is there a way to melt rubber and steel together?

I've been thinking about this for a long time. What I am wanting to accomplish is finding a way to combine steel and rubber together to form a new substance where the two are no longer able to be distinguished from each other.

Question by Jakcavar   |  last reply


K'nex Combination Lock

I got bored and decided to show off my combination lock here at Ibles. It's not done yet, but here it is: http://s271.photobucket.com/albums/jj128/Mepain/KI/?action=view&current;=SMOV0022.flv

Topic by Mepain   |  last reply


Combining PC with.....A FAN!

This idea just popped into my brain last nite.Why not use strong automobile fans to cool the PC?Just mount it on the panel(geek points for duct tape)and off u go!Most engine fans run on 12VDC now and a pc has that,then SPLICE THE TWO TOGETHER!Advice and flaming will be appreciated

Topic by Derin   |  last reply


coMBINING ARDUINO SKETCHES

Every thing is okay except line follow command ,,,when i say line follow it only goes forward but does not follow line my code is String voice; int LS=10; int RS=9; int LED=13; char getstr; int in1=3; int in2=4; int in3=5; int in4=6; int ENA=2; int ENB=7; long duration, distance; int trigPin=A0; int echoPin=A1; int buzzer=8; void forward() {   digitalWrite(ENA,HIGH);   digitalWrite(ENB,HIGH);   digitalWrite(in1,HIGH);   digitalWrite(in2,LOW);   digitalWrite(in3,LOW);   digitalWrite(in4,HIGH);   } void back() {   digitalWrite(ENA,HIGH);   digitalWrite(ENB,HIGH);   digitalWrite(in1,LOW);   digitalWrite(in2,HIGH);   digitalWrite(in3,HIGH);   digitalWrite(in4,LOW);   } void left() {   digitalWrite(ENA,HIGH);   digitalWrite(ENB,HIGH);   digitalWrite(in1,LOW);   digitalWrite(in2,HIGH);   digitalWrite(in3,LOW);   digitalWrite(in4,HIGH);   } void right() {   digitalWrite(ENA,HIGH);   digitalWrite(ENB,HIGH);   digitalWrite(in1,HIGH);   digitalWrite(in2,LOW);   digitalWrite(in3,HIGH);   digitalWrite(in4,LOW);   } void stop() {   digitalWrite(ENA,LOW);   digitalWrite(ENB,LOW);   } void on() {   digitalWrite(LED,HIGH); } void off() {   digitalWrite(LED,LOW); } void line(){ if(digitalRead(LS) && digitalRead(RS))     // Stop   { stop();   }     if(!(digitalRead(LS)) && digitalRead(RS))     // right   { right();   }     if(digitalRead(LS) && !(digitalRead(RS)))     // Turn left   { left();   }     if(!(digitalRead(LS)) && !(digitalRead(RS)))     // Forward   {     forward();   } } void setup() {   pinMode(LED, OUTPUT);   Serial.begin(9600); pinMode(LS, INPUT);   pinMode(RS, INPUT);   pinMode(in1,OUTPUT);   pinMode(in2,OUTPUT); pinMode(trigPin, OUTPUT); pinMode(echoPin, INPUT);   pinMode(in3,OUTPUT);   pinMode(in4,OUTPUT);   pinMode(ENA,OUTPUT);   pinMode(ENB,OUTPUT); pinMode(buzzer, OUTPUT); } void loop() {   while (Serial.available()){ //Check if there is an available byte to read      delay(10); //Delay added to make thing stable     char c = Serial.read(); //Conduct a serial read     if (c == '#') {break;} //Exit the loop when the # is detected after the word     voice += c; //Shorthand for voice = voice + c   }   if (voice.length() > 0){     if(voice == "*go ahead"){       forward();       }     else if(voice == "*go back"){       back();       }     else if(voice == "*turn right") {       right();     }     else if(voice == "*turn left") {       left();     }     else if(voice == "*light on") {       on();     }     else if(voice == "*light off") {       off();     }         else if(voice == "*stop") {       stop();     } else if(voice == "*line follow") { line();           }       voice=""; //Reset the variable after initiating   } }

Topic by BibekP4   |  last reply


Combine 2 powerbanks for mobile

Hello, I have 2 old powerbanks that didn't have enough cappacity. So I want to combine the 2. But both have 5v 800ma output. So if I am afraid that the voltage or the ampere will be to high. How can I combine the 2 without damaging my phone? Sorry for my bad english. Greeting, Thijs

Topic by Thijsd4   |  last reply


flash drive and radio combined?

