Whisker Wire

Where can I buy some whisker wire? I am building an OAWR and I cannot find whisker wire anywhere! please help!!!

Topic by crohnsninja   |  last reply


Magnet Wire

Cutting open transformers (you might call it an adapter, or charger) yields a good quantity of re-usable magnet wire. Motors don't seem to be a very good source, since the windings on those seem to be saturated in varnish to glue em together. Apparently, vibration is more of an issue in the motors, so they make the windings solid. This might be different in little hobby motors. Dunno.

Topic by Toga_Dan 


nichrome wire

I got some nichrome wire off eBay, and it works great but when I connected it to a 9 volt battery it barley got hot, then I attached it to 4 x AA batteries and it got red hot. why is this? I don't understand because the 9 volt gives out 9 volts(duh) , but the 4x AA batteries only gives out 6 volts.

Topic by Jordo   |  last reply


Help with wiring

I have disassembled an old vacuum cleaner that runs on 240v/5amps/1200w. I wanted to obtain the electric motor that should perform at 1.5 horsepower. As I was taking it apart I forgot how the switch leads were originally configured. I want to give the motor a test run but I don't want to hit the fuse in my house so I was hoping someone can help me plug the switch in the normal configuration. What order do the brown and blue plugs (that comes from wall plug) fit into the switch? And what order do the blue plugs (goes to motor) fit into the switch? A silly question really but I am new to working with electronics.

Topic by Tyoon   |  last reply


Battery Wiring?

I have new Li-ion batteries for my mac but i wasn't completely sure on how to wire it up to the old circuitry. I know that "vg" is the ground and the "vp" is the positive. I am assuming "vl" goes to the wire "vl" i dont know what that is thought.  But there is a "vh" spot on the new battery but on the old circuitry there was no wire going to there? Do I solder that wire there? There is also two very thin wires labeled ntc, i can not find a spot on the old circuitry for that is it necessary?

Question by Aaamazzara   |  last reply


Humbucker wiring?

I am rewiring my guitar, and on regular single-coil pickups, there is two wires, but on my humbucker, Three wires come out, a ground, a white and a red. and all my schematics have nothing to say about three wires being soldered. and i have a five-way switch, with eight hubs. i just dont know whereabouts to put the third red wire. please help

Question by ski4jesus   |  last reply


Wire Transistor?

How can I make a wire transistor? It needs to work quite well and has to be stable. Please help either with a picture and description or a schematic. Thanks to you guys in advance.

Question by tzq33tdq   |  last reply


fire wire

Hi if you do poi wid fire wire it looks so kool

Topic by mattadams   |  last reply


spinning wires?

I need to run some wires from the axel of my car to my rims, and i need to know how to have it so the wires can spin with the wheels, is there any way to do this?

Question by Sigsaucer647   |  last reply


Wiring Amps? Answered

How do you wire amps to speakers and a headphone jack?

Question by NatureBoom21   |  last reply


Wiring schematic?

Need wiring schematic for old Turf rider 4 golf cart, 36 volt, GE motor

Question by ejredmole   |  last reply


#16 wire

I have a schematic that says i need #16 wire to make an inductor, how do i find that size, what is the translation in mm? if anyone finds some could they give me a link please. thankyou

Topic by andrewlapham2010   |  last reply


Inspiration: wire

Http://www.lobzik.pri.ee/modules/news/article.php?storyid=790L

Topic by lemonie   |  last reply


Wired Then and Now

When I visited MITERS last month, someone was giving away their entire collection of Wired Magazine. I happen to have a current issue in my bag, and it was fun to compare their relative sizes. It's interesting that I also happen to be wearing a Digg shirt in the picture...

Topic by ewilhelm   |  last reply


Microphone wiring? Answered

I have a broken microphone. Its wire is cut  inside the insulation. i want to replace the entire cable. when i removed the plastic cover of the microphone i saw a red and a black wire soldered to it.  Therefore it uses only 2 wires but in the connector it is a TRS one not a TS one. i will also replace the connector.  i am wondering how should i wire a TRS connector which has 3 leads. one being the common ground. but the other 2.  should i short them out and connect the red wire or must I connect the wire to only one lead?  Then if i buy a $0.2 TS connector and i wire it accordingly. will it work? One another question does the microphone device has polarity that is should i connect  positive to positive and negative to negative lead. because there is no indication on the Mic?

Question by ARJOON   |  last reply


joystick wireing ? Answered

Hi , i need to wire a small joystick extracted from a toy remote control. It is life a ps2 joystick. it is working with 2 potentiometre. if you can make a picture It will be very nice

Question by copper tube   |  last reply


Headphone wiring

So I was trying to do some wiring with headphone jacks, and i must be doing something wrong. I have a speaker that the cord ripped from, and I wanted to attach a new jack, I cut off and stripped both wires, so there was a copper one and a colored one, why dont they work when they touch each other?

Topic by Weissensteinburg   |  last reply


Wire to Wireless? Answered

I purchased some XCam2 cameras, They are hard wired. Due to the need where to locate them, I would need them to become wireless. This is a great site along with some great minds. Thank you all for your input.

Question by Boriqua   |  last reply


Wiring help!

I have an 8th grade science class (I'm the teacher) that I would like to have construct underwater vehicles.  The kids will be using 9v batteries, switches and assorted other materials.  Does anyone know of any good books/articles that explain the basics of wiring, electricity, motors, switches, etc.  that I can have the students read to get a good base of knowledge in the basics of electronics? Thanks!!!

