### Automatic LED light for cordless drill?

As far as I know, DeWalt has not incorporated lights into their cordless drills as some other manufacturers have.  Could someone make an LED light which would come on when the magnetic field produced by the drill motor is sensed?  Perhaps a sensor taped to the drill body, and a small LED light pointing forward, or a ring of light around the drill chuck?

Topic by jonwells   |  last reply

### Need help making this bunk bed a reality!

So, I want to do this project with my kids. They’re 5 and 7, and I want to start early in educating them that all this stuff that surrounds them is made by someone, and that someone can be them...Also, they want a bunk bed. :)Take a look at the photo...Can anyone help me turn this picture into a design? I’m pretty handy, but I’d love it if someone with the carpentry-and-CAD skill intersection could take a crack at turning this pic into something I can use...Best,Dutch

Topic by DutchFlyer   |  last reply

### Large motors and electronics classes

Hello,Is it just me, or there's something wrong with "Large motors" and "Electronics class" by randofo? It looks like there's nothing in comparison to just yesterdady, whereas I bought a premium account just to download his classes. Another problem is that I can not enroll or download any classes.Can You help me?

Topic by Emerid   |  last reply

### Torque to linear thrust through lead screw

Hi,I am trying to figure out maximum linear force I can produce with an electric motor through use of lead screw and nut. I have come up with an equation which seems correct but resulting forces are way higher than my intuition believes is correct.I tackled the problem from the perspective of energies:F' * p = M/r * 2*π*rlinear force * thread pitch = torque / radius [M/r = force at radius] * circumference of lead screwF = 2*π*M/p * (1-k) //k stands for coefficient of friction between lead screw and nut)Radius falls out of equation, which seems fine as force is provided by torque, which is radius agnostic. I used a 7€ stepper for source of torque which can provide 0.42 Nm of torque and a lead screw with 8 mm pitch and 4 mm radius, I assumed 15% losses. My equation tells me that such system can provide 280 N of force, which seems wayyy too much for a cheap motor.I have attached a python code that calculates linear force in case it helpsCan someone tell me if my equation is either correct or flawed?

Topic by ptkrf   |  last reply

### Electronic repair after a voltage spike or power surge

So far I was lucky and never got a lightning strike or other power failure to induce high voltages into my house and equippment. But over the time I got several requests from friends to take a look at things after literally all connected electronics in their house got fried. In some cases there is only a total write off as due to a lack of surge protectors inside all unwanted juice made it's way into vital components. Like a brand new Samsung TV where the replacement of the power board was the only option - which makes you wonder... But in other cases, like microwaves, induction cooktops, computers and such I had some good success with the repairs. Guess it comes down to purs luck on both sides, power surge was not too bad and simple components on the input side failed quickly enough to prevent damage to microprocessors or other sensitive parts. Right now I have an induction cooktop here again that failed after a mains transformer in street blew up during a thunderstorm. I can tell it was bad as everything in the area of fried parts has a vaporizsed metal film on the surface and not much is left that was a surge protection. I cleaned all up, replaced the varistors and missing parts of the traces on the circuit board but the cooktop is not performing the way it should anymore :( At some stage during cooking it turns off with a meaningless error code stating the input voltage was out of bounds. So my next attempt was to literally remove every single component from the filter and power supply board to measure for any possible connections between the traces. By doing so I noticed several points where I had a quite high but measurable resistance in areas where there should be none. Mostly on the direct input side where the varistors tried to save things. So I used my Dremel in a tin drill press to cut the circuit board aourd the affect areas (where possible with a drill, otherwise with a thin grinding disk).. Sure enough I was greeted by charcoal colored dust in several areas. After removing all material until the dust was "clean"  tried again and this time all seems to work fine. I would like to use this topic to offer some help and guidance in case you have devices that suffered a severe power surge of some sort. Many of us either have no insurance to replace those items or even if you do the device might be expensive enough to try a repair despite getting it replaced. Trust me, even it went up in smoke there is still a chance to fix it in some cases and if proper protective circuits were in place the repair could as cheap as a few Dollars for replacement parts. To get useful advice the following things should be included in your request: Some clear pictures showing a close up of the affected parts - if there is visibale damage to be seen. A brief description of what happened, e.g.: lightning strike directly into the house or outside power lines, generator or inverter failure or simply that the power company stuffed up and your entire street was affected. Of course you will need the means to take the device apart for investigation and also some basic soldering skills or somehow how has and can assist you. But if you are up to the challange I am willing to help if possible.