Does anyone know how to make an mp3 from portable radio and flash drive? thank you

Topic by redon12   |  last reply


Combining (Rewiring) Earphones Together

Hello! I'm having trouble rewiring my Ipod earphones. Currently I have two sets of nonworking earphones. One is an Ipod 3rd generation earphones. Pretty standard, ones you can find anywhere. The earbuds are completely busted on this one, and thus it does not work. The second one is Iphone earphones, and thus has a little mic component along the right earphone cord. This one, the bottom jack is completely busted. What I want to do this cut and combine the bottom 1 inch (including the jack) of my ipod earphone with my Iphone earphones. I understand this will render the mic capability useless. The ipod earphones have 4 wires inside, yellow, red, green, and red/green. The iphone ones have 6 wires. green, blue, yellow, red, red/yellow, and another yellow. How do I match these up to work? Thank you so much in advance!

Topic by lazda 


how to power multiple fans from a laptop? Answered

I'm currently working on a laptop to somewhat of a desktop conversion.  The laptop has really bad cooling so i have drilled into the case and added some big fans.  Its probably overkill yes, but if it works then who cares.   I've added two fans.  One is a 24V DC .20A fan and the other is a regular DC motor.  I'm wanting to power them from the laptop.  I'm not sure how to do that though.  I've tested them both separately on a USB and they are very slow and almost useless.  Is there a way to combine two USB ports for more juice?  Any ideas or suggestions?  Thanks.

Question by knex.gun.builder   |  last reply


The ultimate combination of woodworking, music, and ingenuity

This was sent to me and I thought it was well worth sharing. An impressive project.  http://

Topic by Vyger   |  last reply


Cant combine my two acccounts

It seems that along the line somwhere i have been given a second login for instructables. this one im on now i can download PDFs and it seems i have full pro membership. the one i can login with my facebook however, i have not got pro membership. how do i combine the two? the facebook login one is called Joypad570

Topic by joypad   |  last reply


Combining AC and DC on the one output?

I have a variable 0-12v DC output which has a maximum output of 1 amp. I have a fixed 16v AC output which has a maximum output of 1 amp. I am looking at how to combine the two so as to power a model with the variable DC output and also power lighting on the AC through a capacitor to filter the DC out. Also, I would rather it was nearer 6v AC at the output. Would this just be a matter of a simple step-down transformer before they are combined? Essentially, I am looking to replicate the functionality of this product for less than £42.95. This is too expensive especially when I need two of them.

Question by gkilgour   |  last reply


Need some good color combinations

Got some new wheels for my bike that were dirt cheap..Only problem is I need some good colors that will make the bike look amazing. The rims are yellow and the spokes are black. Help me out. Be creative.

Question by lieks2bhugged   |  last reply


Panasonic Palmcorder and Webcamera combined into one?

Hello, I'm slightly new to this site but I love the heck out of it. I was wondering if it would be possible to remove the lens out of an old (from like 1995) panasonic palmcorder and put it into a webcam. I'm into brickfilming and I'm getting tired of my webcam's crappy foucus.Here is a picture of the lens from the palmcorder and all it's connections. [img]http://www.brickshelf.com/gallery/No-one-at-all/tests/dsc_0001.jpg[/img][img]http://www.brickshelf.com/gallery/No-one-at-all/tests/dsc_0002.jpg[/img][img]http://www.brickshelf.com/gallery/No-one-at-all/tests/dsc_0003.jpg[/img][img]http://www.brickshelf.com/gallery/No-one-at-all/tests/dsc_0004.jpg[/img]

Topic by -ddrblank-   |  last reply


Bass (guitar) signal spilt + combine

Hello I have been thinking about a project that I would like to try. The idea is that I would like to be able to take the signal from my bass guitar and split it in two (configurable how much signal in each, but the sum should be 100%), apply an effect to one of the lines and then combining the two signals again having only applied the effect to some of the signal while carrying the clean signal through. This way I could apply e.g. distortion to only 20% of the signal. I thought that I could control the volume simply by putting an resistor in the signal line, but this gave quite some noise. This is my first attempt at building electronics for instruments, but have some experience with electronics in general. Hope you can help me with a couple of questions: 1) Shouldn't you be able to lower the signal simply by resistors? Should you use any specific resistors for audio? 2) Is it possible to recombine two audio signals and can you just put the wires together? Kind Regards Brian

Topic by FatMooseHenry   |  last reply


New Sport!! Combine Golf with Archery!