Topic by mashmtz   |  last reply


Disconnected Wires

So I'm working on a heart sensor, and pulled out the wires. I think I can fix it with a  little bit of solder, because after 20 or 30 minutes of negotiating, i can usually re-establish the connection to the sensor. But I tried just now, and it isn't working. Help??

Topic by kate1171   |  last reply


Wiring Question

Ok, I recently purchased a Go-Ped for practically nothing, and I really, really, really want to fix it up. I want to mount a couple of LED powered bicycle headlights on the front, and a tail light on the back. However, I want to be able to turn them all on and off via a single switch, mounted to the handlebars.I know very little about wiring, but I do know that most bicycle lights require physical pressure to power them on or off. Maybe there's something that can go between the batteries and bulbs?Any input you can provide would be fantastic!-Ryan

Topic by ryry214   |  last reply


microphone wiring?

Ok i was wondering if i took a microphone that was real cheap from walmart and take the male part off the end of it and put a female part so that way i can plug in a dual male sided cord to it and then to my computer, more or less im wondering, can it work like that? and then i was wondering if there is a program that when i plug the mic in that it works like plugging a guitar into an amp, as in it plays the input to the computer outloud without being in playback from a recording

Question by ClemensY290   |  last reply


Wiring question?

Hi everyone. Long time visitor of Instructables, made a few items I've seen and my most recent project was adding a star power pedal to my guitar hero controller. I bought a audio extension cable with a male and female jack, 1/8th size. I cut the cable about six inches from the female end. I stripped about an inch, inside was a bundle of copper wire wrapped around a clear insulted wire. I twisted the exposed copper wire and tinned it, I stripped the clear housing and twisted it, tinning them as well. I tinned the exposed wire to the GND, and the clear to Select. Positioned the jack and everything went well. I took the male cable, connected it to momentary switch and connected the male cable to the female jack. Turned on the system and controller. Got star power and hit the switch with no response. I'm very confident in my soldering and know I did it correctly, so I was wondering: 1) Are these kind of cables capable of doing what I intend? 2) Maybe the GND or the Select button are shorted out on the board of the controller? Thanks for any help everyone!

Topic by Mercenary Wubby   |  last reply


wiring help

Im working on a fireworks show and i just bought 25 toggle switches and led's from a garage sale for 5 bucks.. never opened still in packaging. how would i wire all this up to show when its armed a light would show on each channel.. im using this thing to ignite the bigger fire works (2 per switch)... i got around 360' of extra red insulated wire laying around from the shop i work at in the summer becasue they are throwing/giving away. any advice i also got a few rca and 1/8' male and femail jacks and a few push buttons from salvaged things... could i also use the thingys from cameras that put out 330 volts i have a few of those. you can contact me on meesenger also at:deer_hunt05@hotmail.com

Topic by pyroboy5   |  last reply


Dollhouse wiring

Hi All. I'm a believer in the idea that anyone can do anything with a little info. But I'm in need of a little help.  I'm building a dollhouse for my niece and would like to add a little higher-tech slant (she won't be playing with this for a few years yet...)  I would like to add LED lights (which I will make but just have to wire for at the moment), a flicker fireplace and a door bell all on wall mounted pushbutton switches.  Feel free to suggest anything else that might be cool for a kid... The whole system will run on a 12V adapter but since I need to wire this NOW so I can continue to build, I need a drawing or schematic of how to do it. I've attached a pic of the house and have been pulling apart some of the small flicker Tealights to kitbash into the fireplace.  I have a number of white LEDs with which to make the lights but they don't have to go in right now.  I know I'll need some resistors - where do I place them?  Hide them in the walls?  On each switch? Anyways - any help is so appreciated.  She'd never get anything like this unless I made it for her - I just want it to be so cool that her brothers are impressed! Tbird

Topic by Golftester   |  last reply


Wiring help

Hi guys I am need of some advice and help if possible, I will try and explain as clear as I can. I have a lockup which I have modified to use locking bolts on a motor and I have a swipe card reader and pcb which when swiped it fires the output to power the motor (6v) which works perfect for 6 seconds of the locking bolts going in and out. I am looking for a way so when the locking bolts go to the locked position it hits some kind of limit switch and stops there (which I have done in the past) but then I want to be able to swipe my card to open the bolts and when it gets to he open position it hits another limit switch and stays open until I want to swipe and close the locking bolts. I don't want this to be timed I need this to stop on open and closed position but able to operate when either is pressed, Can this be done in anyway?

Topic by sherpin2000   |  last reply


Wiring welder in the Philippines? ( 3 wire to 2 wire )

AI have a millermatic 211 which is a multi-voltage welder which I will be bringing to the Philippines. The adapter plugs are 5-15p (120v), and 6-50p (230v). Philippine electricity mains when I live are 220v single leg, with neutral. I am adding ground to both the Main panel and sub panel when I arrive, as most residential homes with a 2 wire system do not have them installed. According to the welder schematic  6-50p adapter configuration shows white, red, and green (ground) so goingfFrom a 3 wire US to 2 wire Philippine system is it proper to wire L1 to red, neutral to white and green to ground? 6-50 receptacle does not seem to incorporate a ground in typical installations????

Question by Antonioo35   |  last reply



4 wires fan to 2 wire

Hi guys, i need your help! I have an Enermax 12cm fan (EB122512H), i need to plug it to a 12v DC power supply but i don't know how to wire it; The fan has 4 wires (yellow, black, white, red) but the power supply has just two wires. could you help me?