Topic by Downunder35m   |  last reply

### How much is granite worth?

So today I went down to some local woods with a hammer (Geode,granite,marble hunting) and I saw that 2 friends of mine had dug up a 20-30 pound rock. It was a heavy little bugger. So I swung the hammer at the rock for half an hour until I had about 30-50 small chunks of granite. The main reason I broke it was so that me and my friends could split it. One of my friends didn't want it. The other friend wasn't allowed to have it. All that was left was me. So I then realized that it was way too much to carry around. So I told another friends that didn't help do anything but polish the freaking thing with a brush *pauses and laughs* that I would give him all of it but 3 peices. I'm starting to regret saying that. So I wanna know... is granite worth anything/expensive?

Topic by Flumpkins   |  last reply

### phone charger

My wall phone charger is busting up could i just make a usb charger out of it, and howdo i go about doing that, the phone is a samsung

Topic by Rotten   |  last reply

### Why is it so bad that the small bakeries disappear more and more...

Topic by Downunder35m

### Removing Broken M2 Tap from Anodised Aluminium 2014.

Hello Everyone,As you might have read, I have a Milled Aluminium 2014 Block which is Anodized with Black color, Today when I was tapping the holes of it, the M2 Tap broke and got stuck inside that hole, there is no portion of it outside the hole, so I can't unscrew it and pull it out.I saw a few videos on youtube on how to use alum water, or electrolysis(with 10% dil H2SO4) to dissolve or chemically remove the Tap bit from the hole, But my question is is it possible that using any of the above options could destroy the anodizing on the job work. and is there any other easy method I can use?Please Note that the tap bit is M2 and There are no tap extraction tools for a bit that small on the internet (or Locally Available in India) but if you find one Please post links for the same. Please Be Positive and make this community a happy place. Thanks.

Topic by _Boltz_   |  last reply

### HELP - Arduino - "Expected constructor, destructor, or type conversion before '(' token"

I have only just received this Arduino UNO and am trying to teach myself the language. I thought it wouldn't be that bad as I am already familiar with python, however, I was getting loads of errors (most of which I have managed to solve from searching through forums) and have landed on this one. I get this error - "exit status 1 - expected constructor, destructor, or type conversion before '(' token"This is my code...int ledPin = 0; //declares all different pins for different segments of displayint ledPin1 = 1; int ledPin2 = 2; int ledPin3 = 3; int ledPin4 = 4; int ledPin5 = 5; int ledPin6 = 6; int ledPin7 = 7;int inPin = 5; //declares analogRead pinint alphaValue = analogRead(inPin); map(alphaValue, 1, 1023, 1, 4) //maps 1-1023 to 1-4void setup() { // put your setup code here, to run once: pinMode(0, OUTPUT); //declares pin types pinMode(1, OUTPUT); pinMode(2, OUTPUT); pinMode(3, OUTPUT); pinMode(4, OUTPUT); pinMode(5, OUTPUT); pinMode(6, OUTPUT); pinMode(7, OUTPUT); pinMode(5, INPUT); #define low digitalWrite(ledPin, LOW); //defines 'low' digitalWrite(ledPin1, LOW); digitalWrite(ledPin2, LOW); digitalWrite(ledPin3, LOW); digitalWrite(ledPin4, LOW); digitalWrite(ledPin5, LOW); digitalWrite(ledPin6, LOW); digitalWrite(ledPin7, LOW); }void loop() { // put your main code here, to run repeatedly: if(alphaValue == 1){ low digitalWrite(ledPin, HIGH); digitalWrite(ledPin1, HIGH); digitalWrite(ledPin7, HIGH); digitalWrite(ledPin2, HIGH); digitalWrite(ledPin5, HIGH); digitalWrite(ledPin6, HIGH); } if (alphaValue == 2){ low digitalWrite(ledPin1, HIGH); digitalWrite(ledPin5, HIGH); digitalWrite(ledPin4, HIGH); digitalWrite(ledPin6, HIGH); digitalWrite(ledPin2, HIGH); } if(alphaValue == 3){ low digitalWrite(ledPin, HIGH); digitalWrite(ledPin1, HIGH); digitalWrite(ledPin5, HIGH); digitalWrite(ledPin4, HIGH); } if(alphaValue == 4){ low digitalWrite(ledPin, HIGH); digitalWrite(ledPin1, HIGH); digitalWrite(ledPin5, HIGH); digitalWrite(ledPin4, HIGH); digitalWrite(ledPin6, HIGH); digitalWrite(ledPin7, HIGH); digitalWrite(ledPin3, HIGH); } }

Topic by LOU_DEW747   |  last reply

### US vs UK flour

Curious observation from my mother's recent 3 months in the USA, she says she is unable to bake well when she was in the USA. Now, given mum is a pretty amazing baker on this side of the pond,  I am wondering why that might happen ? I wondered if  its "American flour", as opposed to "UK flour" - the recipe, would be the same kind of things, memorised over the years, like a simple scone, fairycakes, pastry.  Her main complaint was that items didn't brown, even at the same oven temperatures as she uses here, and after repeated experiments with the same recipes.