I have an idea for a new sport. If you combine golf with archery, you'd get Golfery! The concept is simple with only some minor modifications. Arrowheads now have a golf ball or ping-pong ball for a head. To get a hole in one, the player must hit the flagpole in the pocket. There are (3) 1 foot wide rings concentrically spaced around the flagpole. Inner ring = 1 stroke, middle = 2 strokes, outer = 3 strokes. If the arrow lands outside of the outer ring, the player must pick up the arrow and gently toss it underhand towards the pocket. Other than that, the standard rules of golf are followed. I don't have the equipment to test out my ideas. If someone here would try it out and PM me with the results and any suggestions that would be great.

Topic by javajunkie1976   |  last reply


Help with LED combination to make a face.

Hi,      I am trying to make a face using LEDs.  I have attached an image of what I want to make.  Referring to the image the first set of Led will fade in one by one and then stays on while the next set of LEDs fade in one by one.  This will continue until all the sets for the mouth LEDs have been faded in.  Then the eyes, white LEDs in the outer and yellow LEDs in the center, both will fade in together.  After everything has been on for afew seconds then they will fade out in the reverse direction of fade in.  I would appreciate any help or suggestions as to how to tackle this project.  Thank you

Question by pepelpue00   |  last reply


Combinational Lock using shift registers

Last year, i made the circuit of this already but now my brother is asking for my help and i cannot remember it now. im focusing right now in programming and forgot my logic circuit skills..please help me to remember this... what i remembered is that i have shift registers that memorized the buttons (0-9) i pressed...then i enter again a sequence of numbers and the device will check if it corresponds to the numbers i entered...the led will light if it is correct and will not if the numbers entered did not match the default numbers... i still have the list of some materials, 3 universal shift registers, 1 nand ic, 3 xnor ic, 10 toggle switch and 1 hold switch..  its not a very complex circuit..my only problem is to remember on how will i work with the shift registers... please enlighten me once again

Topic by eaon21   |  last reply


3D printed combination lock anyone?

I am in the finnishing stages for a fully 3D printed dial combination lock, similar to what would be used on a safe.Unlike what you might find in other places there is no metal parts.No crappy amount of possible combinations either, 72 per dial dial...I took me a few weeks and quite some filament to get from a draft in Sketchup to something that actually works as planned.As it was more a training excersize in Sketchup for me I had the the following goals:1. Everything is 3D printed with as little afterwork as possible.2. All required springs are 3D printed as well as all other moving or stationary parts.3. Where otherwise fasteners or screws would be required only short leftovers of filament are used to keep the parts in place.Only exception for security reason is the mounts for the front dial and holder.These should be glued or screwed in place if the actual intention is to use it as a working lock.4. The lock shall not be pickable by means of felling, hearing or just trying out random combinations.The above points I got sorted to my satisfaction.However I would like some feedback from trustworth beta testers on the general design and functionality.It is one thing to design something that just works but a bit harder to design it the best possible way.Another big drawback currently is that it seems to be impossible to export proper STL files in Sketchup once they reach a certain complexity.Automatic services or programs to fix these issues result in drastically increased file sizes.Some of the problematic part go from just under 200kb to over 10mb after "fixed".This is not acceptable for me and I have to work on fixing this issue.Most slicers correct these tiny errors automatically and produce a correct print but I prefer proper STL files of small size and complexity over inflated ones that I then need to double check for a long anyways.A few details need changing as my tests showed that you can't drive up print details to a certain level without risking to be unable to mount the parts without further sanding.I hope to have a full set of clean STL files ready for testing by the end of this month.If you are interested to try it out and maybe contribute to an improved version your time will be valued by being mentioned as a beta tester for the upcoming Instructable.Be warned though!This is not for the faint of heart and certainly not for someone who does not know how to calibrate all aspects of the 3D printer involved.The lock also uses quite a bit of filament, currently around 37m all up but I am working on reducing this by replacing solid parts with framework instead where possible.The assembly can be time consuming and frustrating if you realise only once finnished that you have certain parts in the wrong position or orientation.But as said, my goals were not really on making it as easy as possible LOLWhy desing a lock that is neither secure enough nor free of metal parts if there is other options ;)If you happen to work with an Inventor and PLA on the left side then I can provide ready to go .gx files if prefered.They would then be already confirmed to be working and usable on one of my printers.Let me know what you think ...

Topic by Downunder35m   |  last reply


Please check my answer - Combinations problem.