Question by MichelS7   |  last reply


2 Wire Servo on 3 wire reviver? Answered

How can i wire a 2 wire servo into a 3 wire receiver I'm talking about the motor type, The reason i need to do this is because i need to get a cheap RC car on good radio gear

Question by Daniel Deacon   |  last reply


subwoofer installation? red wire, blue wire?

I need help with a car subwoofer, i have a friend whos red wire went, and doesn't have a power antenna akak a blue wire. his red wire went, its a 2000 buick and the cars are notorious for that issue. i have it on a switch for the 12v and i have a jumper from the 12v to the remote so when the switch is flicked the remote and 12 v are powered. is there an alternative wire to connect the remote to besides the red or blue?

Question by slimguy379   |  last reply


ni-cad wire

Does anybody know where to get some Ni-cad wire ?

Topic by joe12   |  last reply


EL Wire Needed

Is anybody giving away free EL Wire?

Topic by Loganbo   |  last reply


Nichrome wire problem...

Just have a little problem that im sure a lot of you have the answer... I try to put a Nichrome wire on come copper wire but the copper wire is always burning (when the Nichrome get red and hot [really need its ^^])so i lose the connection between the Nihrome wire and the copper wire....What should i do? use big fat copper wire?

Topic by koax   |  last reply


wire and bead tree

wire and bead tree tutorial

Topic by halla   |  last reply


EL Wire Troubleshooting

Hey everyone, I use EL Wires to make small neon signs and I've never had any problems with them until I started shipping them places. I have no idea how to fix these things and one of my customers told me the wire is detached from the transformer. Is this fixable?

Topic by kaybee71   |  last reply


What is 3d wire? Answered

I have heard this term from an instructables member and I would like to know what gauge if any I can use to ground my tesla coil.

Question by nerd7473   |  last reply


Wire Coat Hangers

How about someone come up with another use for all the wire coat hangers I have lying around? I am quite sure I am not the only person that has this problem, and I am equally sure there are WAY  many more intelligent inventors out there that could give me a lot of projects to do! Thanks!

Topic by thisismyrealname 


How to wire this transformer? Answered

ok, anyone know how to connect this transformer to mains power .. i get this from my UPS backup ..

Question by ishan udyoga   |  last reply


Wire ribbon roses?

Do you ever see those roses at the gas stations that are made of ribbon? the kind of ribbon that's sort of shear and has wire for the edges? I remember getting a closer look at it and seeing that the stem was wire as well and wrapped with shear non wire edged ribbon, but i have no clue as to how to make it.... I've been curious for a while but i don't think buying one and ripping it apart to see how it ticks would be exactly sufficient... could someone please make an instructable on this?

Topic by Lady Microfleegie II   |  last reply


Transformer-winding wire

I am going to be hand-wiring up a large lot of transformers. Someone has told me there is an enameled wire (magnet wire) whose coating melts when you dip it in solder (also tinning the copper tip at the same time). What is this type of wire called? I am having a hard time searching for it. Thanks!

Topic by samurai1200   |  last reply


How to wire this thing?

Hey Guys, Recently I bought a toy taser. After opening it and carefully observing it i accidentaly broke some of the connections. Can any one guide me on how to wire this capacitor/toroid or whatever this thing is? And will supplying 9v instead of 6v make the output higher?

Question by SA-DIY   |  last reply


Toxic Magnet Wire?

I know I'm probably going to sound like an idiot for asking, but can magnet wire release any toxic fumes when heated? I made a speaker using a magnet-wire coil and a neo-magnet, and when I plug it into the amp, I realized the coil gets very hot. I was expecting this, for I've used a number of coils in other projects. There is an odor, no doubt, that comes from every coil I've used when making an electromagnet. Sure, the smell may come from the iron nail being heated, but I always associate the smell with the coil. I'm not willing to smell this speaker, however. So, is there any risks that come from the heating of magnet wire? The coil gets hot after about a minute of run-time, but I'd like to be able to run through an entire album of music (an hour?) if possible. Thanks!

Topic by freethetech   |  last reply


Which wire is positive?

I have an electret mic that I want to use, but it has green and a black wires on it, would green be positive? Or would black be?

Question by Zem   |  last reply


Wires near a desk

I have a desk near my bed with the power strip on the other side of the desk. There's also my keyboard on the desk, so I have no problems in making the wires of my PC, phone, MP3 and 3DS chargers pass behind it so that they are hidden from view. I generally place my PC on the back of the keyboard and charge it, then everything else on top of either it or the keyboard. However, the things on the keyboard are quite ugly to the eye, while on the PC they clog. Also, it's always a pain to take the wire of the right charger (expecially in the dark), given that they are longer than the length of the desk, and if I roll them up they take up too much space. I was thinking of doing something to place those things on the side of the desk and fix the cables there. The problem is, I don't want to drill holes or anything like that, so I'm gonna stick with physics-fixed stuff or tape. What could I do that wouldn't be too bad to the eye?

Topic by Leodip   |  last reply


How to wire this laser? Answered

Hey Guys, I recently needed a laser for a project and as the electronics store had none i thought why non to extract one from a cheap laser diode. So....i got a laser peeled back the casing and got it. But the problem is that it doesnt work. Most probably because one of the contacts doesnt seem to be attached to the laser. Pics have been uploaded. Not that the lower contact doesnt seem to be connected with the rest (p.s it had a spring which used to come in contact with the underside of the button cells. I was wondering if any of you could help me.

