Search for Programmer in Topics


PIC PROGRAMMER

I just want to know if there is a different pic programmer for different pic microcontroller

Topic by ipis_12    |  last reply


AVR Programmer

I am building a  AVR Programmer refering from site : http://www.fischl.de/usbasp/ So Please can any body give the  .Hex   file to burn my Atmeg8( the on AVR circuit board). Would be a great Help to me  !  ! Thank a lot - Akshay Jadhav

Topic by akshayjadhav    |  last reply


PIC12F629 programmer?

Hi all,       I want to program PIC12F629 with readymade .hex code. Which programmer should I use? I would like to know the best and cheapest programmer available. I bought PICKIT2 clone from India but I had very bad experience with it. I couldn't program with it.       Can you please suggest me good programmer? Regards, Chetan

Question by chetancc  


usb pic programmer Answered

Im looking for a schematic or instructible for a pic progrem with usb id rather make it myself though if any one know wheres there one please let me know

Question by hightekrednek2396    |  last reply


USB pic Programmer?

Ok guys so heres the deal i need a good and cheap schematics for a USB pic Programmer ive had some experience with schematics but i must admit its been a while my ultimate goal is to build a cheap good set of lazer tag thanks ps PIC18F2525 is the chip im trying to program

Question by nimbian    |  last reply


DIY programmer for PIC16F88?

I was wondering if anyone knew of a relativley simple DIY programmer for the PIC16F88. All the programmers I have come across on this site dont support it. Any help will be appreciated.

Question by XxShadowxX14  


Programmable T-Shirt

Saw this shirt and thought it was cool. They said it was expensive to make. How much do you think they made it for and do you think you could do it for less?

Topic by ehudwill    |  last reply


Programmable solenoid controller

Hi all, I need some help finding a suitable solenoid controller, it must be dc powered and operate a latching solenoid for an hour every 24 hours. It must be programmable by the user and operate the latching solenoid instantaneously on and then off separately. It should be relatively cheap as its for a HNC lawn watering project. Regards woody.  

Topic by woody1001625    |  last reply


how to programme a PIC16F84?

While programming a PIC16F84 do we have to enter the hex file or asm file or any other

Question by robot1398    |  last reply


Programmable LED Sign

Ok, Today I bought a LED sign for $10, It is the old programmable type, Problem-It takes 9 volts AC, at 30 Watts. Which is a LARGE problem.......I cant seem to find a transformer large enough, to take this, for under $$100 Any suggestions?

Topic by bwpatton1    |  last reply


Ghetto programmer and 16Mhz

First off, Hello everyone. I built the ghetto parallel port programmer, adjusting the pinouts to work with a attiny26 and it works flawlessly.Kudos to the author.My problem is that when I drop in an external crystal rated at 16Mhz I avrdude quits because of a faulty signature; I assume this means the timings are off.At firs I thought I had misconfigured the fuses, but ,thankfully, when I dropped an 8Mhz crystal in it worked again. I know this uC can be clocked this high, so what's the problem? thanks

Topic by hacim  


want help with schaer programmer

Hi every one i just have proplem i want any body help me to solve it 1) i build a schaer programmer with 74ls07 hex buffer and i get the power from transformer power supply i integrated in same circuit i getted from it rigth voltage 13 for vpp and 5 for vdd and i found that ic prog only support schaer programer i make hardware check on programmer and get good rating at vpp and vdd and clock and data in schaer clock and data only avalible when vdd is available i tried to program 16f628a i failed may reason vpp get after vdd ? and i also tried to program 16f684a and faied also i dont realy reason when i try to read from pic i some times get garbage data is it noise on data and clock ? is so how to remove it ? can i use this programmer with winpic800 ? if so tell me how ?

Topic by m_fathy  


What be the best programmer/development board for someone new?

I was wondering if anyone could point me in the right direction. I'm looking for a programmer/development board that your only limited to your knowledge and right now I don't have much, but will want to expand upon it without buying a whole new programmer/development board. So I'm also looking for something that will be easy to get started in also with tutorial to get you up and running. I don't want to start with something and be cut off and have to go out and buy something completely new and start all over again learning. What would anyone recommend for me and had experience in? Thanks for your help.

Topic by Demonic_Crow    |  last reply


What hardware can I use to program an AVR?