  Hi all, would someone with a maths brain check my reasoning and working here please . . . Imagine a game board with 11 squares and three counters, which can be placed on any unoccupied square.  The counters are equivalent so it matters not which one is where.  There is also a fourth counter which can go anywhere on a square which is not occupied by one of the other counters. How many possible combinations of counter positions are there? OK,  the first part is a 3 from 11 combination problem solved by : n! / (r! (n-r)!) which is 165. For each possible 3 counter combination, the fourth counter can be on any of the remaining 8 spaces, so the total number of possible 'boards' is 8 * 165 = 1320.

Topic by AndyGadget   |  last reply


Combining PSU rails for lab power supply? Answered

I recently received 2 old computers from friends for tinkering purposes. I'd like to take their PSUs and create a power supply for projects. However, they only have max outputs of 110W. So, I have a few questions: 1.) Is it possible to combine rails? 2.) Is it safe? 3.) What kind of power increase would I be seeing? Please try to answer all 3 individually.

Question by General Eggs   |  last reply


Would setting batteries in series combine their mAh? Answered

So say I have four 2,000 mAh batteries, and I set them in series. Would that give me 8,000 mAh?

Question by Sargebubbles26   |  last reply


Combine Old laptop Screen to Broken Monitor

I need help connecting a screen from a broken laptop to a broken screen monitor. please contact me aantonovardakis@gmail.com thanks in regard

Topic by aantonovardakis   |  last reply


Digital Logic Design Project Combinational Lock?

In this project you are required to design a 4 digits combination lock (not using arduino)  The project is such that it can be reconfigurable i.e. there should be an option that we can change the password of the lock at run time. Input to the system is from the hex keypad. Output of the system is ‘open’ and ‘close’ words displayed on a seven segment I used registers,flip flops, mux ,comparator  but couldn't get the desired result

Question by r_sammad   |  last reply


Can I combine 2 computers into one? Answered

I have 2 computers: 256RAM                       256RAM 40Gb hard disk          20Gb hard disk 1.3GHz processor     1.3GHz processor Can I somehow connect the 2 of them into a better one? I know I can take the RAM and the hard disk from one and attach them to the other computer,but I want to connect the 2 processors together . Can I do that?

Question by theVader75   |  last reply


Combine 2 (or 3) Joysticks to make one?

Okay I got 3 old Joysticks and lots of games that would be awesome to use DUAL JOYSTICKS. The joysticks use that old Joystick Port. So my question is if there is a way to join them into ONE set and be able to plug it into my computer. And if possible make it into USB?

Topic by itstemo1 


can stepper motors be combined to double the amps?

I have four stepper motors connected in series to get 12v and more . Can I connect them differently for getting higher amps I think they currently put out like 30 ma each is there a way to increase this amp? thanks for sharing Al

Question by celalboz   |  last reply


can bridge rectifiers be combined to double the amps? Answered

Say we have 3 amp 3 rectifiers soldered would that function as 9amp rectifier or needed to be wired in a special way, series, paralel with other components? I am building an unknown power wind gen ans I gave 10   3 amp rectifiers. Thanks for sharing.. Al

Question by celalboz   |  last reply


How to use batteries in a Series-Parallel Combination?

   Is it possible to use 4 AAA Duracell batteries instead of 2 AA batteries if I were to put it in some form of Series/Parallel combination? Would it keep the same voltage and stuff to not interfere with the electronics of something but just increase the time between changing batteries? What would the layout look like for this? Thanks Instructablers!

Question by ranaakamarth   |  last reply


K'nex combined with LED's to create awsome Orbs.

I think this is a great example of the neverending potential of knex.This photographer set about making rotating led lit orbs. He then used a long exposure on his camera to create the amazing pictures you see here.I think for a simple building method, for a non permanent project, knex is one of the best options, and greatly under appreciated!Check out his full Flickr Set.via Makezine

Topic by gmjhowe   |  last reply


Push button controlling different light combinations?

You know how with some flash lights and such, you click the button and one LED turns on, then you press it again and more turn on. How would I get a result similar to that? What I'm trying to do is pressing a N/O button once and LED 1 turns on then clicking it again and LED 1 turns off while LED 2 turns on. I've been scratching my head over it for a few days but I cant figure out how.

Question by Kruegem   |  last reply


how to combine 2 Arduino codes together ?