Question by SA-DIY   |  last reply


Extending Servo Wire

I need to make a servo wire that extends approximately 4 feet and then retracts to a length of 18 inches or less. There is a risk of entanglement, so the less sag and less loose the wire, the better. One option would be to use coiled wire of the appropriate gauge, but a product such as this is expensive. What are some other options?One idea that I had was to build a wire spool mechanism like that of a tape measure. From what I understand, a tape measure uses a constant force spring to somehow apply a retractive force to the actual measuring tape. Can anyone provide a more clear explanation of how a tape measure retracts? Does anyone have any ideas of how to implement this into a wire spool? Other ideas on retracting a very long wire?Thanks

Question by icecats   |  last reply


Wire Wrapping Kits

I can make you a kit for any of my wire jewelry projects. I have the nest and the basic cab kits already, since I teach those, but I can assemble what you need for any of my wire jewelry instructables. Gemstones will be whatever is in my studio at the time, though you can tell me what kinds of things you like. This will hopefully take the anxiety out of not knowing how to get started. Kits usually cost about $3o - $40 plus shipping. Just contact me through instructables if you want one.

Topic by Rhonda Chase Design 


The Weekly Challenge: Wire

OFFICIAL RULES PLEASE REVIEW THESE OFFICIAL RULES BEFORE ENTERING THE CONTEST. ENTRANTS WHO ARE MINORS: YOU MUST OBTAIN THE CONSENT OF YOUR PARENT OR LEGAL GUARDIAN BEFORE ENTERING THE CONTEST. ENTRY TO THE CONTEST IS FREE AND NO PAYMENT OR PURCHASE IS NECESSARY TO ENTER OR WIN. A PAYMENT OR PURCHASE WILL NOT IMPROVE YOUR CHANCES OF WINNING. VOID WHERE PROHIBITED BY LAW. PLEASE SEE THE INSTRUCTABLES TERMS OF SERVICE AND PRIVACY POLICY SECTION A - SPECIFIC TERMS FOR THIS CONTEST Sponsor. The Instructables The Weekly Challenge: Wire (the "Contest") is a skill-based contest sponsored by Instructables, Inc., a Delaware corporation ("Sponsor"), in connection with the Instructables.com website (the "Sponsor Site"). The Contest is co-sponsored by the company or companies listed here, if any (each, a "Co-Sponsor"): none. The Contest is governed by these Official Rules (these "Rules"). Overview. The object of the Contest is to make anything using wire of any sort. Eligibility. 1.THE CONTEST IS OPEN ONLY TO NATURAL PERSONS WHO, AT THE TIME OF ENTRY, ARE REGISTERED MEMBERS OF THE SPONSOR SITE, WHO ARE AT LEAST THIRTEEN (13) YEARS OLD, AND ARE LEGAL RESIDENTS OF THE 50 UNITED STATES (INCLUDING THE DISTRICT OF COLUMBIA BUT EXCLUDING PUERTO RICO),  CANADA (EXCLUDING THE PROVINCE OF QUEBEC, CANADA), UNITED KINGDOM, OR AUSTRALIA. 1.If you are a minor, meaning that you are under the age of majority in your jurisdiction (currently 18 or 19 in most U.S. states and provinces of Canada and Australia, and, for the UK, 16 in Scotland and 18 in most other parts of the United Kingdom), you must obtain permission from your parent or legal guardian, and your parent or legal guardian must consent to these Rules as if he or she were an entrant, before you submit an entry.  Sponsor reserves the right to require minors to submit proof of parental/guardian permission and consent to these Rules at any time, without which they may be immediately disqualified from the Contest. Certain individuals are excluded from eligibility to enter or win, as described in Section B below.  No purchase is necessary to enter the Contest. Deadline. The Contest begins at 12:00 a.m. Pacific Time (PT)/8AM GMT on November 28th, 2011 (the "Start Date"). Entries for the Contest must be received by Sponsor by 11:59 p.m. PT on December 4th, 2011 /7:59am GMT on December 5th, 2011 (the "Deadline"). How to Enter. All entries must comply with the entry requirements identified in these Rules (including in this Section and in Section B below), as well as with any specific formatting or content requirements identified in Section A.2 above or on the "How to Enter" page https://www.instructables.com/id/The-Weekly-Challenge-Wire/ for the Contest on the Sponsor Site. It is each entrant's responsibility to ensure compliance with those requirements. To enter a new project in the Contest, follow these steps: First document your project in the step-by-step or photo,Instructables format. When your project is ready to be published to the Sponsor Site, visit the Sponsor Site and follow the instructions for publishing your project to the Sponsor Site.  You must be a registered user of the Sponsor Site in order to publish a project to the Sponsor Site. If you are not already a registered user of the Sponsor Site, you will be prompted to create an account on the Sponsor Site during the publication process. Please note: in some jurisdictions, the publication of your project on the Sponsor Site could materially affect rights (e.g., adversely affect patent rights), you may own in the project.  You should make your own inquiries and seek your own advice on this issue. When you have published your project to the Sponsor Site, if you have reviewed the entry requirements for the Contest, believe your project qualifies for entry, and want to enter it in the Contest, leave a comment on the Contest page, and include a link to your published Instructable. Instructable must be published during the Contest period. You may not enter the same Instructables project in more than three (3) Instructables contests in total. Projects published prior to the Start Date are not eligible for entry.  You may not register the same Instructables project in more than three (3) Instructables contests in total. Further information about entry can be found in Section B below. Winner Selection. There can be up to 11 possible winning entries, depending on the number of eligible entries. The winning entries will be selected on or around December 5th, 2011, and Sponsor will announce the winner(s) on or around December 5th, 2011. There must be a minimum of the number of eligible entrants described for each tier listed below for it to be awarded.  