Rotary magazine

So I've been trying to build again. I had an entirely different project in mind but I noticed that the teeth of gears fit into the grooves of rods. I was experimenting with it quick to see if a gear would make a decent pin lock (it doesn't). I kept toying with it until I went off on this entirely random tangent without planning on it, hence the mismatched colors for the one slot connectors.  Anyway, this is a rotary magazine. Similar to a drum magazine, it's just a magazine in cylindrical form factor rather than a linear form factor. I'm not sure if anyone was able to successfully make one before. This version in particular stores 12 usable blue rods and one extra one that can't be fired. It has a ball joint connector to act as a paddle to help ensure the rods continue feeding without skipping teeth. I don't have many dark grey connectors but otherwise I'd scale this up using red rods and then store yellow rods. It'd be more useful as it'd fit more nicely with a connector body. Currently to maximize ammo use, I'm trying to fire directly from the magazine without feeding it further vertically. The problem is it's obviously an awkward fit. If you imagine a typical 5 layer gun, it'd fit in between layers 1-2 and 4-5 about halfway each. It's entirely doable, but just doesn't look too pretty.   It's nice in that it allows you to store a fair amount of ammo in a relatively compact amount of space, but it's otherwise not a practical storage solution as is. Aside from just trying to figure out how to attach it to a gun, figuring out how to reload it conveniently would be difficult. It -might- be more useful if it can be turned into a roofed, removable magazine. Then at least you can preload them first.  I hope someone can give a weapon that uses this a shot. Perhaps a bolt action for better performance. And again, I'd scale it up to store yellow rods so it's a little easier to use in a standard connector body.  Here's a quick video demonstration and a look inside it at the end:

Topic by TheDunkis   |  last reply


DIY rotary processor

Any body know what sort of motor you would use to make something like this?

Topic by sharktopus   |  last reply


Rotary input for a cellphone

I have an idea to do a total conversion on a cellphone, including things like a steam-driven charger, etc. The issue I am running into here is if I could, I'd want to make it rotary. I saw Randofo's PIC method for making it a USB input here but I have no clue in terms of how a cellphone works, or any of the chips involved. Sadly, my knowledge is mechanical, not circuitry. Any sort of ideas are welcome... please help me progress on what I hope to be my magnum opus of steampunkerie.

Topic by Harlequin   |  last reply


Rotary dial phone

Hi all, Yesterday, my grandma gave me an old telephone. My mother used it as a toy, so my grandfather disconnected the wires (for safety). I wanted to connect the phone, but I don't know which connections I need. I attached some photo's to make the situation clear. It would be great if you could help me! Arnout P.S.: English is not my mother tongue so it would be fantastic if you didn't use a vocabulary that's too difficult ;)

Topic by arnoutdejans   |  last reply


Which rotary tool?

I recently got some money from the government for my good grades (YAY!) So now I can get myself a nice rotary tool. BUT I can't seem to make a decision! I have 2 brands in my sights Dremel (No specific model/kit in mind yet) Gyros (http://www.amazon.com/gp/product/B006ZEJA56/ref=ox_sc_act_title_1?ie=UTF8&m;=AXL381AZQM9Q1) And if it isn't a POS Northern Industrial (http://www.amazon.com/gp/product/B000JFO1TM/ref=ox_sc_act_title_2?ie=UTF8&m;=AF8EGQ3KRZQB6) I am leaning more towards Gyros as their attachments seem pretty good. Its also significantly cheaper than Dremel. Please give honest feedback. Thanks!

Topic by micraman   |  last reply


Infinite Rotary Switch? Answered

I'm looking for the search term I need to find a "Rotary Switch" That spins very smooth and will keep spinning indefinitely like a volume control switch.

