Can someone convert a text document into a program. If you tell me your email I will send you the text document.
Question by neeley | last reply
Help! I am way into BASIC. Lately, I have been wanting to make a little DIY pocket computer with a basic gray scale screen and nav buttons that can run simple BASIC programs uploaded from my computer. I looked around Google to find somewhere to start, and found out that no one has ever attempted building such a thing before. One site suggested that I should look at mobile motherboards by TI and Atmel. However, when I arrived at the websites, I found a bunch of complex, expensive boards that have unnecessary fetures such as WiFi and touch. I need some help on what hardware configuration to use (aka mobile motherboard, chip set). Help!
Topic by akchicken | last reply
Is there a website to learn about how to use picmicro's really easily? I realize that there are some instructables about it, but to be honest they arn't very helpful. For example, I have no clue what the crystal does, why you need it, how to hook it up, and how much voltage they need because I need to buy some.
Topic by guyfrom7up | last reply
I probably know more about sewing as far as hands on, visual stuff, but lack vocabulary. As such, a verbal, or wordy description doesn't help me much. Is there a good site for novices to learn more? Or are there specific -ibles for those of us who don't know a ball point needle from an inseam?
Topic by Toga_Dan | last reply
I am a beginner to the Arduino field can you please help me with these questions ? How many smartphones can communicate with a single Arduino at a time? How many Arduino a single smartphone can communicate with at a time? How many devices such as AC TV and lights can be connected to a single Arduino? Is voice/noise isolation room affects Bluetooth transmission (if my phone connected to the Arduino using bluetooth)? In case of smartphone outside the room containing the Arduino. please if you have any references or links that might help with understanding the main concepts please help..
Question by maryamCS | last reply
I purchased the Arduino Basic Kit a number of years ago. The directions say to go to Autodesk.com/Adruino to get started, but that page doesn't exist anymore. Does anyone have a PDF of the project directions for the parts included with the kit? Thanks.
Topic by bryan.thatcher | last reply
I brought 5 RGB LED's just now on the interweb, but I have no clue about circuits all I know is theirs parallel circuits which I will be using and I have a power source of 2 AA batteries. Sorry for such a newbish question, any links to and learning articles would be greatly appreciated.
Topic by Antexter | last reply
Hey I got Atmel ICE basic, 6 pin wire and atmega1248. I try to sent program code, but there comes error message. How I should connect pins? http://www.atmel.com/Images/Atmel-42330-Atmel-ICE_UserGuide.pdf http://www.atmel.com/images/Atmel-8272-8-bit-AVR-microcontroller-ATmega164A_PA-324A_PA-644A_PA-1284_P_datasheet.pdf
Question by mattilaniko | last reply
Hi all. I am making a CPU benchmark program in Visual basic Express 2010. I have everything I need except the actual STRESS TEST. :D Heres a BASIC look at what i'm thinking i'm going to need. Private Function StressTest() As Integer 'Complex math that will STRESS the CPU a lot math.math.math............................ math math math................. 'Complex math that will STRESS the CPU a lot return time-taken-to-run-test-in-mili-seconds End Function Please help me make this! I am SOOOOOO Close! All I need is to know how long the thing took, and the actual math that puts STRESS on the CPU!!! PLEASE HELP ME OUT!!! IT WOULD MAKE A 12 YEAR OLD'S DREAMS COME TRUE!!! THANKS!
Question by sci4me | last reply
I am making a box that when opened will sound an alarm. When it is closed, the contacts are touching, thus completing the circuit. When the box is open they are not touching. How can I make a circuit that will realize when theyre not touching(without using an Arduino or other programmer)???
Question by crocboy | last reply
Hello all! I'm beginning down the route of hobbyist electronics. As to basic safety precautions I'm really quite unsure. I know inside many electronics parts and devices (For example, a TV one would strip for parts,) there are many nasty chemicals. I don't want to get lead poisoning or any other sickness. If you could point out some safety precautions, I would be incredibly grateful (Ex. Always wear gloves, wear a mask when soldering, when stripping a TV...., etc.). Thanks for your time and help!