Topic by steveastrouk   |  last reply

### Help! mouse is being stupid!

HELP! My mouse has a clicking problem. In that; whenever i try to click, it doesn't work, and i find myself having to click multiple times with some force in order to get a result, but it's not consistent. Sometimes, it works straight off, and sometimes it takes upwards of 20 clicks, in order to get my computer to do anything. The problem's also isolated to only the left button, the right one's fine. I reckon it's just dirt or something in the mouse, but it's really inconvenient. Any ideas on what i can do to fix it? can i fix it? To give you something pretty to look at, here's a brass cog: Thanks for all the replies. I've just had the case off, and cleaned the rollers. I looked at the switch and there was no dirt packed around it. I clicked the switch without the case on and it still didn't work, which leads me to believe that it's actually the switch that's damaged, and therefore it's not worth trying to fix.

Topic by Vendigroth   |  last reply

### waterproof material?

Can someone tell me what material I can buy that is lightweight, molds like clay, is waterproof and singeproof, and won't break the bank? does such a miracle substance even exist?

Topic by Karv   |  last reply

### K'nex M4 Carbine

About time I made an M4 carbine. The farthest shooting/accurate and sturdiest gun i've made to date mostly due to the muzzle loading. WHAT!!! NO MAGAZINE!!! yep, it was abandoned due to horrible range and often jams. It's more of a sniper than an assault rifle and is extremely accurate with a grey rod + grey connector. It uses a modded dsmans barrel for maximum accuracy and distance, accuracy due to the barrel going through the forgrip. I also added a 4-railed foregrip for attachments such as virtical foregrip (shown in pic), bipod, dot scope, lights/lasers, or anything that can attach. Tell me what you guys think.

Topic by Trauts   |  last reply

### I am looking to find out how to convert any letter or image to look like a cut stencil for marketing purposes.

Does anyone know how to convert any letter or image to look like a cut stencil for marketing purposes. I have attached what it is I am trying to do. I have cricut designspace and inkscape.Any help would be appreciated.

Topic by kprescod   |  last reply

### Pinterest image rotated, bug?

Anyone having issues with images rotating when they try to share in Pinterest? When I try to share, some of mine have their images rotated 90 degrees. Attached a screen shot. Anyone know a solution to this? I emailed support to see if they have some suggestions.

Topic by jpmarth   |  last reply

### Will replicate any gun*

Topic by TheDunkis   |  last reply

### Polishing small or very detailed metal parts - the easy way ;)

Topic by Downunder35m   |  last reply

### Arduino or Teensy coil winder - any code already out there?

I am in the process of deciding on a normal 8bit Arduino platform or a Teensy for my coil winder project.A found some interesting projects online, some with the code available too.But I was wondering if someone already implemented more than just winding a coil in such a project?At Krux.org is a nice winder based on a normal Arduino while the Alba winder uses a Teensy already to gain more precision and speed I guess.Misusing some printer or CNC code to be able to generate coils by G-code sounded nice at first but turned out to be more complex than actually required.My goal is actually rather simple despite the size and all, so let me try to explain what I want to be able to do:Have a modular winder setup so basically any winding task can be done with just two stepper motors.One for the spin, one to position the wire.Additions like limit switches and external counters are nice but usually not required for such a task if the the code is properly done.As a basic winder like all the examples out there it should be possible to just enter the wire diamter and number of turns and then push a button to wait for the finnished coil.In theory things like pitch or spacing can be calculated externally and then entered as a fictive wire diameter but of course this would be not user friendly enough ;)For special RF coils it is often required to keep an even turn spacing as well as creating a coil with many layers.So far I have been unable to find any usable code for this purpose that does not require glue, guides or at least waxing the wire.Although this seems to be simple enough, when adding things like a display and counters it soon starts to get messy with timings and steps.Is there anything out there that works properly on a 8bit processor with reasonable speed?Originally I wanted to use an OLED with touchscreen.This turned out to be too much for the timing on a Mega.Without messing around with timers and interrupts it seem a 20x4 LCD is the only option.Even then the refresh must be in sync with the tart of a new turn as otherwise the motors miss some steps here and there.These things run a 3D printer or little laser cutter with ease, so I am definately doing something wong with my approach here LOL