I'm just getting into microcontrollers and I'm getting an atmega328 to practice with, and probably make an arduino out of. I'm a bit confused about what I need to turn the usb from computer into something it will understand. I was confused about if I need an ftdi cable, but I think they are only used if you are using a bootloader? So I think I need a usb to ttl converter and I've found a couple cheap ones on ebay and am wondering if they will work. http://www.ebay.com/itm/NEW-USB-TTL-Converter-Module-buildin-in-CP2102-/180824855916?pt=LH_DefaultDomain_0&hash;=item2a1a00556c#ht_2026wt_958 This one I'm pretty sure will work but I think I would need to convert it to six pins for the atmega: http://www.ebay.com/itm/USBASP-USBISP-AVR-Programmer-ATMEL-ATMEGA8-ATMEGA128-ATMEGA168-New-/170787590104?pt=LH_DefaultDomain_0&hash;=item27c3bbcfd8#ht_2946wt_958 Sorry for such a beginner question I'm just getting started!

Question by sk8aseth    |  last reply


how usb programmer works?

I'm using usb programmer for AVR microcontrollers.How it works,which program is there in microcontroller on it?

Question  


Atmel 89 series programmer, (http://chaokhun.kmitl.ac.th/~kswichit/89prog/index.html)

Has anyone made it work? can u help me? and also can it be connected via usb? coz i'm really having a hard time making it.

Question by No-Shi-De    |  last reply


Test a PIC16F819-I/P to see if it works? Answered

Hey everybody. I am normally an Arduino user but I have a nice pile of PIC16F819-I/P chips and would like to test them to see if they work. I don't want to get the ChipKit programmer quite yet and would like to upload a "blink" program to the PICs from an Arduino. Does anybody have a good 'ible that would work with this particular chip?

Question by ThothLoki    |  last reply


I'm Curious about micro controllers but I dont understand cause Im a newbie to begin using them Answered

Okay, I see you can use an arduino to program microcontrollers. But I dont understand how you make your project stand alone afterwards... Do you go buy another programmer? I get TOO Much info on the net to put this in perspective... could someone please help? by the way are microcontrollers and an arduino the same thing... is there something better... less expensive... what does Texas instruments have for less than 5$?

Question by BluTiger    |  last reply


Mobile Device Programmers Contest !

Prize/Contest InformationTen winners based on popular vote by registered voters will be selected, who will all receive a Mobile Internet Device as well as USD $1,000 (total value USD $1,500.00). The top 10 winners will only be eligible to receive prizes if they agree to compete for the grand prize and submit working beta applications for MID devices.Grand Prize winners will receive 2 round-trip airline tickets to anywhere in the world to an Open Source event, including 1 week of accommodations. Grand prize valued at up to USD $6,000. Intel and Moblin will pick the airline and hotels for the grand Prize winners.Terms and ConditionThe contest is open to individuals and companies eligible to work and live in USA. Individuals must be 18 or older to enter. Employees of Intel Corporation, its affiliates, subsidiaries, advertising and promotion agencies, and the immediate families of each may not enter. Companies with an existing technology enabling account with Intel Corporation are not eligible to enter. Past winners in any category will not be eligible for re-entry with the same game that previously won. Void where prohibited.You must have legal right to commercially distribute your entry in order to be eligible...Here is the SOURCE link...

Topic by Goodhart    |  last reply


Arduino as an ISP Programmer???? No luck so far :(

Hi, I've owned an Arduino Duemilanove for a while, and I love its functionality and all that it can do. I also like to program chips(PIC, and AVR) as it is pretty much an Arduino in super miniature form. But theres one problem, I dont own a working PIC or AVR Programmer! I looked around online and the only low-priced ones I could find(<$20USD) were Serial(I only have 1 serial port, but It's being used by my monitor, which I kind of need to see what I'm programming...). I have plenty of USB ports, but the USB programmers are over my budget. I would love to make one(I'm more of a DIY person) but I've heard from a few sources that the FT232RL and MAX232(UART<->RS232 converters)  wont work for the application of programming(but theres one on the Arduino?!?!?), so I'm out of luck there. But then I put 2 and 2 together: Why not just use my Arduino as an AVR programmer? So I went online hoping to find a shield I could buy for cheap, or at least a schematic. And I got nothing. The only thing I found close is how to program an Arduino with another Arduino, but I only want to use an Attiny13, or Attiny2313; Not the big Atmegaxxx. So now my question I present to you: How can I program an Attiny13/2313 with an Arduino, preferably(but not requiredly, anything really) with the ArduinoISP sketch included with the arduino IDE?