Each winner will be awarded only the applicable prize according to the following: Prize(s). Tier #1: If there are at least 5 but no more than 9 eligible entries, the winner will be awarded a prize package including a 1-year Instructables Pro membership, and a Sugru sample pack.  Approximate retail value: $50, £ 32.31; or Tier #2: If there are at least 10 but no more than 24 entries, the winner will be awarded a prize package including a 1-year Instructables Pro membership, a Sugru sample pack, and an Instructables robot t-shirt.  Approximate retail value: $65, £ 42; or Tier #3: If there are at least 25 but no more than 49 entries, the entrant with the highest judges’ score will be awarded a prize package including a Leatherman Juice, a 1-year Instructables Pro membership, a Sugru sample pack, and an Instructables robot t-shirt.  Approximate retail value: $105, £ 67.86.  The entrants with the next 3 highest judges’ scores will each be awarded a prize package including a 1-year Instructables Pro membership, a Sugru sample pack, and an Instructables robot t-shirt.  Approximate retail value of each prize package: $65, £ 42; or Tier #4: If there are at least 50 but no more than 99 entries, the entrant with the highest judges’ score will be awarded a prize package including a Dremel rotary took kit, a 1-year Instructables Pro membership, a Sugru sample pack, and an Instructables robot t-shirt.  Approximate retail value: $165, £ 106.64.  The entrants with the next 5 highest judges’ scores will each be awarded a prize package including a 1-year Instructables Pro membership, a Sugru sample pack, and an Instructables robot t-shirt.  Approximate retail value of each prize package: $65, £ 42; or Tier #5: If there are 100 or more eligible entries, the entrant with the highest judges’ score will be awarded a prize package including an iPad 2, a 1-year Instructables Pro membership, a Sugru sample pack, and an Instructables robot t-shirt.    Approximate retail value: $565, £ 365.15. The entrants with the next 10 highest judges’ scores will each be awarded a prize package including a 1-year Instructables Pro membership, a Sugru sample pack, and an Instructables robot t-shirt.  Approximate retail value of each prize package: $65, £ 42. With respect to any prizes that include any gift cards, pre-paid debit cards,  similar cards, or any other items or services that are subject to third party terms and conditions or restrictions, acceptance and use of the prizes are subject to all eligibility criteria, expiration dates, service or dormancy fees, and all other terms and conditions (if any) imposed by the issuer of such cards, items or services. Neither Sponsor, nor any Co-Sponsor, nor any of their affiliates is the issuer of any such cards, items or services, and none of them are responsible for establishing those terms and conditions, for disclosing or explaining any of those terms and conditions to entrants, or for any winner's failure to comply with any of them.  If a winner does not comply with all of those terms and conditions, the winner may not be able to obtain the maximum value, or any value, from his or her prize. The estimated retail value of all prizes to be awarded in the Contest depends on the number of eligible entries and is between: $50 - $1,215, £ 33.21 - £ 785.24. Judging. 1.Entries will be judged on the basis of the following criteria (the "Criteria"):  relevance, originality, usefulness, simplicity, and clarity of instructions, each of which will be given equal weight.  Entrants will be judged by the Randy Sarafan. Further information on the steps and process of voting and judging can be found in Section B below. Odds of Winning. The odds of winning a prize depend on the number of eligible entries received between the Start Date and the Deadline and the quality of each entry as evaluated by the Judge in the manner described above.  The number of entries received, and the number of winners chosen, in prior contests of Sponsor, including the three (3) most recently completed contests, can be found through the "Contests" page of the Sponsor Site, which can be found here instructables.com/contest.  The number of eligible entries for Sponsor's recently completed contests generally has ranged from approximately two (2) to approximately eighty-three (83), and generally has averaged approximately forty (40), but Sponsor cannot predict or guarantee any specific number of eligible entries for the Contest.   SECTION B - ADDITIONAL TERMS FOR THIS CONTEST General Conditions. By entering the Contest, each entrant agrees to abide by the terms of these Rules and by the decisions of Sponsor and the Judges, which shall be made in all cases in their sole and absolute discretion and are final and binding on all matters relating to the Contest. The Contest is governed by the laws of the State of California and applicable United States federal law, without regard to any conflicts of laws principles. The Contest is void where prohibited by law. The Contest is also governed by Sponsor's Terms of Use, Privacy Policy, and other policies (collectively, the "Policies") pertaining to the Sponsor Site, although the Rules will govern any conflict between the Privacy Policy and the Rules. Exclusions from Eligibility. Employees of Sponsor, any  Co-Sponsor, or their respective parents, subsidiaries, affiliates, partners, suppliers, or advertising or promotional agencies (including without limitation any Judges who are employees of Sponsor, any Co-Sponsor or any of their respective parents,     subsidiaries, or affiliates), as well as members of their households or their immediate families, may submit entries in the Contest, but any such entries are for information and entertainment purposes only and are not eligible to be considered for the purpose of selecting finalists or winners.  Judges who are not employees of Sponsor, any Co-Sponsor or any of their respective parents, subsidiaries, or affiliates, are not eligible to enter or win, nor are members of their households or their immediate families.   