Vision Controlled Interface Controller

Is it possible to make a 360 controller and create a vision controlled (right) c-stick that I can use to aim at something simply by looking at it on the screen? Is this similar to what paralytics use to communicate? Is there any way that I could use that technolgy to OWN my cousin at Halo?

Topic by MattGyver92   |  last reply


Computer controlled remote control

Anyone here have ideas on creating a computer-automated cable box remote control, so that I could use my computer to schedule when to turn the cable box on/off as well as have the computer make the remote select the appropriate channel?

Topic by etelos   |  last reply


Controlling a servo with a Micro-controller?

So I decided to spend some time to make a "gimbal" in a very loose sense. Basically I was experimenting using a square wave oscillator to generate the correct PWM to have a servo rotate between 0 and 180 degrees when a tilt sensor is tripped. After some research multiple sites said having a 1ms pulse every 20ms would have it move to the 0 degree position. Great so I will make a oscillator pulses ~1ms on one side and 19ms on the other. However this does not seem to be working. I am curious if it is a fault in my math or if the tolerance on the parts I am using are just too wide to be any good. Here is a diagram of my set-up with the values a came up with. One spot that may be weak is that I just notice someone somewhere mentioned using 50Hz for the timing I just used that number when I calc my figures. Any feedback?  Also a side note is that I have been able to move the servo in one direction only and by accident ( in fact it's what inspired this project) when C1 & C2 were 2.2nF and the R1 & R2 were 10k potentiometers that I turned until something happened. Now that I am trying on purpose no results. 

Question by Jayccob   |  last reply


Controller Camera

I'm new to this sorry. I want to make a wireless contolled camera or some thing that use either the ps1 or n64 controllers. Like if you press X it will take the photo. I want to have a display near or on the controller so it can be viewed with out the camera. As well as a usb cable so it can plug directly into the pc. I know it sounds like a lot too but I have most of the parts.

Topic by squall_01   |  last reply


charge controller

I have the cm3024z charge controller. i have 240 watts going in, controller going to batteries, no conection on the load,   have 1500 watt converter hooked to batteries. set the controller as such,,, HvD-14v, LvR-12.5 v'  LvD-10.8 v . my voltage comming in to the controller is good, when i get to the hvd it kicks out at 14v as it should, but my lvr doesnt want to kick back in. i have let the batteties drain below the lvr but will not kick back in ..  is there anybody that can help with this, i have retured the first one and this is my second one with same problem. i have left the system hooked up as acording to manual,but after it kicks out it just wont kick bavk in unless i disconnect the panels and reconnect them.   all help would be appreciate, thanks

Topic by puddlepod   |  last reply


Motor Controller

Dear Sir, Can you help me in developing a 24/36 mosfet controller for tricycle? Regards P​

Topic by hgsan   |  last reply


speed controller ?

You can make a washing machine motor with the module and taco run with a potentiometer switch to give you speed control over the motor I have the planes for a hot point motor but not the motor im using !! does anyone have the no how as to with leads to connect to contact mrkeithg.rumsey@tesco.net

Question by rumsey   |  last reply


Second controller?

Hello, peoples! I want to install a second xbox 360 controller onto my PC, so that my brother and I can play games together without me having to use the keyboard and mouse and having much rage quit happen. But, the lovely people at Microsoft say that it isn't possible to install more than one controller on a PC, but I know that's bull because I've seen people do it before.  I already have one installed; I have the driver and everything. But my computer doesn't even look at the second controller like it exists.  What is wrong, how do I fix it and how can I make gaming easier? Thank you for your time!!

Question by RoadkillJoe667   |  last reply


capacitor control

I was just wondering if anyone knows any methods of controlling the energy discharge from a capacitor..

Topic by nuncoop   |  last reply


Motor controlers?

I have a 24 volt motor from an old mobility scooter and I want to control it with my arduino but I have no idea what motor controller to use. I presume that I will need to use PWM to control it but what hardware to use I have no idea. Any help I would really appreciate. Thanks

Question by cheesemarathon   |  last reply


Remote Control

Hello people! I was wondering if anyone knows how to hook up a computer to a remote control from a bluray, so I can do stuff with the commands from the remote.

Topic by Game Maker   |  last reply


House Controlling

I have pic18F2553 with interface  and it is programmed on c++ for 1/0 how to make it controlling house lights and windows?? im physician but i know alot of things about houses building

Question by Tariq R.Hijaz   |  last reply


Temperature control

Hey I am wondering how to make something to shut off a heat source at a certain temperature. The heat source is a normal appliance that is plugged into the wall.

Topic by lun0s   |  last reply


Radio control. Answered

I have radio control radio and receivers from different cars with different AM. They are all 49 mhz, can I change AM by replacing old resisters at  the right spot and put less resistive ones to make it work? Any way?