Question by bradleynelson102   |  last reply


Dremel Rotary Tool? Answered

Where can I buy attachments for a Dremel 200 Rotary Tool. I know it is an older model and I've already tried search engines. Anyone know anywhere online or in a store where I can buy drill,saw,and grinding attachments (specifically larger ones)? All help is appreciated. -E

Question by DELETED_explosionist   |  last reply


rybobi or ozito rotary tool

Hi everyone, i saw the ozito rotary tool for $39 and the ryobi for $97 at bunnings, will the dremel bits fit these two items and will the router attachment (the round one that comes with the dremel )fit them does anyone have any advice on which one and why and pics or info would be great

Topic by Gainey   |  last reply


Correct Wiring of a Rotary Switch Answered

Hi all, I was wondering if anyone could advise on the correct way to wire up a pair of 4 way rotary switches. Similar to these https://www.amazon.co.uk/SZW26-20-D505-5-Universal-Change-Combination/dp/B00A8ZEXDC There is no common live it just makes an connection between terminals 1&2 in pos 1, then 3&4 in pos 2 etc Its to switch between 4 fixed speeds on a pair of 1ph centrifugal fans in my workshop, they will be placed in an enclosure and require 4 live connections each, do I just run a the main live into terminal 1 and bridge that into the other 3 or should the wire be split prior to connection, as in 4 individual wires? On UK mains 230v, low amps, 4 max

Question by Squibo   |  last reply


Looking for a rotary switch to fix my fan

Greetings.  I'm looking for a 3-way rotary switch to replace the broken one in my Patton fan.  Here are pictures of the original. http://www.flickr.com/photos/50514348@N06/sets/72157624310895288/ The company that made the switch does not sell parts retail so I can't do that.  It seems to be a very simple switch.  It's 4 click.  Off, High, Medium, Low. I'd hate to throw this fan out.  The actual motor is in perfect shape.

Topic by doublejnyc   |  last reply


Wen 2307 Rotary Tool - Help needed

Hi there everyone, I need a bit of help if available. I purchased a WEN 2307 101-piece rotary tool set from Amazon.ca a few weeks ago and followed that purchase with a Flexible Drive shaft.  Although I was able to attach the drive shaft to the tool, the bits that came with the WEN don't seem to fit the collet of the drive shaft properly.  Therefore, I am planning on returning the drive shaft and purchasing a different unit from a different supplier on Amazon. The unit that I am considering is an SPTA Electric Grinder Flexible Flex Shaft Rotary Tool Attachment 42" Length and Rotary Accessory which states that it fits All 1/8" rotary tools. Of course, the drive shaft didn't come with a manual, so I figured out myself how it is supposed to attach. I'm not very familiar with rotary tools and purchased this unit as a beginner, instead of spending a lot of money on a really good Dremel. That being said, I would like to know if the size of the collet is equal to the same size bit.  (i.e., if the rotary tool is fitted with a 1/8" collet, do you use 1/8" bits, or do you use a different size? I know that this seems like such a stupid and/or easy question to most people, but, being a beginner, this can be quite confusing. Any assistance that you can offer will be greatly appreciated. Thanks

Topic by freddyguy1   |  last reply


Can a rotary phone be hooked up to wireless phone jack system and work? Answered

I have an old retro looking rotary phone I want to hook up as simply as possible because I don't want to run a phone wire if I don't have to because the area is not that easily accessed.

Question by BTGuy   |  last reply


how to rewire a rotary phone to be able to hook in to a modern phone jack?

 I have a what I believe you call a cradle style rotary phone of unknown year or make, model is "the cutie"and was made in Japan.Would like to modify it to hook into home phone jack. Either by replacing the existing phone cord or adding jack to existing cord. Cord has 3 wires one green, one yellow + one red. Green and yellow are connected on to same post @ cord end ( post used to hook into wall) red into the other post.Anything else needed to get this phone  ringing let me know.

Question by 4kelso   |  last reply


difference between these rotary shears? Answered

Hello, I want to buy some rotary shears. I can find two different designs. Is there any difference in the performance of these two types ( I know that one has a guide bar for cutting straight edges )  ? Thanks

Question by FriendOfHumanity   |  last reply


B&D Rotary Tool

I've really wanted a dremel lately...but they're so darn expensive! I saw this Black and Decker one that looks pretty good for a decent price. (Plus, I have a $25 gift certificate) What do you all think? Target's amazon page is selling one for 29.99 + 4.99 shippinghttp://www.amazon.com/Black-Decker-RTX-6-3-Speed-Accessories/dp/B0001GUDRI/ref=pd_ts_hi_10/002-0324667-5924070?ie=UTF8&s;=hi

Topic by Weissensteinburg   |  last reply


dremel guide (for admins or moderators)

I think that you guys (instructables) should make a guide on dremel care, hacks, fixes, and projects (emphasis on projects) i just bought a dremel and i love it but i want something to do with it. please consider this -kieran eglin (qballcat)

Topic by qballcat   |  last reply


Old Rotary Dial Phone

Hello. I wanted to ask if someone could help me to connect an old rotary phone to the pc. I would like to make it hit the ring, and if it were possible to hear any sound recording. I have no knowledge about such things, it is possible to do so? This is a translation of google thank you very much

Topic by erdosain9   |  last reply


Drill that is like a rotary tool.