Topic by metrogdor22    |  last reply


Looking to hire LED programmer, where can I find them?

Hello fellow Instructable members! I'm working on a project and need to hire someone who is knows about LEDs and programming them to do things very similar to Daft Punks helmets. I am preferably looking for somebody within the New York area. Also if you have work that you have done already please send me links or examples of your work this will help greatly. If you are interested in this job please reply to this post or even if you have places I can call or any suggestions of where I can find such a person any information will be incredibly appreciated. I am ideally looking to complete this project by mid-January. Thanks so much! Coco

Topic by Cocasm    |  last reply


Where do I find LED programmers? Think Daft Punk helmetish

Hello fellow Instructable members! I'm working on a project and need to hire someone who is knows about LEDs and programming them to do things very similar to Daft Punks helmets. I am preferably looking for somebody within the New York area. Also if you have work that you have done already please send me links or examples of your work this will help greatly. If you are interested in this job please reply to this post or even if you have places I can call or any suggestions of where I can find such a person any information will be incredibly appreciated. I am ideally looking to complete this project by mid-January. Thanks so much! Coco

Topic by Cocasm    |  last reply


Arduino Nano as ISP Programmer?

I was excited to find out that an arduino could be used as an ISP programmer. But when I found out that the arduino uno does not support this feature, my dreams were crushed. I did recently buy an arduino nano and was wondering if I could use this as an ISP programmer. Any thoughts? Thanks for the help!

Topic by Robot Lover  


Computer Programmer Needed For Interview

I am doing a project in school where I have to interview a computer programmer. The idea is to for me to learn how a practitioner in the field of computer programming works. Expect to be asked questions about computer languages, and a description of your job among other things. I will be posting this message across the forums in the Science ,Tech, Wanted, Jobs & Internships, Authors, and Services sections. No payment will be given to the interviewee. To contact me please post the official tittle of your job and proof such as a picture of your workplace in the comments. If you have a degree related to computer programming please include what it is in your comment. I prefer to converse in a Skype interview or by email. Thank You!

Topic by 1440955    |  last reply


Computer Programmer Needed For Interview

I am doing a project in school where I have to interview a computer programmer. The idea is to for me to learn how a practitioner in the field of computer programming works. Expect to be asked questions about computer languages, and a description of your job among other things. I will be posting this message across the forums in the Science ,Tech, Wanted, Jobs & Internships, Authors, and Services sections. No payment will be given to the interviewee. To contact me please post the official tittle of your job and proof such as a picture of your workplace in the comments. If you have a degree related to computer programming please include what it is in your comment. I prefer to converse in a Skype interview or by email. Thank You!

Topic by 1440955  


PIC Programmer Com Port?

Hello, yesterday, I bought a PIC16F877A Microcontroller and This programmer. I also installed PicPro USB. I am using the serial to usb cable that came with it. The programmer has a location of  Port_#0001.Hub_#0009 in device manager. Now when I open PicPro USB and set it to  port 1, It gives me an error saying: There appears to be a problem accessing the COM port. I cant seem to find whats wrong. [Edit] I think that It is connected to port 24 (hence its name: Prolific USB-to-Serial Comm Port (COM24) ) and the problem with PicPro USB is that it can only have 1 digit port numbers, how do I fix that? Thanks.

Question by Seifpic    |  last reply


thème bluetooth ( programmation ) ?

Bonjour Comment créer un programme qui permette de controler des certaines fonctions a mon ordinateur AVEC LA TECHNOLOGIE BLUETOOTH Je n'ai pas besoin d'un programme ou bien logicielle mais je suis besoin de Découvrez comment la création (code java ou n'importe quelle Longages de programmation) merci d'avance

Question by otouati  


avrdude: stk500_recv(): programmer is not responding?