Topic by I Am That Guy | last reply
Hello instructable forum. I had a qick question about a project I'm thinking of doing. So I wanted to make a poker table. I know how I'm going to do that, but I wanted to make a built-in dealer chip. So I was planning to put 8 LEDs (One for each station/person) And at one station there would be an Push button. I want one LED to be lit up at a time, and when the button is pushed, I want the power to transfer to the LED to the right of where it previously was. Again: I only want ONE LED to by lit at a time. I'll include a basic pitcure for a visual. I think I'll need a demultiplexer and a counter, but not too sure how to use them. thanks, Jusstice
Topic by Jusstice | last reply
Hi there I have an idea in mind and would like to know if you guys think it would be possible to make. The object is for the battery to last a minimum of 150 hours of constant use. I want to use the smallest possible LED say 2mm or even a SMD will be sufficient, the led must run off a very small battery either a LR44 / CR1225 or something similar in size and the design must have an on off switch. Do you have any suggestions? Is this even possible? Any ides? Thanks Matt
Topic by b1g5l1ck | last reply
Hi guys, recently I thought that what if i make an rc car that charges while I use it outside in the sun, that way I can use it as much as I want (outside in the sun) and I wont need to charge it. I have attached a picture showing the wiring, but I have a few questions. Q1. Will it work?? Q2. If it does than what will happen when im not using it and the solar panel uses the light in my room and overcharges the battery resulting in it catching on fire? Q3. Would it be better if i replace the car battery with rechargable cells? Help with be greatly appreciated :) Oh and don't mind my grammar, its not very good hehe UPDATE changed diagram, will this work?
Question by The Prickly Potato | last reply
Hey Guys, Today I made one of the simplest circuit I have ever made, its literally two motors in parallel with a switch. The problem is it didn't work :( (embarrassing). I don't know what I did wrong. When i flip the switch the motors just spins for 1 microcentimetre then stops. I even attached an led to the terminals of the motor it just blinks once then turns off till i flip the switch again. Anyway wiring and demonstration is in the pictures, videos provided. Here are somethings to note: 1. The motors were working perfectly before i made the circuit. 2. The battery (may) be half used. 3. The glue used to attach them to the base (styrofoam) is hot glue, so I had to be verryyyy careful to not melt itithe base). 4. I cant take it apart since its attached to the base and the base will break and using glue with styrofoam wasnt easy so I dont want to do it again. 5. I have tried even by moving the motors a bit away so that they dont touch, still doesnt work. 6. If I leave it on for say a minute the battery gets slightly warm to the touch. 7. I cant find any short in the circuit.
Question by SA-DIY | last reply
I have a list of the basic tools I will need for this. If you can add anything that would be great. 1.LEDs 2.Wire 3.Duck Tape 4.Soldering Station 5.Persision Screwdriver 6.Razor Knife 7.O-Rings 8.Springs 9.Batterys 10.Needle Nose Pliers 11.Clamps 12.Screwdriver Any other suggestions would be great. Thanks.
Topic by amature engineer | last reply
I am in the process of learning SolidEdge V19 by myself (It's CAD program, if anyone is wondering). Now I know it may not be the best place to start learning CAD, but I got it for free. I am quite new to CNC machining and CAD software and I need some clearing up on a subject: In what environment do I need to draw the parts in order for it to be used CNC? I am only working with sheet metal and have all the precise dimensions of the parts that need to be cut out. Should I create the parts in the drafting environment and then export it as a .dxf file which will be used on the CNC? Sorry if my question sounds a bit, you know, stupid, but I just need some clearing up on this issue.
Topic by SirMalan | last reply
To whom it may concern (mainly the ones who chose to blast my consern about the pop tab chainmail armor). Have You people forgotten the fact that as a species humans are incredably stupid??? I know My spelling is not dead on, Please forgive Me! I have to quote Tommy Lee Jones from M.I.B. 1. " A person is intellagent (?), People are dumb, paniky(?) animals. And You know it!" I could just see a newbie log on, find that information, build it and expect it to protcect them at the next S.C.A. event!! The Terry Pratchet comment was totaly funny and true!!(I am a true madman.) Thank You for noticing!!! I was only trying to help! Maybe others should also!!! Thank You!! Roy Smith.
