charging

Hello sir,  Im intrested in solenoids feild and wanna have practical experince in that.can you please tell me how to generate electrical charge by using solenoids and storing that charge in mica capacitors with less voltage rating high storage capability..which also has slow discharge. The time of storing the charge should be high.Hope will guide me. Thankyou. Raghudeep,

Topic by RaghuC   |  last reply


Battery Charging? Answered

If i charge a battery when it's half full will ruin the battery life between charges?

Question by KnexFreak360   |  last reply


Charging Circuit

I was wondering if anyone had any ideas on how to make a circuit so that I could charge a battery, but that I can also power an amplifier when the battery is not charging. Currently I have a switch that switches between a charging circuit and powering the amplifier, but I was looking for a way to do this without having a switch that I have to control

Topic by Fozzibehr   |  last reply


battery charging?

How can i charge my battery, i've lost my charger. the battery is 14.4V 1.5Ah Li-ion

Question by johnnywgk 


Solar charging

Hi, pls suggest me for the following A 20Watt ( 20V , 1000 ma) solar panel is connected to charge a 12V, 80AH battery . What is the value and wattage of a Current limiting resistor to be added?

Topic by khhrao   |  last reply


Capacitor Charging?

How do I charge a capacitor rated for 450v at 1150uf using 2 AAA batteries? I tried using a mini transformer but it takes a very long time. Is there a quicker solution? Thanks in advance, IndianHacker

Question by IndianHacker002   |  last reply


charge battery

I have battery 1cell NI-MH AA 1.2 v 1500mAH   and i need to charge it by using smps and diode for detect peak voltage of battery   i prefer fast charge for maximum 2 hours for my project  how much voltage and current i need in output of smps ?

Question by omar kotrash    |  last reply


Battery Charging?

Hello, So I have a 9.6 volt  NI-CD 4 hour quick charger and the battery(600mah) that goes with it, but I was wondering if I could charge a 7.2 volt 2000mah, Ni-Mh battery with it. If i can for how long?

Topic by ben2000   |  last reply


Charging a capacitor? Answered

Recently I've had an idea for a project that requires a relatively low voltage (5 to 30 volts) capacitor bank. However, that capacitor bank needs to be charged. While I do know you can easily just hook it up to power, I find that too simple, and lacking of safety, and knowing when it is fully charged. So, could anyone please enlighten me on how i can charge my cap. bank relatively slowly, with, say, an LED that lights up when charged (to avoid them blowing up in my face), and a kill switch/button that discharges the capacitor bank in the event of an overcharge. If anyone could provide an explanation or circuit diagram that would be great, thanks. BTW, the capacitors I was planning on using are http://www.goldmine-elec-products.com/prodinfo.asp?number=G17623 or http://www.goldmine-elec-products.com/prodinfo.asp?number=G16573.

Question by LiquidLightning   |  last reply


batery charging

Having had to buy a dedicated charger for some 18650 cells (at my wife's insistence) I took an interest in these cells for the first time and their smaller cousins the 123a. At with maximum capacities I've come across so far of 3700mAh and 2000mAh respectivley that's twice the capacity of the battery in my smart phone and 2.5 times the capacity of the one in my basic bar phone. The smart phone width would accommodate 3 of the 18650 cells (6 days without charging at my rate of use) and the bar phone possibly 4 of the 123a's (70 hours talk time or 10 months on standby). Yes this would mean a custom made back, but there is at least one instructable on molding a GRP/ carbon phone back adjusting it to take extra cells and maybe ports just needs modeling clay. I suppose I could just carry a power bank, but why if the phone can be its own power bank? Removing the guts of a power bank and building a new phone back to accommodate them may be the simplest answer to this but, my questions are:- A) I've got old mobiles laying around could I use their charging circuits to charge these standard Li-ion cells? Assuming that is a yes that would mean a long charge every 6 days/ 10 months. I gather there are problems associated with parallel charging/ discharging of Li-ion cells and over discharging so, B) Any advice on doing this other than don't? On the assumption that's a don't or even if its not this strikes me as a safer possibility. C) Could a micro controller be configured to discharge one cell to its limit then switch to the next full cell. D) Could a micro controller be configured to charge one cell to capacity then look for the next under capacity cell and charge that. E) if so could it do both at the same time? If A is possible and the rest not then a multi position switch is  probably the answer.