Hello, I have an Arduino uno with Atmega 328 pu and arduino ide 1.0.6programming language. I am using a Mac10.6.3. Whenever I try to upload a program, It tells me avrdude: stk500_recv(): programmer is not responding. I have downloaded all the drivers and normally the port that the Arduino is on starts with  /dev/tty.bluetooth, but that does not show up. I have tried on a PC also and it doesn't upload either.please help me. I

Question by nevet scarlet    |  last reply


OTP One Time Programme

Could any one point me in the direction to purchase greeting card sound module any and all info appreciated. Kevare

Topic by kevare    |  last reply


CyberK'NEX Personality Programmer software

Hi, I'm looking for the software to program the Cyber K'NEX utra sets. They are no longer available from the K'nex website. Does anyone know a place where I can download this? or does anyone still has this on his PC ? thanks in advance, K'nex fan from Belgium (Europe)

Topic by Jorian  


CyberK'NEX Personality Programmer software

Hi, I'm looking for the software to program the Cyber K'NEX utra sets. They are no longer available from the K'nex website. Does anyone know a place where I can download this? or does anyone still has this on his PC ? thanks in advance, K'nex fan from Belgium (Europe)

Topic by Jorian    |  last reply


help with (possibly) programmable chips? Answered

Hey eveyone, i want help figuring out if  can use either of these 2 chips for programming. the datasheets are below: atmel at29c512-90jc  \/ http://www.atmel.com/dyn/resources/prod_documents/doc0456.pdf or mosel vitelic v29c51002t   \/ http://www.datasheetcatalog.org/datasheet/mosel/V29C51002T.pdf' any help is appreciated

Question by zack247    |  last reply


Securing programmable IC chips Answered

I've just started playing with Arduino boards and programming and I am curious about firmware or downloading a program to a chip upon completion so the project remains so I can keep it intact after I remove the Arduino interface. Can you buy inexpensive chips and download a program to the chip with all the instructions on it so I don't have to leave the Arduino board connected to it. I've heard there are inexpensive one time chips that you can download too and that's pretty much it. Once the program is in, its in and you can't reprogram it again so my questions are this 1) can this be done? 2) does anyone have an Instructable for a project that uses this, and finally, where can I get such programmable chips? Any assistance or advise is most appreciated.

Question by happywatt    |  last reply


Core Wars: The battle of the programmers.

Okay, brace yourself for a lengthy background story: In the 1960's and 70's, computers were much too expensive for a normal person to have one all to themselves. Before the invention of the Personal Computer (PC), computer systems were mainly employed in large universities, able to be used by students. However, there came a danger with all this: Back then, there was no such thing as protected memory, meaning that someone with minor hacking skills and some knowledge of assembly could easily wreak havoc on other people's data and programs. One such urban legend is that of a major business firm's main computer system, which a mischievous employee had installed his own assembly program called creeper, who's only purpose was to create copies of itself whenever it was run. This soon became a problem, as the creeper virus began eating up precious space in the memory and began corrupting other people's data and programs. After a while, another more brightly-hatted programmer created a program called reaper, which would make numerous copies of itself and destroy any creeper virii it could find and then self-destruct. Soon enough, things were back to normal. After hearing this story, a programmer named A.K. Dewdney got the idea for a game which he called "Core Wars". In this game, people would write computer programs called "warriors" in an assembly language called Redcode. Redcode had instructions not out of the ordinary of any assembly language. These programs were then run simultaneously in a simulated computer called MARS. The aim of the game was to make the opposing program crash by forcing it to execute an illegal command in the computer's shared memory. The surviving program was declared the winner. The absolute simplest warrior was called imp, and was written by Dewdney: MOV 0, 1 The MOV command moves copies a command from one place to another, in a position relative to the MOV command. Because of this, the imp would fill up the entire memory with MOV commands in a relatively short amount of time. Because the memory loops around (So, if the size of the memory is 8000 commands, then command 8001 would be executed as command 0) then it meant imp would always hit it's target eventually if it wasn't hit first. Another program which was written by Dewdney is called Dwarf: bomb      DAT 0,0 Dwarf     ADD #4,-1                 MOV bomb,@bomb                JMP Dwarf End Dwarf This is the first example of a "bomber" program. This program would drop DAT 0,0 (An illegal command) at every fourth slot in the memory in the hopes that the other program would accidentally execute it (cookie if you can figure out how it works). There are far other types of examples, like scanners, which try to scan the commands around it to see if they are illegal. Some programs can even repair themselves mid-battle. So, does anyone else still partake in this ancient game? I recently just got into it, writing my first warrior program a few days ago. Have no idea if it works, but it sounds pretty cool. It's based off of Dewdneys Dwarf but with a few modifications (I named it MindSplitter): bomb      SPL 1                 JMP -1                 DAT 0,0 Split        ADD #5,-1                 MOV bomb,@bomb                JMP Split End Split First off, this plants bombs at every fifth command instead of fourth, which I hope will help it spread out. Second, the bomb it uses is my personal invention that I call the Splitter bomb. In Redcode, the SPL command will jump execution to the specified command, while at the same time continue executing the commands after it. The idea is that the SPL will split to the jump command while the normal execution goes to the jump command, and both of them jump back to the SPL, therefore filling up all of the enemy programs processes. If the enemy program somehow manages to escape the loop, there is a deadly DAT after it. I haven't tried this out yet and I'm not sure how it would do in battle. If someone with a MARS emulator and a warrior of their own would like to put it to the test, I'd would absolutely love to hear how it turns out :).

