humble request only one vote from you.
*first of all please vote me ?
I this instructable we are going to x-wing drone to give tribute to the amazing star war.
this drone is very cost effective.
and the most amazing thing about it is that it is voice controled .
and not only it can fly it can do hip hop , became unstable, self-destructs itself, with one command it can land , it can create Tesla turbine motion in air
please vote
it is the result of one year of research and development.
humble request only one vote from you.
Step 1: MATERIAL REQUIRED
*Arduino pro mini
*Bluetooth module
* 3.7v lipo 100Mah battery
* coreless motor
*propellers
*100 ohm resistor
*2N2222 NPN transistor
*P.C.B board
*Bluetooth module
* 3.7v lipo 100Mah battery
* coreless motor
*propellers
*100 ohm resistor
*2N2222 NPN transistor
*P.C.B board
Step 2: STEP 2: PROGRAMMING ARDUINO
first you have program Arduino pro mini
codes:
https://drive.google.com/file/d/0B5clE--gYwwORjRfUTJ3RmFCMG8/view?usp=drivesdk
codes:
https://drive.google.com/file/d/0B5clE--gYwwORjRfUTJ3RmFCMG8/view?usp=drivesdk
Step 3: STEP 3: CONNECTING ARDUINO TO BT MODULE
Arduino= bt module
RX =TX
TX=RX
VCC = VCC
GND = GND
RX =TX
TX=RX
VCC = VCC
GND = GND
Step 4: STEP 4: MAKING DRIVERS
for making driver see all images listed above
and install on top on Arduino as shown above.
and install on top on Arduino as shown above.
Step 5: MAKING FRAME
for making frame I used bamboo sticks
and for sticking motors I first wrap black tape around it and then apply device kwick glue on it
note that two motors should spin clockwise and two anti clockwise
and for sticking motors I first wrap black tape around it and then apply device kwick glue on it
note that two motors should spin clockwise and two anti clockwise
Step 6: STEP 6: COMBINING FRAME AND CONTROLLER
for installating controller on frame I stick two hard strow and connection are shown above
Step 7: STEP 7: MAKING X-WING
you can learn how to make x wing from origami from YouTube
Step 8: STEP 8: INSTALLATION OF X-WING ON DRONE
just install as shown above
Step 9: STEP 9: CONTROLLER
first you have to download app:
https://drive.google.com/file/d/0B5clE--gYwwOa3FBSzBRcy14S1U/view?usp=drivesdk
then you have to configure vocal codes
as given below
https://drive.google.com/file/d/0B5clE--gYwwOa3FBSzBRcy14S1U/view?usp=drivesdk
then you have to configure vocal codes
as given below
Step 10: VOCAL COMMANDS
you have to configure this code in app.
Step 11: TAKE a FLIGHT
now connect your batteries
then connect your Android device with X-wing
say commands .
then connect your Android device with X-wing
say commands .
Step 12: VOTE ME IN SCI-FI CONTEST
for much things watch my YouTube channel
SCIENCEINO
and if you want to contribute to my super project you can help by donating Amazon gift card
on 909garvit@gmail.com
SCIENCEINO
and if you want to contribute to my super project you can help by donating Amazon gift card
on 909garvit@gmail.com