Topic by Stan1y   |  last reply


Induction Charging ? Answered

OK, I have disassembled a old electric tooth brush and I am trying to reduce the size and one of the things I have deemed unnecessary is the PCB that runs the timer built into the toothbrush. However, one thing I am wary of at this moment is that the toothbrush is a induction Charger which is a A/C and I don't know if I can just remove the board and be OK or do I need to rectify the current into D/C to continue charging the battery. If the latter is the case what do I need to achieve this?

Question by Jayccob   |  last reply


Wireless charging? Answered

So i would like to make a simple wireless charger for an ipod (ok ok its not so simple once you factor in the ipod) but i want it to be able to show a charging sign.... also it would be nice if it waould work from one or two feet apart minimum. I heard guys at MIT made one for a 60 watt lamp that worked 2 meters away... so its possible... i can probably order any circuitry if it is reasonably priced and available at digikey or mouser. :) I have access to several ipods so it doesnt really matter what model i use. I also know that this would probably make a huge electromagnetic wave... possibly? idk... but if it is big enough to destroy nearby electronics i might not want to try... So i am all for distance- the farther the better.... Also base power is not an issue, i can use a wall wart if i need to...i can just see an ipod touch with 500 passes of wire around it 5 feet away from a 2 foot square power station..... all while erasing my hard drive :) Soo.... im coming back to reality for a min.... anybody know any sites....any formulas too!! Thx! :) :)

Question by astroboy907   |  last reply


How to charge a capacitor? Answered

I read some where that you need a rising amount of volts to charge a capacitor, but I also always see around that you can just charge a capacitor on just a straight battery that is DC. I am very confused how you can and should charge a capacitor.I think the formula for charging a capacitor is i=C(dV/dT)Thanks

Question by squirt8500   |  last reply


How to charge this capacitor? Answered

I got this from a lightbulb. (three way)

Question by Xixfas   |  last reply


Charge controller CM3024z

Hi,  im a student, i just  wanna ask if i can use the charge controller CM3024Z to a Magneto (alternator) and coupled with a solar panel 50watts? does the solar charge controller are for solar panel only? thanks godbless

Topic by romeob   |  last reply


LiPoly charging question?

Hi Everyone, I am creating a 6 cell pack (first time as you can tell) of LiPoly batteries 14.8V 5A it will have 3 groups in series of 2 in parallel for a 44.4V 10A pack. In order to properly charge and maintain the batteries does anyone have any recommendations for a good balance charger from hobbyking or elsewhere? Also in order to properly charge them should I charge each of the 6 cells individually, or charge the 3 packs of 2 in parallel using these?  Thanks for your help.

Question by Hammock Boy   |  last reply


SLA Battery Charging? Answered

Quick question about charging SLA Batteries, I haven't really dealt with battery charging too much in the past.  I have two 12v 5Ah SLA batteries, in series, and I have built an under/over voltage protection circuit for each of them, but while charging I noticed that testing voltages across each battery, they are different, however, as soon as I remove the charger and test them as is, they have the exact same voltage (+/-0.05 volts, they are very close).  Is this just because the charger is hooked up, or should I be worried at all about that? I am charging them to 14.75 volts each, or would like to, they say they should be charged to 14.5 to 15v right on the front of them.  While charging they both climb, but one climbs faster and stops once the voltmeter reads 15.2v across it.  0.2v over the rated value really doesn't seem to be of major concern, I just find it odd the different voltmeter readings across the batteries are different while the charger is connected and identical when its not.  Does it have something to do with charging them in series?  I did read that you really can't measure batteries while charging, you have to disconnect the charger first, but any insight would be appreciated.

