I heard a laser could shut down cameras. How do I know if one is used on my cameras to protect my house.
Question by Rainbow1946 | last reply
After reading this, and then this, I started thinking of how easy it would be to make a burning laser. I went to Radioshack, got some components, and started thinking. One thing that Stephanie's laser didn't have is a potentiometer, to control the power of the laser. Well, I ended up getting 12 assorted pots at Radioshack, but didn't know what one to use. I want decent control, too. What size (in ohms or k-ohms) do you think I need? I'm spotty in my electronics knowledge. PS- The size in ohms on the pot is the pot's range, right? If it says 100k, it means that it will resist from 0 to 100 kilo ohms, right?Also, in the shematic below, I don't know if the pot is connected correctly, post a comment if it's wrong.
Topic by John Smith | last reply
Hi wondering if anyone could help me have a luifure laser cutter 40w which we have just purchases software CorelDraw and laser draw 2013 came with it but the laserdraw 2013 wont load onto my daughters laptop also we did not receive a English maual with it so basically don't have a clue what we r doing any help would be greatly appreciated or we r from fmaesteg south wales so does anyone know of someone who could set it up for us thanks
Question by straddie | last reply
Hello every one. I really need some help on how to make a ruby laser, i live in Australia and laser are totally banned where i live so i did some research on how to make powerful laser. I came across Ruby laser, i did some research but i am not sure how to make one or get the parts from so any one that can help please do so. thank you. :)
Question by kk khrab | last reply
Hi, I would like to put together a laser rangefinder, with LCD display, that can measure distance to the objects out to about 600y, with accuracy of +/- 1 y. I know absolutely nothing about electronics. Can somebody tell me what components would I need? regards, dejan
Topic by COROVICD | last reply
I know scientist have created lasers that can cut but how much money would it take to make one? and what materials would be need? and... what kinds of materials would be laser resistance, not effected by a laser... or would that depend on the lasers stength?
Question by saiyankev | last reply
I have a laser diode that needs between 3.7v and 4.2v to run, http://www.laserlands.net/gd-ms-200mw-green.html and i plan to run it of an arduino (5v). to reduse the voltage i have calculated that i need a resistance of aproximately 1.333ohm. is this necessary/is there a bether way to do this? thank you in advance for any answer!
Question by ludvig.risan | last reply
Hello (excuse my English really bad I'm Belgian and French) I would like to cut aluminum sheet of + - 5 mm thick and also cut paper without "burning the edges" I would like to know what kind of "laser head" the cheapest possible exists and what would be even better, whether this kind of "laser head" is recovering ... I was thinking of a DVD laser burner but, even though I I'm as good at DIY as an elephant is good at skydiving, I guess a DVD burner will not cut aluminum ... A big thank-you
Topic by Hiram | last reply
I bought a laser engraver from Amazon and it is a Luyeen brand. It's straight from China and honestly, it's a POS. When I put it together, which took 24 hours, I couldn't get the laser to work. I looked on line and I found a forum that had someone that bought the same thing as I did. The wires that were on the connector were backwards. I took the cable to a PC Repair place and they fixed it. Now, the laser has not worked and I contacted the manufacturer and they ASKED ME to have it repaired and they will also give me $100 to compensate me for my time. ARE YOU FREAKIN KIDDING ME? NO!I am returning the whole thing to Amazon for a complete refund. So, here's the question, Folks! Where can I find an AMERICAN made laser engraver that isn't going to empty my wallet and I can afford. I am tired of Chinese places advertising GOOD products and when they arrive, they don't work, they are not as advertised and the directions are worthless. I REALLY would like to get an engraver but I will NOT be buying off of Amazon that deals with foreign manufacturers that sell substandard equipment. Can someone give me some place where I can look?Thanks, David Monaghandavidmonaghan58@yahoo.com
Question by irishwarrior1958 | last reply
Link to buy the plans to make your own (would be cool for the Robot Challenge, i am thinking about it) March 6, 2008 Stephen Hobley saw Jean Michael Jarre play his highly theatrical Laser Harp live 22 years ago and vowed heÃ¢â¬â¢d build one just like it. HeÃ¢â¬â¢s just ironed out the bugs and you can see him play it here. Whatsmore, he has detailed the entire construction process on the Internet. He reckons anyone can build one for under US$600 after purchasing his US$19 Laser Harp Plans and Source Code.
Topic by laminterious | last reply
Hey guys, I can imagine this question being asked a few times, but google did not provide good results. ANyways, I have a CD drive, CD burner, and DVD drive and wanted to build myself one of those nifty laser pointers that can burn matches almost instantly. Which one will have the strongest laser to do this with? I'm assumign either the CD burner or the DVD. so which should I tear into?
Topic by Spamwich | last reply
Hi all!So, I have been volunteering at an animal hospital in my home town, and I have been allowed to observe 11 surgeries so far, 4 of which have been performed with this 30 Watt CO2 Surgical Laser. I would like it if someone could explain to me how a CO2 laser works, and I would be willing to answer any questions. the surgeries I have watched are: (1) a spay on a dalmatian (2) an entropion correction on a bullmastiff (3)a cauterization of a bleeding tail tip (without anesthetic & with me holding the dog down!) and (4)a front declawing of a cat.