I love my rotary tool, but sometimes it is just to fast. SOme plastics just melt, spewing hot plastic all over the place and some woods burn. A drill would work better, but the body does not handle as well as the rotary tool, plus I can't attach basic tools. So is there a drill that comes in a rotary tool body?

Topic by BoomGuy   |  last reply


How to wire rotary switches?

I have two rotary switches with 6 (six) positions each. To control ( 8 different model railroad tracks)...(12 volts on each track) The switches (from radio shack) have all seperate positions with (I assume) the power supply from the two terminals in the middle of the switch. Is there a way to identify the polarity of the leads or am I even connecting them properly??? HELLLPPP!!!!

Question by othimus   |  last reply


Cheap rotary tools/dremels

What do you guys think about these? Are they any good? Im talking about the really cheap £5-£10 ($10-$20) ones. I've always wanted a dremel but I didn't want to fork out more than about £10. Thanks - Josh.

Topic by josh92176   |  last reply


Rotary (pot) to mouse emulation

I am trying to create an autocue controler. (I've built all the software in Javascript to run in browser windows) When you press a button in Firefox / Explorer, a circle with 2 arrows appears allowing you to scroll up and down. If you move the mouse, the speed of the scroll changes. I want  - if not too complex - emulate this behaviour externally. My idea is to have a rotary control replace the mouse mvement such that you turn it one way the screen scrolls up, and ditto in reverse. And the further you turn the wheel one way or the other, the faster / slower the scroll goes. I did think about using a PS2 mouse thinking it would be a simple case of replacing the sensor, and sending pulses to the chip to emulate the encoder output. But now I understand the LED in these sensors is pulsed, and that the encoder also generates a quadrature signal to the IC chip. Apart from which, those mouse / IC chips are now obsolete!! Anyone any ideas? ** In the days of serial on the old PC's like ZX80, you simply sent a pulse to emulate a mouse click: rapid fire was simply a matter of increasing mark/space timings

Topic by diy-video-gadgets 


ROTARY SAW MOTOR, WHAT TO DO?

I have an old rotary saw where the motor works but the rest is broken what can i do with the motor i need creative ideas and remember there are no wrong awnsers

Question by bossmansam   |  last reply


Mouse wheel. How do I replace optical encoder with rotary encoder?

Hi, I have a Belkin Nostromo N52 controller. It has a mousewheel that can be custom programmed independently from the wheel in your regular mouse. I want to use it as a jog dial so I want to remove it from the original place and replace the rubber wheel with a jog dial. Basically it is to rotate the wheel 90 degrees as they did here with a mouse: https://www.instructables.com/id/Desktop-Scroll-Wheel-and-Volume-Control/?ALLSTEPS The problem is the Nostromo wheel uses an optical encoder instead of a rotary encoder (the typical used by half of the mouse wheels in the world). The mod I want to do would be a little complicated using the optical encoder (I would have to use a piece of PCB perpendiculary soldered to the main PCB and the height of the resulting device would be very tall for what I want) but it would be very easy if I could replace the optical encoder with a rotary encoder I salvaged from a mouse since it can be laid down on the PCB pretty well. The problem is the signals of the optical encoder and the signals of the rotary encoder are different. The middle leg of the receiver in the optical encoder is connected to +5vcc while the outputs are connected to ground using 10KΩ resistors. In the rotary encoder, the first leg is connected to ground and the other two go directly to the mouse IC. I tried to remove the optical encoder of the Nostromo and connect the two outputs of the rotary encoder to where the outputs of the IR detector go and the third leg to ground but all I get is a permanently actived scroll down (as if the wheel was scrolling down all the time). I didn't dare to connect the third leg to Vcc just in case I blow the thing. I think there must be a way to replace the optical encoder with a rotary encoder and get the same signals and I think this involves using the Vcc line and resistors but since I'm not very good at the electronic side of things, I don't know how to do it. I'm enclosing a diagram of the optical encoder circuit. The diagram on the right enclosed in question marks is what I guess would be the equivalent circuit for the rotary encoder but I'm not sure. Can anybody confirm it or point out the appropriate corrections? Thank you.