Question by Electric Spectre1   |  last reply


Over-Charging Capacitor

What happens if you connect some form of dc power source that supplies 100 volts to a capacitor that is rated for 100 volts, and leave it plugged in for a long period of time. would it eventually "over charge" and explode? would it over heat? would it loose its  ability to store energy?

Topic by merlinj   |  last reply


12v battery charging?

I'm making a prop that has 6 12v 6800mAh rechargeable batteries, but i wanted two ways of charging them, a normal plug in to a wall adapter, but also jump lead connectors, so I'm able to charge it of a reving car, or a leisure battery, all my questions are, is what would i need in the circuit to make it safe, and work, imbetween the jump lead charge wires, the normal adapter charger lead, and the batteries them selfs. JUMP LEAD------------  ??  ----------------------------       WIRES                                                          |                                                                             |------------------  ?? -------- BATTERIES ----------12v -------                                                                             |                                                                             POWER ADAPTER------------------  ??  ------------|                       

Question by infinity1   |  last reply


Waterproof charging input?

Hello everyone, I'm new to electronics and while I can usually find what I need by asking good ole' Google, I decided to try asking a forum of people more knowledgeable on the subject. My question relates to the charger input on devices with internal batteries. I have a Braun razor that can be used in the shower, and I was curious how it can go in water with the two charging prongs exposed? Thanks in advance! 

Topic by alpizzles   |  last reply


charging batteries with 240V? Answered

I was thinking, wall transformers only transform so much energy(70-90%?) the rest goes off into heat. so, wouldnt it be better to charge 160 AA batteries at the same time in serial (thus making 240V) directly off the wart? i know this is just theory, since its not practical, not managable or anything, but i just wondered if it could be done. would this solve the energy loss from heating the transformator up?

Question by godofal   |  last reply


Charging Multiple NiMH

I'm modding something (secret, Instructable later) and there's going to be some integrated NiMH batteries to replace the one 1.5 AA battery that the device use to use. Due to funky space constrictions, I'll be using 7 tiny 320mAh 1.2V NiMH coin cells in parallel (to get a decent amount of maH). How hard is it to charge a bunch of batteries like this? Could I get a chip from a place like Maxim or TI? All of their chips require the batteries to be in series... Thankyou!

Topic by guyfrom7up   |  last reply


USB charge. Will this work?

Will this work? please reply with this LED work for me.....If i put the  USB cable from my phone or mp3 player  instead of the diode...Will this work? P.S.  my english is not very well

Topic by Gvozdenovic   |  last reply


Wirelessly charged mouse

I need some help from all yall out there. My idea is a wirelessly charged mouse. The mouse pad acts as the transmitter coil, and the receiver is in the mouse. The concept might not be phenomenal for gamers, but would be a step into getting rid of wires on our peripherals and really making wireless charging reality. Perhaps a .2 farad super capacitor (.2 Farads ~ 400mAh) could be used to prevent the mouse from dying if you drag if off the pad for a few minutes. I'd need help conceptualizing it and for those of you who know about electronics, assisting me in designing a schematic. The design would be open source so we can have literally anybody contribute and improve the idea. Leave a reply if you want in!

Topic by JesusG33k   |  last reply


how can i call my friend with out the use of money or a phone? Answered

My friend is long distance and if i want to call him i cant because my phone charges for long distance and i dont want to pay for skype any ideas around this?

Question by knexsuperbuilderfreak   |  last reply


Are capacitor charging circuits necessary? Answered

So I was looking at some coilguns and all of them have a circuit to control the charging, is this really necessary or can you just apply the voltage you want and let them charge.

Question by jj.inc   |  last reply


charge a capacitor with a bug zapper ? Answered

Can i charge a capacitor rater for 450v 680uf with a racquet shaped bug zapper's circuit.