Hello, I have a question. I need to combine my code for my Arduino project. I'm using a Arduino micro board .  The 2 codes are maxsonar and another is a flying drones coding. I'm lost and don't know how to combine the both of them as the maxsonar code will overwrite the flying drones code causing it unable to fly. Maxsonar code const int anPin1 = 0; const int anPin2 = 1; int triggerPin1 = 13; long distance1, distance2, cm1 ,cm2; void setup() {   Serial.begin(9600);  // sets the serial port to 9600   pinMode(triggerPin1, OUTPUT);   pinMode(A5, OUTPUT);   pinMode(A11, OUTPUT); } void start_sensor(){   digitalWrite(triggerPin1,HIGH);   delay(1);   digitalWrite(triggerPin1,LOW); } void Fading()//led1 { if (distance1 == 9) {    analogWrite(A5,25.5);     delay(10); } else if (distance1 == 8) {    analogWrite(A5,76.5);     delay(10); } else if( distance1 == 7) {    analogWrite(A5,153);     delay(10); } else if(distance1 == 6) {    analogWrite(A5,255);     delay(10); }   }   void Fading2()//led1 {   if (distance2 == 9) {    analogWrite(A11,25.5);     delay(10); } else if (distance2 == 8) {    analogWrite(A11,76.5);     delay(10); } else if( distance2 == 7) {    analogWrite(A11,153);     delay(10); } else if(distance2 == 6 ) {    analogWrite(A11,255);     delay(10); }   }   void read_sensors(){   /*   Scale factor is (Vcc/512) per inch. A 5V supply yields ~9.8mV/in   Arduino analog pin goes from 0 to 1024, so the value has to be divided by 2 to get the actual inches   */   distance1 = analogRead(anPin1)/2;   distance2 = analogRead(anPin2)/2; } void count_in_cm() {   cm1 = distance1 * 2.54;   cm2 = distance2 * 2.54; } void print_all() {     if( distance1 <10 && distance2 >=10 )   {   Fading();   analogWrite(A11,0);   Serial.print("Sensor1: Warning");   Serial.print(" ");   Serial.print(" ");   Serial.print("S2");   Serial.print(" ");   Serial.print(distance2);                                                                                                                                                                                                                                                                                                              Serial.print("in");   Serial.print(" ");   Serial.print(" ");   Serial.print(cm2);   Serial.print("cm");   Serial.println();   delay(700);     }   else if(distance1 >= 10 && distance2 < 10)   {   Fading2();   analogWrite(A5,0);   Serial.print("S1");   Serial.print(" ");   Serial.print(distance1);   Serial.print("in");   Serial.print(" ");   Serial.print(" ");   Serial.print(cm1);   Serial.print("cm");   Serial.print(" ");   Serial.print(" ");   Serial.print("Sensor2: Warning");   Serial.println();   delay(700);   }   else if (distance1 < 10 && distance2 < 10)   {     Fading();     Fading2();     Serial.print("Sensor1: Warning");     Serial.print("  ");     Serial.print("Sensor2: Warning");     Serial.println();     delay(700);      }   else   {   analogWrite(A11,0);   analogWrite(A5,0);   Serial.print("S1");   Serial.print(" ");   Serial.print(distance1);   Serial.print("in");   Serial.print(" ");   Serial.print(" ");   Serial.print(cm1);   Serial.print("cm");   Serial.print(" ");   Serial.print(" ");    Serial.print("S2");   Serial.print(" ");   Serial.print(distance2);   Serial.print("in");   Serial.print(" ");   Serial.print(" ");   Serial.print(cm2);   Serial.print("cm");   Serial.println();   delay(700);   } } void loop() {   start_sensor();   read_sensors();   count_in_cm();   print_all();   delay(200); //This is the equivant of the amount of sensors times 50.  If you changed this to 5 sensors the delay would be 250. } flying drone code #include #include // channel declaration Servo channel1; // throttle Servo channel2; // yaw Servo channel3; // pitch Servo channel4; // roll Servo channel5; // ball drop servo // PWM freq setting, should it be 62.33Hz? const int PWMConst = 20022;//50HZ // global variables byte incomingByte, incomingByteUSB; byte rcBuffer[32], usbBuffer[12]; int i = 0, j = 0, STATE = 1; int Flag = 0, usbFlag = 0; unsigned int thr_16int = 0, yaw_16int = 0, pit_16int = 0, rol_16int = 0, gear_16int = 0; unsigned int thr_16int_usb = 0, yaw_16int_usb = 0, pit_16int_usb = 0, rol_16int_usb = 0; float throttle = 1000, roll = 1500, pitch = 1500, yaw = 1500; int gear = 1500; float currT, prevT = 0, _flagHover, throFlag; // functions declaration void extract_RC_cmd(void); void extract_USB_cmd(void); void translate_RC_cmd(void); void translate_USB_cmd(void); void RC_Neutral(void); void reset_usb(void); void reset_rc(void); void hover(void); void sonar(void); void setup() {   // setting registers   TCCR1A = _BV(COM1A1) | _BV(COM1B1);   TCCR1B = _BV(WGM13) | _BV(CS11);   ICR1 = PWMConst;   // set PWM I/O ports   channel1.attach(6);    // throttle   channel2.attach(9);    // yaw   channel3.attach(5);    // pitch   channel4.attach(10);    // roll   channel5.attach(11);   // fail safe-attit   //init usb buffer   usbBuffer[0] = 0x03;   usbBuffer[1] = 0xE8;   usbBuffer[2] = 