Question by jbaker22   |  last reply


Cnc controller Answered

Im building a cnc machine and want to know whats the best free milling software i dont have a parralel port only usb

Question by hightekrednek2396   |  last reply


Controlling Amperage

Hiyas, I was wondering if you could point me in the right direction. I was wanting to build or buy something I could control Amp input. The system would be 12 -14 v dc and I want to be able to limit the input to say... 25 - 30 amps. So if a system would naturally draw more amps I want to be able to control the system be limiting the amp input...if that is making any sense. Got any thoughts ??? tks Huchleberry

Topic by huchleberry 


Ambilight controller

Hey guys,has any body tried the ambilight controller like the one here ==> http://www.hacknmod.com/displayMOD.php?hack=990the link for the controller points to some weirdly languaged (hope thats a word "languaged") site but with no content. i am preparing my comp for fragapalooza (canada's largest lan party) so if any one has done/looked up this mod, please point to a schematic for the led controller...the controller is connected to a pc with a serial cable and has many outputs to connect chains of leds plus i think there is another power supply to power the leds (as the chains of leds are long)...any help is appreciated...note: this is a multipost to produce results efficiently...i hope...***update: nothing after 3 days at bit-tech or fragapalooza.com...:(

Topic by Slisgrinder   |  last reply


REMOTE CONTROL

I'd attached two pictures here. can anyone help me with this? at least let me know what it is called so i can further search how to utilize it with my device. is it possible to use this with arduino & how i connect them? if possible i want to use it as my remote control for my device. it is wireless. however i don't want to use it as wireless. help me please because using push button does not work. thanks.

Topic by lovetronic   |  last reply


REMOTE CONTROL

Someone can advice me what switch is suitable to use in my remote control. I had tried push button however it does not compatible with the coding (I'm using chipkit UNO32). My intention is to make the user select AUTO mode or MANUAL Mode. After selecting, the user will be asked to select speed and duration. So this requires a lot of loop-inside-a-loop, if-inside-if etc. When I'm using push button, the microcontroller cannot read the command when the second button is push. I heard, if using push button I need electronic relay. 

Topic by lovetronic   |  last reply


temp controller

Hi dont know is anybody can help replacing the batteris in my drill pack and found that it has what looks like a thermistior??? to control chaging temp.  unfortunatly when dismantling I shorted it out to + and i believe blew it. i need to renew it as it lookslike it feeds relay in charger to switch  when fully charged (its a 1 hour fast charge)  how ever dont know what it is . it appear tobe connected in series with a resistor ???(again not sure can up load a photo if it helps) the thermistor is 2 wire and marked M20 tp118/c 02c if that helps, the resistor 05u-045G peter

Question by peter354   |  last reply


accelerometer controller

Hi I’m making an accelerometer (3-axis) that I want to be able to work in some programs and games. I haven’t built any tech´s before. Hehe so plz replay with easy words. There are some tutorials out there which are based on an old game controller and stuff. But I want to do my on an Arduino board with a USB connection or wireless connection. Here is a tricky part, I want it to fit a cube chassi that is around 7-10 centimeters, I haven’t done it yet so that’s why I put it to 7-10 cm because I have still time to make it bigger or smaller. I don’t know much about the wireless connection and battery to make these things. I know I’m sounding like someone that doesn’t have a clue about these things and it’s true, I want to learn it and make this controller. If someone can tell me more about this sort of project or tips me to a tutorial or something it would be excellent.

Topic by Blackanemone   |  last reply


How to turn a Ps2 controller into a Pc controller ?

Hi i was woundering if there is a way to detach the end of a ps2 wire and conect on a usb plug would this be posiable. Any other idea would be much appreciated.Thank you

Question by walterh9   |  last reply


Building a cnc controller?

I am building a homemade cnc machine that will have an X Y1 Y2 Z and eventually a lathe. And I was wondering if I could use an 4-axis Breakout board, and just run the Y-axis to two different Divers to power the Y-axis stepper motors. If not what would be a good breakout board that is able to connect e-stop, Homing switches, router on off, and touch plate. 

Question by Rileigh Crow   |  last reply


Radio controlling the SSC-32 Servo Controller?

I am planning on making a RC humanoid robot (like the ones in the kung fu competition at robogames), and I am probably going to use the SCC - 32 Servo Controller.  I am pretty sure that you can use a ps2 remote to control it, but on the robogames website it says that they want you to use a PCM controller.  How would I connect a PCM controller to the board?  Also is it even possible?  If it is not then would the controller that the robonova uses work with a PCM controller? Thanks in Advance!

Question by JaredsProjects 


Controlling an old printer for motion control or robotics?

Are there some interface basics that would allow someone to use the drives from an old printer as budget CNC or robotic actuators? They are certainly accurate, and there are plenty of them available.