Topic by Roy smith | last reply
So... before I start... I am not a physicist, nor am I an electrical engineer. Hopefully someone within one of those (or both) professions will chime in and enrich this discussion. That said... I'm going to be using leyman's terms. This thread is specifically meant to explain how a brushless DC electric motor exerts a force, and how that force is used to generate work. To start off, I'd Like to explain the components which comprise a brushless DC motor: First... You have an axil. The axil's purpose is to spin. Next you have natural magnets, or solid state magnet; I use the terms somewhat incorrectly, since a natural magnet refers specifically to nickel or ferrous base magnets, but there exist a large variety of compounds and composites that exhibit the ability to produce magnetic fields. In practice you have many in a motor, but for our purposes... we can pretend we have one. The natural magnet's job is exert a magnetic field while attached to the axil. After that we have an electrical coil. Once again, in Brushless DC motors, we have many of these, but for our purposes we'll use 3. The electrical coil's job is to produce a magnetic field which can move in a circle. Finally we have the engine housing. The purpose of the engine housing is to hold everything together. Note: I'm intentionally leaving out the computer control mechanism. there are alot of great instructables on microcontrollers. Most Brushless DC motors requrie one to work since there is no mechanical timing device, as there is in a brushed engine. So... how does this fit together? In this setup the natural magnet produces a force when next to the electrical coil (This coil is also known as an electromagnet). This is because the charge of the coil is opposite to the charge of the natural magnet. Once the Natural magnet and the electromagnetic coil align with each other, the first coil shuts off and the second turns on. Once again the natural magnet is drawn towards the magnetic pole. This process repeats until the natural magnet has spun in a circle (note: usually you want it to continue to spin beyond a single revolution.) That's the basic (very basic) idea behind a Brushless DC Motor.
Topic by Qcks | last reply
Hi there im interested to know if any body has the brain and know how to make one of these http://www.core77.com/blog/wearable/durr_the_vibrating_watch_from_skrekkogle_that_sort_of_tells_time_26234.asp could be a cool project Kind regaurds John Cook
Question by johncook-2 | last reply
Hello everyone i'll try to keep this short and sweet. In my next project I will be re-Building a trolling motor. The trolling motor runs on a 12 volt battery, and draws between 5 to 30 amps. The problem I have is that the control unit/head of the trolling motor is destroyed. In other words all i have at this point is a 12 volt motor connected directly to a 12 volt battery. The trolling motor is very powerful and I don't want to run it full power all the time. This made me look for a 30 amp dimmer switch, just like the ones people have in their homes. With no results I don't know what to do. I am thinking about using a 600 watt AC dimmer switch like the ones in peoples homes, but I don't know if it will work with a DC circut like the one I have. Thanks for your time and help. ~KayakKid
Question by Kayak Kid | last reply
I'm trying to make a program that will keep track of my emulators and roms and some information about them. i'm a beginner and i was wondering what i need to use so i can make the database or if there's something else i can do, Thanks in advance for the help
Question by coldpsyco91 | last reply
What do I do to turn a text document into a program written in BASIC
Question by neeley | last reply
I'm making a couple of programs in Visual Basic 2008 Express Edition, however once you publish it the files are darn hard to distribute. If you move it it won't install correctly and if you ever try uploading 3 files to a webpage asking people to download all of them they're likely to just ignore you. So I would like to be able to mix all those files into one single self-contained .exe file which can be copied or moved as much as the user wants. Can I do it? All help is appreciated.
Question by awang8 | last reply
Can anyone recommend a book/website where I might learn the basics of electronics? As basic as possible would be nice. I'm just tired of seeing wonderful things on this website I can't make because I don't understand the first thing about voltage, etc.