Topic by jedikalimero   |  last reply


wiring a dpdt switch like a dpst switch

I need a DPST rotary switch so that i can turn on two circuits at once but the closest i've been able to find with appropriate ratings is a DPDT switch, is it possible to wire it up to my circuits in such a way that it works like a DPST switch? I've attached an example diagram i found of a DPDT switch, if i was to disconnect the lamp from pin 1 and the buzzer from pin 2 would the first position of the switch become Off and the second position become On powering the LED and speaker? also assuming that the LED and speaker only connected back to their respective batteries and not to each other, could i attach a low voltage battery to pin 3 for the LED and a higher voltage battery to pin 4 for the speaker without causing damage?

Topic by ambientvoid   |  last reply


How can I modify this circuit to sequentially turn on LEDs in parallel, while avoiding voltage drops? Answered

I have a single pole, 12 throw rotary switch which I want to solder to a set of LEDs so that rotating the switch clockwise lights more LEDs as follows: 1 = 1 Red LED 2 = 2 Red LEDs 3 = 3 Red LEDs 4 = 4 Red LEDs 5 = 5 Yellow LEDs 6 = 6 Yellow LEDs 7 = 7 Yellow LEDs 8 = 8 Yellow LEDs 9 = 9 Blue LEDs 10 = 10 Blue LEDs 11 = 11 Blue LEDs 12 = 12 Blue LEDs Since there will be a voltage drop across the diodes, the LEDs at the start of the chain will get progressively dimmer, and increasing the voltage would blow the LEDs in shorter chains. One modification I know I could already make would be to not use the first 4 diodes on the yellow LEDs, and the first 8 diodes on the red LEDs, as a minimum of 5 yellows and 9 blue will be active for each position. This still leaves a maximum of 3 diodes in each chain, which I still think would cause the lights to be much dimmer. Another solution I can think of is to have multiple wires coming from each terminal of the switch, each with their own diode, which would ensure all active LEDs had the same brightness (I'm not sure if this would cause the whole chain to be dimmer than shorter chains or not). The downside is this would need  31 wires rather than 13, and that's only if I bridged together all the shortest LED chains of each sequence: individual wires for absolutely every position would mean 79 wires+diodes). To put this in context, I want to create the health bar from Dead Space 3: If you can suggest a way of improving the circuit, or totally re-designing it, it'd help me loads! Thanks!

Question by Shadow Of Intent   |  last reply


Rotary dialer in modern cell phone

I want to merge rotary dialer with a modern cell phone. Can anyone help me with this, please? Actually I have to convert rotary dialer's analog signals to cell phone's way of dialing -- key closing...

Topic by Blinchik   |  last reply


Rotary Tool neck thread size

I have several ideas for rotary tool accessories that would make my life easier, but they would have to be attached at the neck. So I need to cut out a hole, and tap it out to the right thread size. Anyone know what that is?

Topic by BoomGuy   |  last reply


How to attach a shaft to a rotary encoder? Answered

What are the options to attach a shaft to a rotary encoder such as this : https://www.adafruit.com/products/377 My idea is to fix a cable to around a shaft, so as to have the shaft turn when the cable is pulled, but then I want to measure the rotation. That's why I'd like to attach the end of the encoder to the end of the shaft.  Any ideas on this? I have to build the whole contraption from scratch. Thanks Mariano

Question by marianov   |  last reply


Model 500 Rotary Phone help

I am custom painting one of my Model 500 Western Electric Rotary Phones for my brother's birthday.I am considering modifying the ringer, or even adding an alternate ringer via a switch, that will play an electronic ring of my choice. Specifically I want it to play the fight song of his College.This site has a schematic of the model 500. I am a little vexed as to whether or not I can pull this off, can anyone add some help?http://www.porticus.org/bell/telephones-500.html

Topic by Legionnary   |  last reply


ANOTHER Rotary barrel gun project!

Here's the deal: 1865 Gatling gun Crank powered (working on it... dont worry...) 8 barrels (rotating) WONT have a 100 round mag with working feeder (By someone who's name  I cant remember...) EDIT: Box mag didn't work out... Sorry guys! Stick mags it is! Stand (NOT the whole rolling on wheels thing!!) I want to know: Anything I've missed? Good/bad idea? General opinion on a knex version? EDIT: PICTURE IS THE SO FAR! Barrels and the crank auto mech! *Great, my lens needs a clean...*

Topic by RMConstruction   |  last reply


Rotary switch w/ direction based contacts??