Question by wgyure   |  last reply


Can you control arduino with a gamecube controller? Answered

I want to control arduino with a gamecube controller to drive robots and for other projects. I was just wondering if its possible and if anyone has a code they would be willing to share. I would love to do it on my own but I  new to programming and am not sure what i am doing.

Question by Jgniklu   |  last reply




processor ? Answered

Hello I need someone to check my work I want to know reason that I have explained in my post is right or wrong ? Q1. If data is 4 bit ,which alu you should have to use A . 2 bit ALU B . 4 bit ALU C 6 bit ALU D 8 bit ALU my answer . (B) 4 bit alu reason : data is 4 so I used 4 bit alu . 4 bit alu deal with 4 bit number like 0001+1010 Q2. If data is 8 bit,which data memory you should have to use ? A. data memory 8 x 256 B. data memory 4x16 my answer .A data memory 8 x 256 reason : If data is 8 bit , ALU is 8 bit so data memory should be 8 x 256 Q3.If instruction is 4 bit ,which program memory you should have to use ? A. program memory should be 4x16 bit B. program memory should be 8x256 bit C program memory should be 6x64 bit my answer A . program memory should be 4x16 bit reason : Instruction are 4 bits so program memory should be 4x16 bit Q 4. If we have 4 to 16 Instruction decoder , how many instruction it can decode ? A. 8 instruction B. 16 instruction C. 256 instruction my answer (B) 16 instruction reason : 4 control word can decode 16 instruction Q5. Why Program counter is 4 bit ? A. 4 bit program counter can address 16 instructions B 8 bit program counter can address 256 instructions C.16bit 4 bit program counter can address around 6500 instructions my answer. A because 4 bit program counter can address 16 instructions please checkout my work ?

Question by vead   |  last reply


8 bit Instruction set ?

Hello experts I need some help I want to make 8 bit instruction using folloing component so I made one simple example 8 bit instruction set 4 bit opcode + 2 bit source register +2 bit destination register+ 4 bit data accumulator A memory register R1 memory register R2 memory register R3 opcode         source       destination       data 0010               00               00                 xx                  R1  01           A  01                xx                  R2  10               XX                xx                  R3  00               XX                xx load data directly into R1 mov R1#data opcode     source      destination       data 0010         R1 01          00                  data load data directly into R2 mov R2#data opcode     source      destination       data 0010         R2 10          00                  data load data directly into R3 mov R3#data opcode     source      destination       data 0010         R3 11          00                  data load data directly into A mov A#data opcode     source      destination       data 0010            00         A  01                  data mov the content of R1 into Accumulator mov A, R1 opcode     source      destination       data 0010         R1 01          01                  disable mov the content of R2 into Accumulator mov A, R2 opcode     source      destination       data 0010         R2 10          01                  disable mov the content of R3 into Accumulator mov A, R3 opcode     source      destination       data 0010         R3 11          01                 disable don't use any register disable opcode       source       destination       data 0010               00               00                 xx      don't use register

Question by vead   |  last reply


Charge controller CM3024z

Hi,  im a student, i just  wanna ask if i can use the charge controller CM3024Z to a Magneto (alternator) and coupled with a solar panel 50watts? does the solar charge controller are for solar panel only? thanks godbless

Topic by romeob   |  last reply


8051micro controller programming

Hi friends.................... i am working with 8051micro controller programming,I have created HEX file using  keil C compiler and proload to burn the HEX file in to the micro controller .iam using serial communication BUT ...........MY computer is not detecting the programmer nor micro controller.........why?...............is there something wrong  with my PC ?

Question by sunil sheth   |  last reply


Treadmill Motor Control

I have a Horizon T101-04 treadmill that has a control problem. The motor is definitely good. I suspect that the motor control board is good, and the control panel board is bad. The control will not reset or go into diagnostic mode. I want to replace either the control panel board or the entire control system. The motor is 90V DC. For amperage, the motor label says "19A S6 25%" which has no meaning that I understand, other than perhaps that the maximum amperage is 19. The label says "APMS" rather than "AMPS", and I wonder if the "S6" is supposed to be "SC" for "stall current." All of the characters on the label are very legible. To replace the entire set of controls, I can use an industrial DC motor control, but how much horsepower does the control actually need to be able to provide? I don't think that the one on the treadmill actually provides 19A, and is probably close to 1 HP or so in its capability.  To replace the control panel with something else and keep the existing motor control, what do I need? Do I need some type of complex driver circuit? Does it need feed back from tach sensor to do a good job of keeping the speed steady?  If it will work well, I want a simple control set up like a KB Electronics KBMD-240D to which I will add a safety cut-off switch with a lanyard.