Entry. 1.Multiple entries are permitted, but only one entry per entrant can win a prize in the Contest.  Entrants must be registered users of the Sponsor Site to enter the Contest.  Registering for an account with the Sponsor Site may require each entrant to submit entrant's name, e-mail address, age or date of birth, and other details, and in the case of a minor, contact details for a parent or legal guardian for purposes of obtaining proof of parental consent, if Sponsor elects to do so.  Entries can be the work of more than one person, but for purposes of the Contest, each entry will belong to the "Primary Author" named in the entry, regardless of the number of contributors to that entry.  For winning entries, Sponsor will award the applicable prize to the named entrant only, and will not be responsible or liable for apportioning any prize among contributors to a winning entry.  Upon submission, all entries become subject to the Policies (including without limitation the provisions regarding ownership and use of user submissions as stated in the Terms of Use https://www.instructables.com/tos.html).  Entries will not be acknowledged or returned.  Entrants are permitted to modify or update an entry after submission, but are not permitted to do so after the Deadline.  Entries may remain posted on the Contest page of the Sponsor Site indefinitely following the Deadline, but Sponsor reserves the right to delete entries from the Contest page after the Contest ends, in its discretion.  Entries may not be created or submitted through any software-generated, robotic, programmed, script, macro, or other automated method.  Sponsor and Co-Sponsor will have no responsibility for, and will have the right to refuse in its discretion, any entries that have been tampered with, or entries that are misdirected, incomplete, non-conforming, corrupt, lost, late, or ineligible, whether due to Internet or e-mail server failure or otherwise.  Proof of transmission of an entry shall not constitute proof of receipt.  It is each entrant's responsibility to keep Sponsor informed of any changes to entrant's contact or other information during the Contest. Additional Entry Requirements. Each entry must comply in all respects with the Policies, including without limitation all requirements for user submissions, as stated in the Terms of Use https://www.instructables.com/tos.html for the Sponsor Site. Without limiting that requirement, each entry also must comply with the following: Each entry must be entirely the original work of the persons identified in the entry; If persons other than the entrant have contributed to an entry, the entrant must have the permission from each contributor prior to submitting the entry; Entries must not have been published prior to the Start Date; Entries must not have been entered in more than two other previous contests of Sponsor; Entries must not contain anything that is or may be: (i) threatening, harassing, degrading or hateful; (ii) defamatory; (iii) fraudulent or tortious; (iv) obscene, indecent or otherwise objectionable; or (v) protected by copyright, trademark or other proprietary right without the express prior consent of the owner of such right; and Entries must not contain any material that would give rise to criminal or civil liability or that encourages conduct that constitutes a criminal offense. Judging Process. The winner(s) will be determined by the Judges, who will apply the Criteria to evaluate entries. The entries with the highest score(s) will be selected as the winner(s), and the number and type of winners will be as identified in Section A above. The Judges have the right to disqualify any entry that is not in compliance with these Rules, in the Judges' discretion. In the event that a winning entry is disqualified, the next-highest scoring entry will be selected as the alternate winner.  In the event that one or more of the identified Judges is unavailable, Sponsor reserves the right to substitute Judges of comparable qualification, to be determined by Sponsor in its discretion. Prize Terms All values are stated in United States dollars or British Pound Sterling as indicated.  If a stated  prize is unavailable, Sponsor has the right to substitute one or more items of equal or greater value, in its discretion.  No prize is exchangeable, transferable, or redeemable for cash.  The winner(s) will be solely responsible for complying with any and all     applicable statutes, laws (including, without limitation, common law), rules and regulations and for bearing any personal income, VAT, withholding taxes, customs duties, or other taxes, fees,     insurance, surcharges or other costs relating to any prize. THE PRIZE(S) WILL BE GIVEN AWAY BY SPONSOR AND ANY CO-SPONSOR(S) "AS IS."  SPONSOR AND ANY CO-SPONSORS DO NOT MAKE, AND EXPRESSLY DISCLAIM, ANY WARRANTY, WHETHER EXPRESS, IMPLIED, OR STATUTORY, REGARDING ANY PRIZE OR PORTION THEREOF, INCLUDING WITHOUT LIMITATION ANY IMPLIED OR STATUTORY WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, TITLE, OR NON-INFRINGEMENT.  SOME JURISDICTIONS MAY NOT ALLOW THE EXCLUSION OF IMPLIED WARRANTIES, CONSUMER GUARANTEES AND SIMILAR RIGHTS, IN WHICH CASE SUCH EXCLUSION SHALL APPLY ONLY TO THE EXTENT PERMITTED BY APPLICABLE LAW IN THE RELEVANT JURISDICTION. WITHOUT LIMITATION, TO THE FULLEST EXTENT PERMITTED BY APPLICABLE LAW, ALL WARRANTIES AND REPRESENTATIONS, IN RELATION TO THE PRIZES, WHETHER EXPRESS OR IMPLIED BY STATUTE, LAW (INCLUDING, WITHOUT LIMITATION, COMMON LAW), RULE, REGULATION OR OTHERWISE, ARE HEREBY EXCLUDED.   Announcement; Award of Prize(s). 1. The winner(s) will be notified by e-mail within seven (7) days of selection.  The winner(s) (and, if a winner is a minor, the winner's parent or legal guardian) may be required to sign a declaration of eligibility and/or publicity and/or liability release form, to the extent not prohibited by law, prior to receipt of a prize.  