0x0D;   usbBuffer[3] = 0xAC;   usbBuffer[4] = 0x15;   usbBuffer[5] = 0x7C;   usbBuffer[6] = 0x1D;   usbBuffer[7] = 0x4C;   reset_rc();   reset_usb();   Serial1.begin(115200);   // rc Rx data in   Serial.begin(115200);     // USB } void loop() {   // accept serial data from computer   if (Serial.available() > 0)   {     incomingByteUSB = Serial.read();     if (incomingByteUSB >= 0x03 && incomingByteUSB <= 0x07)     {       usbFlag = 1;     }     if (usbFlag == 1)     {       usbBuffer[j] = incomingByteUSB;       j++;       if (j == 12)       {         usbFlag = 0;         j = 0;         extract_USB_cmd();       }     }   }   // accepte serial data from RC   if (Serial1.available() > 0)   {     incomingByte = Serial1.read();     if (incomingByte >= 0x80 && incomingByte <= 0x87)     {       Flag = 1;     }     if (Flag == 1)     {       rcBuffer[i] = incomingByte;       i++;       if (i == 32)       {         Flag = 0;         i = 0;         extract_RC_cmd();       }     }     // Serial.print(rcBuffer[i]);   }   // STATE MACHINE   switch (STATE)   {     case 1:       translate_USB_cmd();       reset_rc();       //Serial.print();       break;     case 2:       translate_RC_cmd();       reset_usb();       //Serial.print('R');       break;     case 3:       landing();       break;     default:       RC_Neutral();       break;   }     // output PWM   channel1.write(throttle);   channel2.write(yaw);   channel3.write(pitch);   channel4.write(roll);   channel5.write(gear); } // local functions void extract_RC_cmd() {   if (rcBuffer[0] >= 0x80 && rcBuffer[0] <= 0x87) // double check throttle range   {     thr_16int = rcBuffer[0] << 8 | rcBuffer[1]; // 16 bit throttle     // Serial.print(thr_16int);   }   if (rcBuffer[4] >= 0x19 && rcBuffer[4] <= 0x1E) // double check yaw range   {     yaw_16int = rcBuffer[4] << 8 | rcBuffer[5]; // 16 bit yaw     //Serial.print(yaw_16int);   }   if (rcBuffer[16] >= 0x09 && rcBuffer[16] <= 0x0E) // double check yaw range   {     rol_16int = rcBuffer[16] << 8 | rcBuffer[17]; // 16 bit yaw     //Serial.print(rol_16int);   }   if (rcBuffer[20] >= 0x11 && rcBuffer[20] <= 0x16) // double check yaw range   {     pit_16int = rcBuffer[20] << 8 | rcBuffer[21]; // 16 bit yaw     //Serial.print(pit_16int);   }   if (rcBuffer[22] >= 0x21 && rcBuffer[22] <= 0x26) // double check gear range   {     gear_16int = rcBuffer[22] << 8 | rcBuffer[23]; // 16 bit pitch     //Serial.print(pit_16int);   }   // state   if (rcBuffer[24] == 0x37 && rcBuffer[25] == 0xE0)    // Fmode SW state 1: Auto   {     STATE = 1;   }   else if (rcBuffer[24] == 0x34 && rcBuffer[25] == 0x00) // Fmode SW state 2: Manual   {     STATE = 2;   }   else if (rcBuffer[24] == 0x31 && rcBuffer[25] == 0xB4) // Fmode SW state 3: Emergency landing   {     STATE = 3;   } } void extract_USB_cmd(void) {   if (usbBuffer[0] >= 0x03 && usbBuffer[0] <= 0x07) // double check throttle range   {     thr_16int_usb = usbBuffer[0] << 8 | usbBuffer[1]; // 16 bit throttle   }   if (usbBuffer[2] >= 0x0B && usbBuffer[2] <= 0x0F) // double check yaw range   {     yaw_16int_usb = usbBuffer[2] << 8 | usbBuffer[3]; // 16 bit yaw   }   if (usbBuffer[4] >= 0x13 && usbBuffer[4] <= 0x17) // double check pit range   {     pit_16int_usb = usbBuffer[4] << 8 | usbBuffer[5]; // 16 bit pitch   }   if (usbBuffer[6] >= 0x1B && usbBuffer[6] <= 0x1F) // double check rol range   {     rol_16int_usb = usbBuffer[6] << 8 | usbBuffer[7]; // 16 bit role   }   // state   if (usbBuffer[10] == 0x2A && usbBuffer[11] == 0xF8)   {     //state = 1; // auto   }   else if (usbBuffer[10] == 0x2C && usbBuffer[11] == 0xEC)   {     STATE = 3; // emergency landing   }   else if (usbBuffer[10] == 0x2E && usbBuffer[11] == 0xE0)   {     STATE = 0; // default rc neutral   } } void translate_RC_cmd(void) {   throttle = (thr_16int - 30752 ) / 2.016;   yaw   = (9243 - yaw_16int) / 1.382;   pitch = (pit_16int - 3047) / 1.378;   roll  = (5129 - rol_16int) / 1.373;   gear  = (gear_16int - 7506) / 1.165;   throttle = min(2000, max(1000, throttle));   yaw      = min(2000, max(1000, yaw));   pitch    = min(2000, max(1000, pitch));   roll     = min(2000, max(1000, roll));   gear     = min(2000, max(1000, gear)); } void translate_USB_cmd(void) {   throttle = thr_16int_usb;   yaw = yaw_16int_usb - 2000;   pitch = pit_16int_usb - 4000;   roll =  rol_16int_usb - 6000;   //Serial.print(thr_16int_usb);   throttle = min(2000, max(1000, throttle));   yaw      = min(2000, max(1000, yaw));   pitch    = min(2000, max(1000, pitch));   roll     = min(2000, max(1000, roll)); } void RC_Neutral(void) {   throttle = 1000;   yaw = 1500;   pitch = 1500;   roll = 1500; } void landing(void) {   throttle = throttle - 1;   if (throttle <= 1000) throttle = 1000;   yaw = 1500;   pitch = 1500;   roll = 1500; } void reset_usb(void) {   thr_16int_usb = 1000;   yaw_16int_usb = 3500;   pit_16int_usb = 5500;   rol_16int_usb = 7500; } void reset_rc(void) {   thr_16int = 0x8000;   yaw_16int = 0x1C03;   pit_16int = 0x13FD;   rol_16int = 0x0C07; }