Topic by Ineedacircuit   |  last reply


controll a stepper motor

Can you controll a stepper motor with push switches no circuit? i need a 12v motor with pllanty of speed  torque for a diy cnc but i want to controll it manualy with a joystick made with push switched can i just apply power to a stepper motor like a hobby 12v dc motor and run it without a circuit?

Question by skullkeeper80   |  last reply


Mobility Scooter Control?

I am looking to power a kart with a mobility scooter motor and transaxel. The motor controls start at about £135, but you can get just the pot for about £30. I'm only going forward, so do I need the entire controller, or will just the pot do the job?

Question by pip.cartwright.3   |  last reply


N64 USB controller?

Trying to find a good and cheap schematic to convert a n64 controller into a usb i do have some experience with schematics but i must admit its been a couple years thanks

Question by nimbian   |  last reply


N64 Controller to PC

Hey guys, I recently pulled out my N64 and played Mario Kart 64 for some old-time fun. It was a rush.Anyways, I saw a video on youtube of someone who hooked up their N64 controller to their PC, and all the buttons worked.Now I recently saw an instructable on something similar to this:https://www.instructables.com/id/SNES-to-Parallel-Port/But I'm not sure if that same method would work or not.I also found this: http://arcadecontrols.com/Mirrors/emulatronia/n64pad/index.htmWhich is pretty much what I'm looking for, but I want to see if there's another way that doesn't involve the creation of a circuit with IC Chips.Anyone know? THanks.

Topic by Jackhole   |  last reply


Treadmill Motor Controller

HI, I would like to make a very simple controller my treadmill's Motor. Its MoBo went bad and I dont wanna fork over $200 for a new one. The motor works fine. I just want to make a very basic DC Motor speed controller. I know just a simple Pot or other variable resistor wont do.Will it? I've been messing around with Electronics since I was 9 so I'm not afraid to solder up some circuits even if its a complicated one. Im looking to spend around $50. Thanks.

Topic by AlxMad   |  last reply


remote control a webcam?

Trying to make my old Logitech wireless controller control my webcam. Like focus, up down, left right. Is this possible?

Question by neon2392   |  last reply


How to Control a Servo?

How do you control a servo? I know you can control it via Arduino or some other microcontroler, but can you control a servo with out the need of programing??? I know the servo has 3 wires red, black and yellow... and if what I heard is right, that yellow wire is for controlling it.... Thank you! Comodore

Question by comodore   |  last reply


alternator control mechanism

Im planning for a project on alternator control mechanisms. can anyone provide me relevant ideas about the topic?

Question by Puranjay Menon   |  last reply


Altoids or NES controllers?

As you probably know NES controllers and Altoid tins are popular cases for many mods. Which do you prefer?

Topic by NetReaper   |  last reply


Treadmill control console

I need information about treadmills control consoles, how they interact with the lower dc controller and why they are not interchangeable with others from another treadmill as they perform the same job?. Thanks.

Topic by abuyaseen   |  last reply


Control of 25 electromagnets

Hello Everyone, I'm looking for a controller to manage 25 electromagnets. I've managed to come up with a driver circuit to energise each individual electromagnet using an N channel eMOSFET in parrallel with a diode. I need a programmable controller to operate the gate of each eMOSFET but the controller must be capable of managing all 25 switches. thanks for any suggestions in advance.

Question by wameri   |  last reply


control via internet?

I'm new on this people i built a circuit & i control it with my PC if i wanna control it via internet should i buy static IP or I can upload my app on my website directly ?? if there another way that will be helpful 

Question by thijaz   |  last reply


Pwm motor control

Please send the circuit of cintroller

Question by avoymaity63   |  last reply


solenoid valve control

Hi, im wanting to build somthing simple to control the heater control valve on my fiesta. its a simple solenoid valve at 0v its open(hot) at 12v(14.4v) its closed(cold) the propper control board uses pulses to control the valve, the board has since given up and im left with a very hot car, now i thought a simple way to sort the problem might be to use the 10k pot on the control board with a MOSFET and just vary the voltage going to the valve. will this have the same effect on the valve?

Topic by stevelee10   |  last reply


Servo Controlled door

Hey I'm making an arduino controlled door. Will a servo provide enough torque to open and close a bedroom door?

Topic by fruitkid101   |  last reply


Manually controlling keyboard?

I am looking to control a keyboard using output from another computer. The output must control the other computer by the keyboard. or send keyboard strokes through the wireless keyboard adapter. I can not control second computer by a program, ethernet, or usb direct cable. I might be able to use usb if the imput show as if its a keyboard. I can use old style keyboard ps/2 or usb. I,m trying to control a computer that is on a VPN and it wont allow and connection or programs running like I mentioned. I could get by only controlling the mouse of the other computer from the frist.  

Question by dbartoletbet   |  last reply


Control robot with wifi?

Hello guys do you have any ideas how can i Control robot with wifi using arduino and a wifi shield

Question by omarb22   |  last reply