Topic by bardon08 | last reply
Help help help! Ive just fitted a 15w laser to my cnc 3018 and I cant get the laser to switch to low power mode. It just wants to burn everything! How do I fix it? Ive attached two pictures, one of the laser and one of the board. The board is a woodpecker GRBLO 9. Please if anyone can help me I would be eternally great full.
Topic by MattK171 | last reply
So im making a laser spirograph (https://www.instructables.com/id/Laser-Spirograph/#step1) and i just got my laser diode to come out of its case, and i was wondering where i should solder the red and black wire as it does not look like the one in the 'ible. the laser diode looks like this one here http://10mW 532nm Green Laser Module (3V 11.9mm) (i would take a pic of the diode but i cant find my camera!) the only difference in the diodes is that mine has a black button instead of the red. Oh and one more thing is that it has to bypass the use of the button. Thanks in advance!!!!!!!!
Topic by Mr. walrus
A member PM'd me with this question, "hi im asking if i can use the arduino micro controller in distance measuring using laser" My response was "Laser distance is the time of flight of a pulse of light pulse that travels 3 feet in a single nanosecond..." https://en.wikipedia.org/wiki/Laser_rangefinder Do you think the Arduino can execute instructions at a fraction of a nanosecond ? What is the clock frequency of an Arduino ? . Take care of your eyes when using lasers !
Topic by iceng | last reply
I recently came across a HeNe (Helium Neon) Laser module, probably from some medical equiptment. it has no power supply, but im in the process of acquiring one. Does anybody Have any suggestions for what i should do with it? it will be my first post, but definitely not my first project. i'm not accustomed to working with lasers, so any help would be appreciated. Sepcifications: 15 Mw max class 3b model no. LGK 7621 MM
Topic by nickdisney | last reply
So recently I've collected a couple 32" fresnel lenses from rear projection tv's and am curious how one( if possible) would collimate the light into a laser beam to cut materials. I've spent a few hours searching the web trying to find the information I am seeking. Even help with searching terms would be appreciated.
Topic by IamEdgar | last reply
Hey I read something somewhere about how to make a Laser from a DVD burner. Ive seen the lasers from DragonLasers and WickedLasers and I want one, but because of the price I thought maybe it would be better to make one myself.This is the DVD burner I intend to use: http://ec1.images-amazon.com/images/I/111Y366TSDL._AA160_.jpgPlease reply to make ASAP with any advice on how to do this.I am not very good at electronics or anything like that, this is the first time Ive done my own little project like this.Thanks.
Topic by Jay Dee | last reply
I am trying to create 8 motorised lasers that move (ideally randomly) between a 135Ë angle. I doubt with my level of knowledge i will be able to make them move randomly but if i can't just moving back and forth between the 135Ë would have to do.These motors would have to be reversable and travel between 2 points making an arc of 135Ë, I'm looking at making this in the cheapest way possible. By mounting cheap pen lasers onto mini motors and somehow getting them do this. I will need to see the beams of light so unless i can find a better way to used focused light cheaply, i'll have to use a smoke machine or something. Having no real knowledge of this, would it be easily achievable, i would use a microcontroller to make the motor movement random within that 135 degrees but i have no idea how i'd go about it.
Topic by happysnail | last reply
what kind of laser is used in laser printers?
Question by Fypsigon | last reply
I pulled a laser diode out of my 16x dvd burner drive and want to use it to make a laser cutter/burner. I want to know is it required to use a laser module or can I just hook it up straight to a battery and have it work.? Also how many battery do I need to make it work.? I tried hooking it up straight to a 9v battery but nothing happened.
Question by adamdarby43 | last reply
I was playing through my older Splinter Cell games the other day, and had my airsoft pistol next to me. I had attached a laser pointer on it, mostly for kicks and giggles. While playing Splinter Cell, I turned off a security camera by shooting it with some sort of laser from my FiveseveN and it gave me an idea. I decided that I'd like to make a simpler version of this for a scenario airsoft game. So my question for you guys is, is it possible to make a laser tripwire that can be turned off by aiming a laser pointer at some sort of sensor on it? If so, how much would materials cost me, and how difficult would it be to assemble? Could it be pulled off by someone with little electronic experience like myself? Thanks in advance!
Topic by CapnTac | last reply
Hi all Thinking about putting a project together based on some of the great instructables on here. Can anyone shed any light on how much power I will need for a laser that will engrave slate? I am not sure whether a diode laser will be up to the job or whether it will have to b a co2 laser. Any info would be appreciated.
Topic by gary101 | last reply
Hello everybody, I'm sorry if this is already explained in an instructable, but I can't seem to find one... My question is, is there a way to make a laser pointer from the laser thingy inside an old cd-writer or an old hard drive (that both still work) ? Thanks
Topic by Ramvan | last reply