Topic by Downunder35m

### 3D Printer Thermistor in a K type thermocouple

Hi all,Quick question before I butcher something unnecessarily.Can I connect a bog standard thermistor as found in Chinese 3D printer (of which I have spares) to a k type thermocouple plug (I have none) and use it in my k type thermometer?Or should I just buy the slightly more expensive correct lead?I want to monitor temps @ the heat break of a new hot end.

Topic by Squibo   |  last reply

### Going to sleep with HP monitor

So I am trying to help my grandparents fix there computer, they have a dell pc ( don’t know what exactly ) and a hp 22cwa monitor. The monitor will stay on in tell I plug the hdmi in then it says no signal then goes to sleep mode, I have tried new mouse and keyboard on the computer, as well as using another cord on this monitor and pc but neither work. I did take the monitor to my pc and used the same cords and it instantly worked with both cords just fine. Before today this monitor has been working for almost 6 months with no problem and now is randomly doing thos

Topic by huongrio   |  last reply

### Plushie: CAD program for Stuffed toys and Inflatables

This is an awesome tool for designing teddy bears, stuffed animals, and big inflatable items with complicated shapes. It's called Plushie, and it looks incredibly easy to use. It's kind of like Sketchup, but for blobs of stuff. You just start drawing in 2D, and it makes smart guesses at the volume that you're trying to create. Once you're done, it generates the pattern for you that you need to cut out. Here's their cool video: It's a Java-based Windows app. Someone should definitely make something with this!(I found this via the We Make Money not Art.)

Topic by nagutron   |  last reply

### Split Tesla coils anyone?!

I am collecting data in the form of old pics, patents, newpaper and magazine articles as well as just doing things.Tesla coils are fun but is anyone experimenting with the original "multiplying transformer" that Tesla created?And before you say, sure I have a Tesla coil......I mean:Large diameter primary coil with one part of the secondary in very close proximity while the other half of the secondary is located at the center ;)

Topic by Downunder35m   |  last reply

### Find or How to Replace Old Dried Out Gaskets in a Set of 4 Ceramic Kitchen Canisters

We have a set of 4 ceramic kitchen canisters that are so old the foam seals, or gaskets, have dried out. I cannot find replacement gaskets anywhere. They were made by an individual, so there is no company to write to for replacement parts. Does anyone know who sells such gaskets? Foam or rubber or silicon will work.Or, is there a way of making replacements? I've seen amazing things done on "instructables" with silicon; molds, fake heads, toy octopus, etc. But I have never worked with it. Is it OK for a seal that will be in close proximity with salt, sugar, flour?The canisters are glazed ceramics that some individual has made.Attached are photos of the canister, mating surfaces, and existing gasket.Any suggestions will be appreciated.Thank you.Phil Brown, Southwest Wisconsin

Topic by oghk2000   |  last reply

### Looking for Used Lighter

Looking for used disposable lighters, preferably bic, for an art project for class about sustainability. Any size will work. please let me know if you have some I will be happy to pay for shipping.Best,Spins

Topic by jspins123   |  last reply

### Chaining 4 74HC595 shift registers together

I have a question about chaining 4 shift registers together.I am going to be sending data to four shift registers and my question is this, when all four are loaded and latched if I send more data is it possible to only send data to the first register in the chain without the others losing their values?

Topic by mbcharney   |  last reply

### The indestructable bike lock! ...Idea

The indestructable bike lock: the forum topic that was posted undeniably just to annoy the future patenters!So I had this weird idea for a product come out of nowhere. Y'know how aluminum is supposed to make cutting wheels on an angle grinder gum up, stick, and shatter - when trying to cut it, that is? I was wondering, what if a company engineered a special type of aluminum alloy or a similar material that would do just that: gum up abrasive cutting wheels and make them stick/bind and shatter. Then like with layers of plywood, it would be sandwiched together with hardened steel, in the shape of a U-lock bike lock, making it: Impossible to cut through with a hacksaw, reciprocating saw, TCT bladed portaband , because it's hardened and would wreck the teeth. Impossible to cut through with an angle grinder or rotary tool with an abrasive wheel because the aluminum would gum it up. Impossible to cut through it with bolt cutters - obviously... Impossible to freeze it with freezing gas? I don't know. I heard that's what thieves do. Maybe that aluminum alloy would be a super-insulator and wouldn't allow the hardened steel layer to freeze and become more brittle?I think it might just be invincible until the portable cordless battery powered waterjet is invented!Thoughts?