Question by mind power   |  last reply


What is the strength of the other charge?

I need help with solving this problem in physics class. I know Coulombs equation F= k(q1q2)/r^2 The force between two charges is 2 newtons. The distance between the charges is 2 x 10 ^ -4 meters. If one of the charges is 3 x 10 ^ -6 C, What is the strength of the other charge?

Question by Baseball24_7   |  last reply


MP3 Battery won't charge?

I have just bought a generic MP 3/4 and did not fully charge the battery before exploring it's apps. Now I have a half full battery that won't charge any further. Can anyone help?

Question by willywombat   |  last reply


Charge battery with bike dynamo

Hello, I would like to charge a battery using my dynamo on my bike. The battery I would like to use for my head and tail light for example and for charging my phone. Would this be possible and how? Thanks in advance

Topic by doppiej   |  last reply


charging a 450v 1800uf capacitor?

Hi how would a charge a 450v 1800uf capacitor? i used to charge it with a photo flash circuit but the small capacitor would burn out making me unable to charge it. i do not know how to read schematics. is there any step by step video any one can provide?

Question by justin.espinoza.790   |  last reply


Charging station for eee PC

Hi, I need a charging station for an eee PC 4G from ASUS. I was searching several days in the internet but I didn't found something. The cradle is only needed for charging nothing else. After working with the eee pc I only would plug it in the cradle upright for charging. Where I can find such a charging station for the eee pc or a station for an other device wich suits to the eee? If there's no matching station how I could build it by my self? Here's a drawing of my idea:

Topic by maddinel   |  last reply


Solar Panel Charging Station

Hello everyone, I am doing a project for my class and it is a solar lamp project. I was wondering if anybody knew how to make a simple solar charging station. I want to use  3 of 1.5 W/4.5 V solar panel from radio shack as a charging station. I was just wondering how I would connect this together and charge the rechargeable batteries from the solar panel charging station.

Topic by RedXNaruto   |  last reply


Charging capacitors with different currents? Answered

How does charging a big capacitor with a high current affect it rather than a low current? Certainly time taken decreased. What are other effects, and is it as safe as using a low current?

Question by ARJOON   |  last reply


charging 10s5p battery pack

I'm working on an ebike conversion. I'm buying laptop batteries to take out the 18650s and put them in my pack. I'm looking at a 10s 37v pcm. If I make it in 10 sets of 6 to get 37v 14.4ah, then how can I safely charge the battery so that they don't charge unevenly in each set?

Topic by leaf26   |  last reply


6v solar panel for charging

Is a 6v solar panel (260 mah) enough to charge 4 AA NIHM battery? The four batteries in serie amount to 4,8 volts, and  fully charged they can amount to 5,5v. I'm planning to add a diode, that can drop the voltage by 0,2v.

Topic by jemor143   |  last reply


Head unit not charging iPad

Hey All, In my car i have an after market HU with a usb port that my iPad 3/ iPhone 4s / iPods can connect to. However when my iPad is connected to it is unable to charge. The charging indicator in the iPad has the little lightning bolt going through it, indicating that it is indeed charging however the iPad looses about 7% of its battery every hour. Does anyone have any suggestions on how i can get my iPad to charge through my HU? Cheers  

Topic by wrignj08   |  last reply


How to positively charge something? Answered

I was sitting here in the middle of a thunder storm and I had a thought, usually the clouds are negatively charged during a lightning strike, so, if you used a large cannon to blast a positive iron ball into the air, you may be able to get lightning to strike it, then collect it to see what the lightning did. So, you would you charge a cannon ball? 

Question by jj.inc   |  last reply


How to charge up a capacitor? Answered

I heard some website just use a transistor and transformer circuit to charge up a photo flasher cap.(May be high frequency output) If so , can I charge up three or four capacitors with parallel or series circuit?