Question by 5m17h | last reply
I would like to learn old school BASIC. The parallax basic stamp uses it's own version of it called PBASIC. I have not found any current books that will teach you a foundation to build on. I looked into programing for the absolute beginner and programming for dummies, both books seem to treat (teach) Basic as an object oriented language and jump into making window with buttons. That's not what I need right now. I want to start BASIC with the basics (forgive the pun), i.e. loops, if then statements and build a foundation . But I really need to start with BASIC so I can get the best use out of my BOE bot. PLEASE DON'T SUGGEST C OR SWITCHING TO A DIFFERENT PIC, I don't have money for that. All the parallax labs are in PBASIC.
Topic by Omegablood | last reply
Hi all! I just found a parallax basic stamp at a price I couldn't really resist. Now I am wondering if anyone who has worked with these micro-controllers knows of a good guide to learning the programming language that is free or rather cheap. Thanks for your time! :)
Question by thegeeke | last reply
I need to make a basic fm antennae for my reciever inside my mancave, It's a steel shed converted and inside reception drives me crazy. I do have basic poles and some wire types in my arsenal. Someone PLEASE HELP. I need my music to keep my sanity if you can relate.
Question by gday85208 | last reply
What are some some light ideas that I can use for photography without having to purchase expensive equipment? Do not want to invest in photo equipment until I make sure it's something that I decide that I want to take seriously! Hope someone can give me some helpful advise!
Question by 2di4 | last reply
I am brand new to leather crafting and just ordered a vintage stamp with 3 other tools. I think i just broke the stamp. It is flat with a hole on the back. I used a hammer on the stamp by itself and the hole looks like the ridge around it is broken. Was I supposed to put something in the hole before hammering?
Question by Jlady711 | last reply
I'm new to arduino's but not new to programming, more of a novice, so my question is more physical than logical- why does my push button say i've pressed it 4 to 7 times on the serial print, when i've only pressed it once? is my push button broken? and when i hold the push button down, the serial print says i'm pressing it repeatedly?
Question by DemolisionWolf | last reply
Ect student @ Devry here trying to put what i am learning to practical use. I reeeelay want to learn arduino it seems very fun and has a wide range of things you can do with it. Other than basics (mm solder eq resisters/leds & tools and such) what are some "must haves". Info like what board to start out with, power supplies i should acquire. Hints tips tricks, places to read would be great. I am somewhat limited on money (father of 7 trying to pay my way.) So i need to be budget minded. I have loved this site for a while and recently upgraded my membership. Some of the projects i see come from this community makes me drool. Ty for reading.
Topic by Evan N. | last reply
So, I was making this circuit and ran into some problems so I would like it if any one of you could help me. (Schematic attached) Q1. Do you see any basic problem in this circuit? Q2. Will this relay (http://zaymanta.com/media-library/stores/RALEY-6V-10A.jpg) work with 5v? I have tried this before and it works but I was wondering if there will be any problem like flickering, fluctuating or something like that. Q3. Which transistor should I use for this job? Q4. Can you check if the esistor with ldr (and rest) is of the right value? Q5. Can anyone modify this circuit so that the red led turns off when the relay is active and the green turns on (instead of both turning on)? The relay will be used to control 240v. Thanks alot in advance :).
Question by SA-DIY | last reply
I'm looking for a light that I can place on the floor that would shine onto a projector screen. Something that spins with a spiral display. Either the light itself spins. Or possibly has the ability to place a filter onto a steady light and the filter spins. I'm in a band and i'm looking for something that would be strong enough to show this light display behind the drums as we play. The light and the projector screen would be relatively close to each other.
Topic by Ellyni
Hello, If the input to the positive terminal of an op amp is 12V, the input to the negative terminal is 10V, and there is no supply voltage, the output voltage is 2V and the output current is 0. Correct? Now, what I don't understand is what happens to the output voltage and current if I connect a supply voltage of, for example, 15V. I know that the output voltage and current both increase, but I don't know the math behind it. Can someone explain this to me, please?
Question by frossiove | last reply