The winner(s) must take possession of the prize(s) as directed by Sponsor.  The winner(s) may be required to provide Sponsor with a social security or taxpayer identification number for tax purposes.  The winner(s) also may be required to provide Sponsor with proof that he or she is the Authorized Account Holder of the e-mail address associated with the winning entry.  An "Authorized Account Holder" is the natural person who is assigned to an e-mail address by an Internet access provider or other organization responsible for assigning e-mail addresses to the domain associated with an e-mail address.  In the event of a dispute, an entry will be deemed to have been submitted by the Authorized Account Holder of the e-mail address submitted at the time of entry.  Failure to respond to a winner announcement, or return any required declarations or releases within seven (7) days (or any longer time specified by Sponsor) or to comply with any of the foregoing may result in disqualification and the selection of an alternate winner.  It is Sponsor's policy to assist government employees in meeting their obligations under their Standards of Ethical Conduct; any prize(s) won in violation of those Standards should not be accepted and should be returned at Sponsor's expense or destroyed. Representations. 1.By entering the Contest, each entrant represents and warrants that: (a) the entrant meets all eligibility requirements of the Contest; (b) in entering and participating in the Contest, the entrant has complied and will comply in all respects with these Rules and all applicable statutes, laws (including, without limitation, common law), rules and regulations; and (c) the information provided in the entrant's entry, including without limitation all contact information, is true, accurate, and complete in all respects.   Assumption of Risk.  By taking any action to create an entry for the Contest, each entrant, on his or her own behalf and on behalf of his or her personal representatives, heirs, executors, and assigns, acknowledges and agrees that: (a) THERE MAY BE DANGER     AND RISK OF BODILY INJURY, DEATH, OR PROPERTY DAMAGE INVOLVED IN CREATING AN ENTRY; (b) THESE RISKS AND DANGERS MAY ARISE FROM FORESEEABLE OR UNFORESEEABLE CAUSES; (c) SUCH ENTRANT AND HIS OR HER PERSONAL REPRESENTATIVES, HEIRS, EXECUTORS, AND ASSIGNS ASSUME ALL RISKS AND RESPONSIBILITY FOR ANY PERSONAL INJURY, DEATH, PROPERTY DAMAGE, OR OTHER LOSS ARISING OUT OF THE CREATION OF ANY ENTRY, WHETHER CAUSED BY NEGLIGENCE OR ANY OTHER CAUSE; and (d) such entrant and his or her personal representatives, heirs, executors, and assigns are relinquishing any and all rights he, she, or they now have or may have in the future to sue or take any other action against Sponsor, any Co-Sponsor, the prize manufacturers, any other entities involved in the administration of the Contest, each of their respective parents, subsidiaries, and affiliates, and each of their respective officers, directors, employees, agents, and representatives (the “Sponsor Parties”) on the basis of any injury, death, damage, or other loss that may be suffered arising from any action taken in the creation of any entry,     including but not limited to claims based on allegations of negligence by any of the Sponsor Parties.       Release. To the maximum extent permitted by law, by entering the Contest, each entrant releases and holds harmless the Sponsor Parties from any and all responsibility,     liability, damages  (including, without limitation, direct, indirect, incidental, consequential, punitive, statutory, and other damages), losses, costs, or expenses of any kind arising out of or     relating to: (a) entry or participation in the Contest, including but not limited to disputes among individuals claiming to have contributed to any winning entry; (b) any violation by the entrant     of these Rules, the Policies, or applicable laws; (c) misappropriation, infringement, or other violation of any copyright, trademark, patent, trade secret, right of publicity, privacy, or other legal or contractual right of any person attributable to entrant or any entry submitted by entrant; (d) the acceptance, possession, receipt, or use of any prize or any item purchased with any prize (e.g., if the prize includes a gift card); (e) any entries or votes that have been tampered with or that are misdirected, incomplete, non-conforming, corrupt, lost, late, or ineligible; (f)     any problems or technical malfunctions (including but not limited to errors, omissions, interruptions, deletions, defects, or delays in operation or transmission) of any computer, telephone, modem, cable, satellite, network, hardware, online system, server, software, or     other equipment or provider, including any incorrect, incomplete, garbled or jumbled information resulting therefrom; (g) any Internet traffic congestion or website accessibility or delays; (h) printing or typographical errors in any Contest-related materials; or (i) any other technical or human error that may occur in connection with the Contest (the “Causes”).  If anyone makes any claim against any of the Sponsor Parties arising out of or relating to any of the Causes attributable to the entrant, the entrant will pay for any damages, losses, liabilities, costs, penalties, and expenses, including without limitation attorneys’ and experts’ fees and costs, incurred in connection with such claim. WITHOUT LIMITING THE GENERALITY OF THE FOREGOING, THE SPONSOR PARTIES SHALL NOT BE LIABLE FOR ANY LOST PROFITS OR ANY SPECIAL, INCIDENTAL, INDIRECT, PUNITIVE, EXEMPLARY, OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE CONTEST, HOWSOEVER CAUSED, WHETHER ARISING IN STATUTE, TORT, CONTRACT, OTHER LEGAL THEORY OR OTHERWISE, AND ALL SUCH DAMAGES ARE HEREBY DISCLAIMED AND EXCLUDED.  SOME JURISDICTIONS MAY NOT ALLOW THE LIMITATION OR EXCLUSION OF LIABILITY FOR DAMAGES AND OTHER     LIABILITY (INCLUDING INCIDENTAL OR CONSEQUENTIAL DAMAGES) IN WHICH CASE SUCH LIMITATION OR EXCLUSION SHALL APPLY ONLY TO THE  FULLEST EXTENT PERMITTED BY APPLICABLE LAW, RULE, STATUTE OR REGULATION IN THE RELEVANT JURISDICTION. NOTHING IN THESE TERMS EXCLUDE LIABILITY FOR FRAUD, OR FOR PERSONAL INJURY OR DEATH CAUSED BY NEGLIGENCE TO THE EXTENT SUCH EXCLUSION IS PROHIBITED BY     APPLICABLE LAW.       