Topic by dungeon runner    |  last reply


Sparkfun USB Programmer For PICAXE Not Working? Answered

I have the PICAXE USB Programmer from sparkfun but it does not work it says no hardware detected on COM 4 I have installed the drivers I am using Windows XP.how can I get it to work.I have made the download circuit correctly.

Question by Bot1398    |  last reply


how do i make my ghetto programmer to work?? Answered

Im using this programmer:https://www.instructables.com/id/ghetto-programmer-improvement/and i use the program for flashing a led written by the real elliotbut it wont load...i downloaded winAVR, loaded everything, put in the attiny13 chip, connected everything right, re-wrote the program for attiny13 (changing output ports) but it gives the error> Failed to create process: the system cannot find the given file.the last part is translated since im running the program in dutch...what is going on? and what can i do about it?

Question by godofal    |  last reply


Can I use an Arduino to program an AT89S52 using ISP?

Since the AT89S52 controller is ISP programmable is it possible to use an Arduino UNO as a programmer to upload the hex file to the 8952 ? I've tried various programmer softwares such as progisp, 8051 loader and ISP Prog v1.4 but the Arduino doesn't show up as a programmer on any of these. I've uploaded the ArduinoISP sketch on the UNO and then tried to program the 8952 without any luck. According to my understanding the ISP programmers use an ATMega8 ,so is what I'm trying to do possible or do I need to purchase an ISP programmer ?

Question by r5sb    |  last reply


Do different AVR microcontrollers have different ISP pins? Answered

I am building an avr programmer shield for an Arduino. I need to know if all 8 pin/14 pin/20 pin/28 pin/40 pin avrs have the isp pins in the same spot. In other words, is every 8 pin avr going to have it's isp pins on the same 4 pins, or are there variations?

Question by Teslaling    |  last reply


I Need a Game Design Team (Mobile Game Development)

Hey guys, I am looking for a game design team to help out with a project I am starting.  It will be a mobile game similar to Clash of Clans, but with many different gameplay changes.  I have a lot of the game planned out, but I don't want to have to learn all of the different skills it would take to make the game on my own.  I have some 3D modelling skills with blender, and will also do most of the gameplay design. People I Need: -Another 3D modeler to work with and help reduce the workload -A texturer -A programmer with the skill to put a mobile game together -An animator -An artist (for main map, interface, etc) -Possibly someone for sound; I can probably do that I would assume that the game will be created in Unity, but that mainly depends on the group's preferences.  If the programmer has the skill, he could just custom code the game, and it would definitely run better that way.  Anyways, whatever money is made from this project will be split equally between everyone except for the programmer; I know how much work that would take, he will probably get a little bit larger of the share. Reply with your email and I will send you the basic outline of the game. -Josh PS: Please, only native English speaking people; I've worked with non-natives, and I have found communication to be very tedious...

Topic by JoshuaT3    |  last reply


Where can I get a cheap AVR programmer

Hi, I'm working on a project and am wondering: Where can I get a cheap AVR programmer compatible with Atmega chips? Specifically the ATmega32U4. It does not need to have a socket for the chip, I'll be doing in circuit programming. Please help.

Topic by gimmelotsarobots    |  last reply


Did the today views "resetter" fall asleep at the key board thingee?