Topic by Yonatan24   |  last reply

### Slip ring

I am looking to build a rotating electrical connector, better known (in the electrical world) as a slip ring.The basics (my layperson terms) would include a stationary ring (fed by a power source AC/DC) and a rotating ring having 2-4 connecting points being in direct contact with the stationary ring allowing for power to be supplied to moving (rotating) devices connected to the connection points of the rotating ring.

Topic by Bill Haas   |  last reply

### Has anybody tried painting LEDs?

Because the colors available just aren't enough and we want more. *glances at collection of smt LEDs then at collection of nail polishes* The odds of me blowing up an LED or setting something on fire are slim, right?

Topic by aliasjanedoe   |  last reply

### Cheap ideas

Looking for cheap ways to make something out of tension wire spool.

Topic by DUMB8   |  last reply

### Making a water heater from a soldering iron?

I have got a soldering iron  of  60W, (with a damaged tip). And the main purpose of this project is to make a low power water or coffee heater with things you already have.  Im not a tech savy, but i know that the iron has a 2 pin socket. So, if you dip it directly in water, u'll get a shock if you touch the water. Another modification is needed- the heating rod.  the rod is made of crude iron, which can easily rust, and the tip has some leftover solder, which can poison the coffee.  can someone help in this?

Topic by arnab321   |  last reply

### Advice needed on adding a Wind Turbine (generator) to a DIY PV Solar System.

I have bought a 12 volt FD-300 300 watt wind turbine to add to my 12 volt DIY solar setup. The solar setup consists of 3 home made 70 watt panels on a single axis tracker charging 6x 12 volt 85 ah batteries wired in parallel (510 ah total) through a 20 amp controller. I run a 12 volt fridge/freezer (120 liter) and my now 12 volt (was 240 volt) evaporative air cooler (cools our 3 bedroom house) off the controller load output. The wind turbine has an inbuilt regulator. The instructions for the wind turbine tell me to attach it's + and - wires directly to it's own dedicated terminals on the battery bank. This is of great concern to me. How can this be done when the batteries are already connected to each other and to my systems controller? If it can be done without damage to the batteries would I still run the appliances through the load output on my controller? Would the different charge limiters cause an issue? My controller cuts out at 13.7 volts while the turbines controller would want to allow a charge of 14.1 volts. The two controllers also have different lower limits. As you can see I'm confused and in desperate need of quality advice. Thank you for taking the time to read this.

Topic by Rob Patterson   |  last reply

Hey guys it's me again, and I got a problem! Looking for some advice again! When I'm at school pretty much everything is blocked with this surf control and it says access denied. How and is there a way that I can bypass this?? NOTE: I HAVE ALREADY TRIED PROXY'S

Topic by rickick   |  last reply

### Led on in sequence one by one

I want to make a circuit to turn on all led one by one. I tried to do it with 4017 . But that ic turn off the previous led but i want to tun on all led one by bye in sequence.

Topic by HoneyS26   |  last reply

### Compact ight sensor switch with low voltage

Hi there,I've got a led light that's operated via a magnet, if it doesn't detect a magnetic field it turns on if it does it turns off. It's a led light for car door(check picture for reference) and uses 3x AAA batteries in my case 1.2v x3 (3.6v), if you use regular batteries it's 4.5vBy mistake I've order a tiny light sensor module 3.3-5v(check picture) which obviously can't be used as a switch, not in it's present form. While I'm good with solder, I've build an ebike, I'm a computer guy but when it comes to things like this like this make me feel powerless :( ..I 've used 12v light sensor switches but that's a different topic.So, how can I have a low powered light sensor switch that's compact and can save me from replacing the batteries frequent? ...the led light turns on even at daytime which has no point in doing that. I'd appriciate any help :D

Topic by Takisk1   |  last reply

### Dual timer switch

Is there a commercial dual timer switch that the first timer can be set for longer duration like hourly or half hourly and then switch on another timer that run in seconds. Or is there a DIY solution? Eg. Turning on a water sprayer every 2 hours for 10 seconds. I need a timer that run from the mains.