Question by james34602   |  last reply


how not to over charge a battery?

I want to connect my waterwheel to a car battery, but I dont want it to get overcharged and blow up! what can I do?

Question by tim13211   |  last reply


Strange battery charging idea.

So I have an Idea for a charger for a portable computer.  It will be solar powered, and charge li-ion batteries.  My question is how could I simultaneously charge batteries and power the computer at the same time.  No schematics are needed, just a quick written answer. Thanks!

Topic by Skiboy941   |  last reply


charge a battery while using it?

Https://www.instructables.com/id/Ammo-box-speakers-2/ hi, i'm looking for a way to charge a 12v deep cycle lead acid battery while powering an amplifier from the battery. Can i literally just attach the battery charger to the battery as well as the amplifier as long as the connections to the amplifier and charger do not touch? or is it not that simple?  The instructable linked above is what i what to implement it into. Any help will be appreciated! 

Question by WillERoberts   |  last reply


Charging SLAs from DC

Hi Instructables community! I am building a K9 robot - one that is going to be covered in solar cells-in such a way that I get a voltage / current ratio of a pretty high number. I plan to charge my SLA partially via these cells so I can lengthen the space between charges. Unfortunately, my 6V 4.5Ah SLA battery is charged via a plugin adapter and I do not wish to pull it apart unless there is no other choice - so is there are a way I can charge my battery from a constant DC voltage? If so, do any of you know what voltage/currents I'd need to feed it? I can get most any current/voltage specs via transistors and voltage boosters - just I don't know the equation. Thanks for all your help! Jonathan Davis NitroJon Labs

Topic by nitrojon   |  last reply


Charging multiple 12v batteries

I have eight 12v 18Ah SLA batteries that I need to wire to get 48v. I need to be able to charge them all at once, but can't find a 48v charger anywhere. Is there a way I can wire a 12v charger to parallel charge the batteries while they're wired in series?

Question by Charlie_Szasz   |  last reply


Using and charging at the same time?

Here is what i am trying to archive: 3 LED's to run off a small rechargeable battery or USB. It should also run off USB while recharging the battery.  Lake a wireless headset.  Thanks.

Topic by Squashie   |  last reply


Coil Gun Charging circuits?

Ok so i made this coil gun using a camera flash circuit but im using 450V caps so the circuit only charges to about 330V how would i step up the voltage in a cheap way. Buy another camera circuit or build one? If you need any more info just ask and thank you.

Question by rocket_man 


Best way to charge a SuperCap? Answered

Hi! I would greatly appreciate it if anyone would tell me the best way to charge a 2.7V 50F Nesscap supercapacitor. Any advice or ideas would help a lot; thanks! http://www.maplin.co.uk/p/50f-27v-super-capacitor-n51qq

Question by Digital Flame   |  last reply


Battery Charging Light Circuit

Dear All I am building a small scale PV system and I want to implement a circuit that will allow a LED to light up when the battery is being charged from the PV cells Currently I have a general purpose PNP transistor with a 2KOhm resistor for the base and a 1KOhm resistor in series with the LED, however when running this simulation the LED will not light, even when I lower the values of the resistors Any help would be much appreciated 

Topic by EmptyCoffin92   |  last reply


Balance charging li-ion ?

So I bought a replacement battery for a project. I tore down all the casing and got 6 18650. But I want to charge those batteries using the same protection circuit that was inside the casing using laptop battery adapter. Can someone tell me what are the terminal should i connect and how i connect? So far i found using multimeter that P-, P- is negative and P+, P+ is positive and there is no switch. The voltage can be checked directly. The circuit and battery is from Dell 1525.

Question by SaurIMX   |  last reply


why is instructables.com charging for membership?

We think of it, build it, create it, write the instructions, we take the photos and videos, then post it on instructables.com and they get paid for your work. Whats wrong with this picture? GO TO YOUTUBE and get paid for posting your creations.

Question by jimmynet   |  last reply