I'm looking for a specific type of switch... I believe that it must exist, but I have never seen it... I need a rotary switch, where each clockwise "click" (partial turn) makes one circuit momentarily, and each counter-clockwise turn makes a different momentary conection... example with two light bulbs ( L1 and L2 ) connected to each direction of travel, respectively: If you rotate the knob one "click" (say 15 degrees) clockwise, L1 flashes for a moment, as the knob is in motion. if you continue clockwise, L1 will flash at each "click". If you rotate the knob one "click" counter-clockwise, L2 flashes for a moment. if you continue counter-clockwise, L2 will flash at each "click". There is no center-point, so any clockwise travel corresponds to L1, and any counter-clockwise travel corresponds to L2. does anyone know where I could get a couple of these??

Topic by gschoppe   |  last reply


Seeking advice on how to make a rotary dial phone have a busy signal when answered

Hi all, I'm working on a Just For Laughs-type hidden camera prank show and I need to build a prop rotary dial phone that, when answered, has a busy signal. I would prefer, if possible, to hide any additional parts inside the body of the phone. Also, just a note, the phone doesn't have to ring. If you have any advice I would love to hear!!! Many thanks, DAZU

Question by damianzuch   |  last reply


What's the name of this type of switch? Answered

What's the name of the type of switch then works by rotating it, and you can keep rotating it on one direction.  Like the kind of switch that controls the volume in a car.  I'm assuming that every click switches between being it conducting and not conducting?  I need to use one with a micro controller (I don't want to use a potentiometer because they can only rotate so much) and I need to know the name so i can buy one.

Question by guyfrom7up   |  last reply



Can you put a 13b Wankel Rotary in a Corolla or Camry? Answered

13b wankel rotary engine. 89 Corolla 87 Camry.

Question by Yerboogieman   |  last reply


Led color control w rotary switch?

I am working on a project to rewire an old industry hair dryer into a funky floor lamp. It has a cool panel on the back that would fit some kind of a rotary switch.  I would like to use an existing product or products to emit blue light and yellow light from the bell of the dryer. The rotary switch would allow me to ramp it from the blue leds to the yellow leds with some cross over in the middle. my challenge is that, while I understand basic electrical circuits, I know very little when it gets into the more technical circuits and arduino stuff. I want to learn but this isn't the project for it. does anyone know of an easy way to set this up?  My  thought was a set of blue strips, a set of yellow strips and a rotary controller. But, I don't know what to search for online. thanks!

Question by mckeephoto   |  last reply


is it possible to connect a rotary encoder to a USB A input?

Hello everyone, i've been using a laptop for a long time now and my laptop uses a touchpad scrollwheel. as we all probably know: they s*ck. lately i found instruction on how to make a desktop scrollwheel (https://www.instructables.com/id/Desktop_Scroll_Wheel_and_Volume_Control/), but is was very unclear and very large. ik started thinking of making one myself. smaller than the one they build. i would make it out of a tictac barrel and an old rotary encoder from an even older mouse. i want to use USB A input becouse that's easy to use and it's on (almost) every computer. is there any way to connect the A,B,C pins of the rotary encoder to the pins of a USB A input? p.s. i know, my english s*cks

Question by tommiesmee   |  last reply


Which optical sensor will be best for rotary encoders?

I am trying to make an Optical Rotary Encoder please can anyone suggest that which optical sensor will be best for good resolution and accuracy...I have made one using Photo diode as receptor but the proble i am facing is that switching is not fast enough which results in a lot of error....so what can be done to make photo diode switch fast or should I use some other sensor(phototransistor or Photoresistor) and please do tell the reason...thank you..

Question by malhotra18   |  last reply


Beginner Arduino Basic LCD + rotary encoders

New to Arduino, attempting to get basic programs working. Whats the best way to include multiple sensor readings to appear on a LCD Arduino screen for user feedback. So the sensor readout on the LCD would switch to the most recent change of rotation. Code to examine or help in the right direction would be appreciated. Thanks

Topic by Prime01   |  last reply


Help with Panasonic 28.8v rotary hammer drill?