Topic by singno123   |  last reply



how do you make a laser beam combiner?

Im trying to combine a red and green to make yellow

Question by Jake Morton   |  last reply


Grouting combination sheets of glass and marble tile on backsplash. Answered

My 12" sheets of marble and glass tiles (combined on same sheet) have marble tiles that are thicker than the glass in many spots making the finished surface uneven. How would I grout this uneven surface?

Question by loree.kaye   |  last reply


How to combine two 5v transformes to get 10v+?

Any way or solution DIY to conbine two transformes 5v?

Question by MarcosM117   |  last reply


Sci-Fi Critters - Insects combined with Watch Parts

Insect Lab combines real insect specimens with antique watch parts and other technological components to create these sci-fi critters.  Jason showed me these and I thought they were beautiful!  The beetles and butterflies are my favorite.

Topic by Carleyy   |  last reply


Cathode Ray Tube and Cloud Chamber Combined - Possible?

Is it possible to build a cathode ray tube and observe the path of electrons in a combined (or linked) cloud chamber? I would want to apply a uniform magnetic field to the cloud chamber but not the CRT so that electrons travel in a straight line into the chamber and are subsequently deflected. Oh, and ideally using materials that were available in 1917! Thanks in advance.

Topic by boroman   |  last reply


Can I combine a Wacom tablet with a samsung tablet?

I have a wacom drawing pad and I was wondering if its possible to hook it up to a regular samsung galaxy tab 2 somehow.