Self explanatory, I believe...maybe some body knows the answer?  Maybe there is another place to put this question...I don't know...

Question by Creativeman    |  last reply


PicProgrammer

Does anybody know of a schematic to program an 8 pin picmicro controller such as: 12F675 12F508 Just those specifically because they're 8 pin and I have them. Correct me if I'm wrong, but one of those 2 has 8 I/O ports, which leads to a lot of possiblities for a small area. Also this will be my first real pic project.

Topic by guyfrom7up    |  last reply


AAAAAAaaaaaaaaaahh!!!!! WHY WHY WHY Cant my computer see my Arduino? Answered

Going on my 2nd week...thats 14 days  of trying EVERYTHING I can find to get my Win xp pro 32bit - sp3 to see anything beyond the USBasp?   I've completely given up on trying to get the UNO direct USB hookup...I only get NEW DEVICE- USB2.0-SERIAL . Uninstalled-reinstalled- repeat with port changes and following the SAME directions posted all over the interwebs.  My DIYduinos have UNO and 2 with Deum'nove bootloaded and blink sketch installed when I purchased them....they give the blinkin LED when powered up. I've also had several unsuccessful attempts at the FTDI driver....the USB2.0 "official" drivers...the Arduino IDE USB driver..you name it...I probably tried it.  nothin' I'm no baby, but, I'm seriously on the verge of frustration tears!!  apparently I'm the only one who has this issue 'cause theres nothing I can find on it...the existing instructions out there are sooo frustrating in themselves as they just plug it in and there computer sees the UNO or whatever and they just go on from there...or stop after windows sees the USBasp programmer....I have THAT but, cant get any further with it. My Uno clone has a10 pin USBasp header on it...says right on it USBasp!...When I hook it all up, I get power on the board(s) from the USBasp programmer hooked to my comp...windows sees the USBasp but nothing attached...let alone a virtual com port arrangment. PLEASE anyone who knows what the issue might be or an educated guess is welcome too!!!  I'll send you Art!  or a 'duino with LM293D chips able to drive 2 stepper motors I've made!  if you solve it...you'll be rewarded somehow!!!

Question by schel    |  last reply


how can i creating a programmable borad?

Can any one help me to creating a programmable board with c++ or any other language thnx for all

Question by iraqi    |  last reply


how i can make i Programmer to program the Atmega16?

I need programmer but in my Zone i don't have any store or supermarket to sell a programmer 'Atmega16' but i have some store sell Electronic parts. i need way to Invention  a programmer                                                                                     Thanks....

Question by matrex    |  last reply


Are there any common timers that are programmable to the second? (my sprinkler timer is programmable only to the minute)

We are using a sprinkler timer to automate the opening and closing of a ball valve by linear actuator. The problem is the sprinkler timer is only programmable to the minute, so it opens, lets water flow for a minute, and then closes. This wastes water as we only need to empy the tank for 10-ish seconds. Any timers that are programmable to the second?

Question by paulpaulpaulpaul    |  last reply


How to construct a programmer for Atmel AT89S52 microcontroller? Answered

I have been trying to construct a ISP Programmer for AT89S52 microcontroller and my previous attempts were not fruitful... So please help me..

Question by batta420    |  last reply


Poll:Do you use an EPROM PROGRAMMER?

1.Do you have an eprom programmer? 2.Have you recently used or thought about using an Eprom in a project? 3.If you don't have an eprom programmer, would you be interested in Making or having one? 4.Do you think eproms are obsolete? 5.Can you think of a use for an eprom? 6.Are eproms too unusual to use in a Make or Instructable project?

Topic by VIRON    |  last reply


is the ps2 connected mouse's microcontroller programmable ? Answered

I heard that the ps-2 connected mouse has a microcontroller , is that true? and if it's true is it programmable?

Question by top.boy    |  last reply


Where are PIC16F628(A) programmers &amp; prices available ? Answered

I have been having a real hard time finding them....and I don't normally have a rough time with Google :-) I am FRUSTRATED and you thought I was actually GoodHart LOL I found a lot of advice out there (simple to use and efficient JDM type programmer......no, JDM's rarely work, use MCU.....try this Starter kit....don't use that starter kit, it is inaccurate.....etc. & etc.).

Question by Goodhart    |  last reply