One day i was working on a house where i was fixing wood fibre board to the exterior of the house. i was drilling quit alot , 20-30 minutes periods over a 8 hour day. well after a few days, my Panasonic hammer drill started smelling quite unusual. like electrical burning smell. the hammer drill lost power and altough it still worked and the end was still spinning, it was pritty much unusable. i was seeing if anyone could give me any help as to what is wrong with it as im in dire need of it at the moment and i paid too much money for it just to throw it away. any help would be great. thanks

Question by AshK10   |  last reply


I recently received my rotary encoder led ring from sparkfun, but I'm having trouble programming it.

I'm using an Arduino Uno. I found example code but it involves using a rotary encoder for input, which I don't have and don't intend on buying. Does anyone know how to program it to simply turn all the led's?

Question by midknight5000   |  last reply


Drill with wheel head instead of (dremel) rotary tool?

(new member) quick question: Instead of buying a dremel rotary tool, couldn't I just buy a drill head that mimics the wheel-cutter attachment.... that you would normally use on a dremel?

Question by trustsushi   |  last reply


Q: cheapest way to remove bottom of water-heater

Hi, i pulled an electric water-heater (about 80 l) out of the trash. want to take the bottom off and convert it in a pot/kettle to do (´cook´ ) laundry over a wood-fire.i was wondering what would be the cheapest way to do it (i have very few means here)... rotary-tool?, hacksaw-blade?... (dont have a grinder, no blow-torch, no jig)guess to complete the cut i would use up quite a few of wheels, or, respectively blades (hack).any ideas? any feedback... all appreciated.bowing.

Question by la xerra   |  last reply


How to use a rotary encoder as momentary/push buttons? Answered

Hi all, there is an instructable where the guy is using a rotary encoder instead of the push buttons. I tried to get in touch with the him for the connection diagram, but no answer... :( It doesn't look like he is using and micro controller, but most likely he is, under that small piece of perfboard... Can you guys help me and others out with some knowledge? Thank you!

Question by GellertK   |  last reply


Thinking of turning a crappy rotary tool into a useful device, any ideas?

So I just bought a nice Dremel, meaning my crappy 15 dollar Harbor Freight rotary is worthless. Since I won't be using it for rotary projects anymore, any advice on what I can use it for? I'm thinking something along the lines of the drill to lathe conversions I've seen, but I doubt it has enough power for something like that..?

Question by rozmusway   |  last reply



Rotary Phone made wireless without any rewire?

What cool thing would be if a Old Rotary Phone could be conected with your 2 wires into a Battery powered "thing" that would make this old phone wireless and fully working to the new line system? There´s plenty of instructables out there where you can rewire your phone to make it work nowadays... But if you could use your old rotary phone without making changes, just connecting the jack and the board make all the magic? By this way you not only would have a original phone but would also make it usable for our new technology.

Question by VanessaC106   |  last reply


Ever seen a rotary tool that used a large flywheel?

Has anyone ever seen or built any kind of rotary tool that was driven by the inertia of a large, heavy flywheel? I have seen kick wheels for pottery, but i am curious about a vertical flywheel. Lathe, Grinder, pump.... Seems like you could attach a treadle to a pedal assebly of an old bicycle to drive the flywheel....if the pedal assembly was the free wheeling kind, and there was something pulling the treadle back up, it would only power the flywheel when the treadle was pushed down.

Question by ClandestineIntestine   |  last reply


What's another name for a rotary pneumatic indexing valve?

I am trying to find or create an air indexing or selection valve that has one line going in and several (6 to 12) coming out. I can imagine how to create such a thing: A valve disk that rotates in a body with 6 to 12 outlet fittings on the valve housing. The disk has one hole cut radially and one cut axially intersecting it at the center. Install in the valve body, spin it around with the valve stem, and there you go. Agitate away!The thing is, I'll bet these already exist if I could find them. Can anyone tell me what this thing-a-ma-bob is called? Or who might make them?

Question by cmblocker95   |  last reply


which of these are better? Answered

Http://www.harborfreight.com/cpi/ctaf/Displayitem.taf?itemnumber=94076 http://www.harborfreight.com/cpi/ctaf/Displayitem.taf? itemnumber=92880http://www.harborfreight.com/cpi/ctaf/displayitem.taf?Itemnumber=40457  

Question by NatureBoom21   |  last reply