Misconduct. Sponsor reserves the right, in its discretion, to disqualify any entrant who: (a) tampers with the entry or voting process, the operation of the Contest, the Sponsor     Site, or affiliated websites; (b) acts in an unsporting or disruptive manner, or with intent to annoy or harass another person; (c) is otherwise in violation of these Rules, the Policies, or any     applicable laws; or (d) attempts to subvert the letter and/or spirit of these Rules. SPONSOR RESERVES THE RIGHT TO SEEK DAMAGES FROM ANY SUCH PERSON TO THE FULLEST EXTENT PERMITTED BY LAW.   Termination. 1.Sponsor reserves the right to suspend, modify, or terminate the Contest at any time for any reason, in its discretion, including without limitation in the event of fraud, abuse, tampering, technical, administrative, financial, or other difficulties.  In such cases, Sponsor will post a notice on the Contest page of the Sponsor Site.  Should the Contest terminate prior to selection of the winner, Sponsor will announce an alternate means of awarding the prize on the Contest page of the Sponsor Site.   Advertising. By entering the Contest, each entrant grants to Sponsor the rights to use his or her entry as provided in the Policies, including without limitation the provisions of the Terms of Use https://www.instructables.com/tos.html regarding ownership and use of user submissions.WITHOUT LIMITING THE FOREGOING, TO THE MAXIMUM EXTENT PERMITTED BY LAW, BY ENTERING THE CONTEST, EACH ENTRANT CONSENTS, AND WARRANTS THAT IT HAS OBTAINED THE WRITTEN CONSENT OF EVERY CONTRIBUTOR TO THE ENTRY,  TO THE USE BY SPONSOR, ANY CO-SPONSOR, OR ANY THIRD PARTY CHOSEN BY SPONSOR OR ANY CO-SPONSOR, OF ANY AND ALL INFORMATION, DRAWINGS, TEXT, PHOTOS, VIDEOS, OR OTHER MATERIAL CONTAINED IN AN ENTRY OR OTHERWISE  PROVIDED BY SUCH ENTRANT RELATED TO THE CONTEST, INCLUDING ANY PERSONAL INFORMATION OBTAINED THROUGH THE CONTEST, FOR ADVERTISING, MARKETING OR ANY OTHER PURPOSES NOT PROHIBITED BY LAW. Otherwise, each entrant retains whatever rights it may have in each entry to the extent provided in the Policies.  To the maximum extent permitted by law, by accepting a prize, a winner consents on his or her own behalf and on behalf of any contributor to the entry, to the print and online publication of the winner’s user name, first and last name, address, and winning entry as part of the official winner's list and also to the use of his or her winning entry, first and last name, user name, voice, photograph, biographical material, and likeness by Sponsor, any Co-Sponsor, or any third party chosen by Sponsor or any Co-Sponsor, for advertising,     marketing, and other purposes without additional compensation.      Other than as set forth herein, Sponsor will treat any personal     information supplied by entrants in connection with the Contest in     accordance with Sponsor's Privacy Policy   https://www.instructables.com/about/privacy.jsp. Miscellaneous. 1.Other than for entrants who are U.K. residents, Sponsor, any Co-Sponsor, and each entrant agree to the non-exclusive jurisdiction of an appropriate state court in Marin County, California, or an appropriate federal court located in San Francisco, for any action or proceeding arising out of or related to these Rules, the Contest, or any prize.  For U.K. residents: these Rules are governed by the Laws of England and Wales, and Sponsor, any Co-Sponsor, and each entrant agree to the non-exclusive jurisdiction of the courts in England in connection with any action or proceeding arising out of or related to these Rules, the Contest, or any prize.  By entering the Contest, each entrant submits to the jurisdiction of those courts and waives any objection to those courts, whether on the basis of jurisdiction, venue, inconvenience of the forum, or otherwise.  If any part of these Rules is held by a court of competent jurisdiction to be invalid, illegal, or otherwise unenforceable, such part will be modified by such court to the minimum extent necessary to make it enforceable while preserving to the maximum extent possible the original intent of Sponsor, and the remaining parts of these Rules will remain in full force and effect.  Nothing contained herein or in any of the Contest related materials should be construed as an endorsement by Sponsor of any Co-Sponsor, or of Sponsor or any Co-Sponsor of any third party, product, or service. Winner's List; Mailing List. The user name(s) and entries of the Contest winner(s) will be posted on the Contest page of the Sponsor Site, within thirty (30) days of awarding of all prizes.  In addition, the names of the winner(s) may be obtained by sending a written request and a self-addressed, stamped envelope to the below address (requests must include the words "WINNER'S LIST" and the full name of the Contest prominently in the first line of the address): Instructables 82 2nd St.   San Francisco, California 94105 USA All such requests must be received within six (6) months of the Deadline.  Sponsor's telephone number for Contest purposes is (01-510-473-7626).  Entrants who opt to join Sponsor's electronic mailing list agree to be contacted by email by Sponsor.  Requests for removal from Sponsor's mailing list may be made as instructed in any such email, or by sending a written request and a self-addressed, stamped envelope to "Instructables Mailing List" at the above address, by calling the above telephone number, or as otherwise indicated on the Sponsor Site.  Residents of Vermont may omit return postage on winner's list and mailing list requests.    © 2011 Instructables, Inc. All rights reserved. INSTRUCTABLES is a registered trademark of Instructables, Inc. Other brands may be trademarks of their respective owners.

Topic by randofo   |  last reply


wire electric in house?

Question by acherryl   |  last reply