Topic by TanJ21   |  last reply

### Will pay someone to make this for me.

Https://www.instructables.com/id/Counter-Strike-C4...I want to make this but I'm missing alot of the parts needed to do this myself. So I'm paying anyone who can make one look as close to the ones the others have made with working LED and everyone.

Topic by razz5   |  last reply

### Ethernet selector between 4 different sources

Hello, I'm trying to design a switch box to switch between 4 different ethernet sources and output to one cable. I've checked around and believe I have developed a way to do it, but I am unable to find a switch that uses 4 smaller independent switches. The concept seems pretty straight forward but I don't want to use 16 switches. Please let me know if there is a switch which controls 4 independent connections or if there is a better way that I'm over looking. I look forward to your input! Best Regards, Zach G

Topic by lossofworth   |  last reply

### Rotating multi-layer Face scupture

Hi I would like to make a diy small scale version of the following video.https://www.youtube.com/watch?v=8yQ4Pscb-ZQ Preferably a Lord Buddha head version of it. I am pretty creative but not mechanically inclined.challenges are as follows:_1) how to get a 3d scan of a buddha head i already have 2) cut the 3d scan horizontally in multi layers3) make a small scale model4) make the different layers rotate and control individually5) make it artsy...i am good with that so dont need much help

Topic by rav527   |  last reply

### Replies to Message in my Inbox does not show up in Mobile view

Mobile: Android. Browser: Chrome.When someone sends me a message on Instructables, it shows up in my inbox. When I reply to that message, it doesn't display it below the recieved message. Although the replied message does show up in the Sent section.#Feedback #Bug

Topic by Jonathanrjpereira   |  last reply

### Hi, I'm New :)

I was a simple man, love hardware, but never knew how it works.However, a good friend of mine gave me Arduino nano.since I do not know anything about the dev, I would like to gather some info, ask questions for developing, coding and others.So, heyyyy Im new, teach me senpai(s)!

Topic by Wario_Bros   |  last reply

### Where can I find Recycled Pet Felt sheets?

Where can I get completely recycled pet felt sheets. Would require them in large quantities for development of furniture. Is there any option in India?

Topic by bedraj.tripathy

### Need help building a small extension for my desk

I got a microphone arm that clamps down to my desk ( can be seen in the picture) but the problem is that it's right in front of my mouse. I have to have it folded it up because it does not have to be extended since it's right there. It has gotten annoying after a while and I change it to hang from essentially where my window is ( also shown). my desk is has drawers and doesn't have any edges to clamp it down to so I was thinking if I can make a short extension for it. I don't need a whole new section I just need a secure extension that can be used to sustain the weight of the arm and mic. I tried drawing it and I hope it helps showing you guys what I envision. Thanks!

Topic by Crux_Yo   |  last reply

### A rewiring electric scooter issue

WHEN I REWIRED MY EZIP 1000 ELECTRIC SCOOTER, NOTHING SEEMED TO WORK BUT WHEN I TWISTED THE THROTTLE THE POWER SWITCH LIGHT CAME ON. IT WENT OFF WHEN I RELEASED THE THROTTLE. WHAT DID I DO WRONG?

Topic by floridianskin   |  last reply

### Things you can craft from (Recycling!)

Here is a list of some great things you can craft things out of:CARDBOARD:-Empty Shoe box-Used Poster boards-Empty Dunkin Donuts Munchkin or Doughnut box-Empty Pizza BoxesCONTAINERS:-Empty Altoids candy box-Empty Water bottlePAPER:-Newspaper-Used Paper (like one you used to write phone numbers on)PLASTIC:-Empty water bottles-Empty milk containers*Adding more soon!*

Topic by dragonblue80   |  last reply

### We should have a Back to School Challenge!

I think that this would be a great, fun, and relevant contest for the months of August and September.

Topic by jseely23   |  last reply

### Would a small scale model of your own house fit in the theme the Tiny Home contest?

Question for mods. Sorry if this is the wrong spot.

Topic by DIYJRAY   |  last reply

### Calibrate Compass

I have compass cmps-12 and i want to use it or calibrate it with my raspberry pi 3 using python. I already check on website but im not find it how to make it work. Please anyone knows how to calibrate compass cmps using python on raspi3 i need your help. :(

Topic by alharis   |  last reply

### Construction of a robot learning to move in internal rooms

I am looking for a person who knows how to make a robot that will move inside the space, avoid obstacles and create maps of the rooms in which he works?

Topic by finder11   |  last reply