Question by monsterlego   |  last reply


How do I combine multiple audio signals? Answered

I'm trying to splice in the output from an mp3 player into the microphone of Xbox headset. I've had no luck simply inserting it into the circuit, is there something else involved? Sincerely, Bean

Question by meanbean   |  last reply


Xbox battery charger and plug and play: combine the two? Answered

I'm looking to wire up a plug and play cord to a xbox battery charging station so the cord used to power the station would essentially charge two batteries and a controller. I've never dealt with USB charging, so any and all help would be great. Thanks in advance!

Question by DoctorWoo   |  last reply


Connecting/combining left and right audio channels together? Answered

Hi, I have something that can only take one channel but I am wondering if I can just connect the red and blue wires together in a audio cable so it will combine these both left and right channels into a single mono source (from the amplifiers point of view). Will this cause any problems with the audio source (phone) having both channels connected together like this? Will it damage the phone or anything like that? The main reason for doing this is the source (the phone) is stereo and some songs will have parts that are only present on one channel, which means that if it is not on the channel that is connected to my homemade lm386 based amplifier you wont here that part. Thanks.

Question by Alex1M6   |  last reply


How to combine 2 audio signals from HDMI

As I've known so far there aren't receivers that mix audio.I want to mix 2 HDMI sources, lets say 1 is a PS4 and second is Xbox One, how would I mix them in 7.1? Mix the 2 audio sources into 1, is there a way of doing that? What is the simplest way.I know that there are stereo mixers, but haven't heard of a HDMI one.What is the simplest way of mixing both signals?I think it might have something to do with modulating the signals, but I dont specifically know how modulators work.

Topic by MatanY2   |  last reply


Standby mode for an ASK RF transmitter and HT12E combination? Answered

Hey,     I am working on a project that uses the HT12E encoder to encode binary codes and an ASK RF transmitter that transmits the data at 433 MHz.It will be received by their respective counterparts i.e,HT12D and ASK RF receiver.The range is about 25 metres.The transmitter is at the roof of my house while the receiver is on the ground floor(The circuit is for detecting the water level in a tank). The transmitter is not required to transmit 24/7 but only when the receiver is switched ON.It can be achieved by making the transmission enabling pin of the encoder ic high when transmission is not needed but for that I would either have to go to the roof and turn the transmitter ON(which beats the purpose) or I'll need another transmitter-receiver pair which would occupy positions opposite to the pair that already exists.(It would essentially be a transceiver then). But I don't want another pair of transmitter-receiver and neither do I want the transmitter to transmit continuously . What I need is a solution to install a standby mode for the transmitter and are there any ways to do that keeping in mind the above requirements? Any help will be appreciated and thank you for reading my question.

Question by Adarsh_tronix   |  last reply




How do I build the combination part of a lego safe? Answered

My friend and I are building combination safes out of lego and he doesn't know how to make the combination device, Do any of you have suggestions? If you know a url of a youtube video that demonstrates the combination device well please post a link in the answers. 

Question by venom1539   |  last reply


does anyone know any program that will combine mp4s well? Answered

 I want to be able to watch a full episode of Karin (Chibi Vampire) and I can download the video in 3 different parts. Now does anyone know of a program that will take each video and combine them into one?

Question by Iridium7   |  last reply


Combine two usb solar panels for higher wattage output

So, just thinking about this.  I have an anker 14w foldable solar panel.  I like it, but it seems to not quite have the wattage output that I would prefer.  What if I were to make cable that would join these two usb output sources into one.  Same voltage of course, just higher wattage potential. Again, just an idea.  Thoughts?

Topic by n5yzv   |  last reply


Smart Digital Clock combined with Raspberry Pi and Google Assistant

I want to make a smart digital clock using Raspberry Pi and Google assistant. I also want it to display the temperature and also to have a regular alarm in it if there is no wifi connection. I am wondering what parts do I need to be able to make this and what do I need to make Google assistant connect other accounts like spotify or anything else?

Question by HibiC   |  last reply


How can i combine these two instructables for halloween prop?

I am making a haunted house, and want my pneumatic props to be triggered once the laser beam is broken. I have followed the instuctable for a laser tripwire  https://www.instructables.com/id/Another-Arduino-Laser-Tripwire/ and the instructable for a 110v controller  https://www.instructables.com/id/Yet-Another-Arduino-110v-Power-Controller/ both work great seperately, however what i would like to do is have 4 lasers, and each one controls one of the 4 outlets. can anyone help me in code and schematic? i would greatly appreciate it. Sam

Question by Zukibeast   |  last reply