2WIRE / WiFly Issue

Have WiFly Shield, Uno, 0022, current libraries. 2WIRE router is set WEP-open DHCP: On. Am Using gateway.2WIRE.net and IP scanner to check connection. Cannot get WiFly to associate/connect. I have the Roving WiFly GSX manual and tried dozens of configurations to no effect. The only thing not working is the acceptance of the WEP encryption key. 2WIRE has a 10 ASCII key while Roving requires a 13 ASCIIt key I get the following message: Set security phrase to xxxxxxxxxx (my 10 digit code) set wlan key xxxxxxxxxx Bad len=10 ERR: Bad Args <2.23> Any way around this?

Topic by tedlawson 


Cannot get WiFly to associate/connect to 2WIRE Router.

Have WiFly Shield, Uno, 0022, current libraries. 2WIRE router is set WEP-open DHCP: On. Am Using gateway.2WIRE.net and IP scanner to check connection. Cannot get WiFly to associate/connect. I have the Roving WiFly GSX manual and tried dozens of configurations to no effect. The only thing not working is the acceptance of the WEP encryption key. 2WIRE has a 10 ASCII key while Roving requires a 13 ASCIIt key I get the following message: Set security phrase to xxxxxxxxxx (my 10 digit code) set wlan key xxxxxxxxxx Bad len=10 ERR: Bad Args <2.23> Any way around this?

Question by tedlawson   |  last reply


AT&T WiFi connection problem, help asap please!!

my computer and ipod touch seem to be fighting each other ip address wise, when one connects to the internet it steals the others internet connection and after a few minutes the device loses connection altogether. I've already set both devices to have private fixed ips .68 for one and .69 for the other. another thing is that when only one is connected on the 192.168.1.254 mainpage the device says it is the other, so when my computer is connected but not my ipod it says my ipod is connected and vise versa. my main problem is they lose connectivity after a few minutes. i have also disabled the wifi protected setup(which att told me would help solve my problems). If any other info is needed please tell me, i really need this solved!!

Question by miiwii3   |  last reply


Home made charger for a cordless. screwdriver.?How do i connect 2wire charger to 3 prongs on batt.

Blk & dec vpx 7 vdc cordless screwdriver.Missing charger,not available anymore.Batt. has 3 prongs for charger.

Question by    |  last reply


How to improve wireless connectivity using AT&T

I have an AT&T 2Wire modem with wireless connectivity, but the signal is entirely inconsistent with both the wired and wireless connections. I am certain that it is from using DSL, but am open to suggestions as how to improve connectivity and speed.

Question by gmjames   |  last reply


I have an AT&amp;T wireless router now that i switched to armstong cable do I really have to buy a new router?

I have tried a few different things and I cant get the thing to work the 2wire ethernet and wireless lights are green but the DSL and internet light just keep flashing red. I dont understand why it wont work. Cable said it may but wouldnt even try it they said just go buy a new one. Can anyone tell me how to make it work.

Question by LindaD.   |  last reply


Too many electronics sitting around

I have too many electrons sitting around and was wondering what all I could make with them? Heres the list to what I have: a brand new 2wire wireless router 2700hg-b a dead creative zen stone 1gb 2 old digital cameras - 1: sony cyber-shot dsc-p52 - 2: hp photosmart 435 64 mb sd card 16m MMC 4 cellphones - 1:Samsung Qwest SPH-A880 - 2:Sony Ericsson W300i - 3:LG PM225 - 4:Sony Ericsson Z520a (all have batterys not sure if they work though) old xbox 400w power supply usb external floppy drive im sure there is more stuff ill add it in later if I find anything else

Topic by JRauck   |  last reply


I thought I knew how to run 5e in 4 rms and have a hard internet connection in ea. at all times & it don't work,need HLP

I'm just learning about computers,internet, and I thought networking. I have a At&t 2wire DSL. It is in the master bedroom. I ran a loop to 3 other rooms with 5e cable. I put to jacks in the wall seperating the runs from room to room. My thought was I could just use a patch cable to configure the network at anytime if I moved the DSL unit to another room. Right Now I can only get the computer in the masterbedroom directly connected to the DSL unit and one other in the bedroom. I have 2 laptows working using the wireless just fine also. The other that is hardwired and working in the bedroom I ran a cable out of the 2wire unit to the jack in the wall in the master bedroom and throught the 5e I installed in the wall in the one bedroom. All that works. I tested the other 2 other rooms and they don't work. I guess my installation of the 5e in a loop to all the rooms was incorrect. I don't know anything about networking, ect. I'm just trying to learn and now I need to figure out how to fix my problem where I can have a computer in all 4 rooms working on the DSL. I'm hoping someone will tell me I didn't waste all the time and money the way I already ran the lines. I don't know how to fix it and I found this site and I'm hoping someone can tell me how. I used to be a electronics tech. many years ago and I have reciently had my brain fried from radiation because of the cancer that was found in my head and neck. So, I'm not all here and I'm getting better but it is really hard to do the logic right now. I'm hoping someone can help. Thanks in Advance!!! Dave

Question by DavidTipton   |  last reply