Search for dc motor stepper in Topics


DC motors & stepper motors

I have 13 stepper motors and 10 dc motors for sell. I just have way too many laying around. I would like to sell them all for 40 dollars shipped using paypal. I'm hopping to sell them to help fund my CNC project. I also might be adding more motor as I find them.

Topic by r1dd1ck913    |  last reply


Stepper Motor as a 'normal' motor

Hi, I recntly took apart a hard drive and there is a 7200 rpm motor inside. Only problem is that it is a stepper motor and I don't have any equipment to drive stepper motors and buying stuff to do is err... cost prohobititve.  Would connecting a negitive wire to 2 of the terminals and positive(in sort of a crisscross pattern e.g. -+-+) to the other make it run like a regular motor? I just don't want to invest time  to solder it only to have it not work.

Topic by ChickBang    |  last reply


Stepper motor

I have a small size sanyo denki 103 series stepper motor. I wanted to use it using L298 driver. What will be the connections  

Question by UsmanR1    |  last reply


Stepper Motors..

I recently pulled two stepper motors out of a working IBM dot-matrix printer. One larger, 3v one with 1.8 steps. The other is a smaller, 9.5v one with 7.8 steps. I am more interested in the large one right now. I managed to find out that the large one has center-tapped coils. I also found out that Coil 1 is red-white-brown, coil 2 is blue-black-yellow. I found the schematic below on http://ashishrd.blogspot.com/2007/09/computer-controlled-stepper-motor.htmlI was wondering how this could be adapted to control my motor from a PC program with the ULN2003 (that chip sounds like UT2003)? Here are the complete residences of what I found on the wires with a multimeter, in case that helps. Resistances:Red to Brown: 8 ohms (or 7 some times)Red to White: 4 ohmsWhite to Brown: 4Blue to Yellow: 7Yellow to Black: 4Black to Blue: 4

Topic by l0cke    |  last reply


stepper motor

Wondering if any one knows how to control stepper motors via Hand wheels. By rotating the wheel you should be able to control the rotation of the wheel either clock wise or ccw. I do not want to interface the motor through a computer.

Topic by rajivraj    |  last reply


Stepper motor driver?

Hi! I am trying to find a good h-bridge for a 3 volt stepper motor. Basically my plan is to build a stepper motor controller with an arduino for controlling various functions in a model kit. I have the arduino-kit and the motors. But I need a good reference for a h-bridge, but all i can find are chips rated for much larger drive currents. Also exactly how hot does a hbridge get when under load? I would like to integrate the bridges into the kit, but since it is plastic, I would like to know in advance how hot it gets, and if it gets too hot I'll have to look at another solution.Any help appreciated! PS. If you can please put the hbridge part ID in your answer for easy reference. DS.

Question by feldreich    |  last reply


DC motor

I had a 220v angle grinder. It was burnt. I take the rotor of the grinder out. Its completely fine. Now i make a DC motor using this rotor and magnets(for field current). My question is, how much maximum DC volts this motor can take to get the maximum RPM. Because the motor was 220v AC, Will it run on 220v DC?

Question by Shezi007    |  last reply


dc motors

Hi: Can anyone tell me why my 24volt dc motor which I just got rebuilt will only work on 12 volts and immediatly overheats and stops with 24 volts? Thanks, Royal

Topic by cra    |  last reply


DC Motor

Hi Guys, I have a 15.6 volt dc motor taken out of a handheld vacuum cleaner. is this suitable to use in a small wind generator as a project with my kids. when i attach it to a power drill and spin it from the shaft i dont seem to get any power generation. If i connect it to a 12v battery is spins real fast. any help would be appreciated sam

Question by sam301    |  last reply


Motors

I'am making a car that should carry 50 kg and move at a speed of 10 km/hr. Can anyone help me in choosing the right DC motor??

Topic by Masked_r    |  last reply


What Stepper Motor Is This, IF it is a stepper??????????

Hi I am a starting level, I mean mail room like even, electronics enthusist, and have been working on a project to make a wifi transmitted dc motor video camrea, with pan/tilt, zoom focus, IR All controled and veiwed through a wifi network and on a pc. I have almost all the parts and set up is going great with the addition of a Lens I salvaged from an 1984 video camrea, ya know the ones you had to hook up to your vcr just to get it to work. Well It was a simple two motor set up with a high quitly lens. As I yanked the lens configuration, ever so gently, the horrer poured forth from my face as I realized that even though one of the motors had 2 wires from it, the secound had 4. I have no ideal about motor orvoltage identification. I am so worryed about hooking up any old power sorce and hoping for the best. I really wanna use this lens but don't wanna fry the motors. COuld any one help me out?? I have included a PDF. of the circuit lay out of the camrea itself my GF was so gifted to find and a couple of pictures of the actual motors and wire set up. If any one could tell me what I am working with and what voltage input I need it would be duely welcomed. And if possable would anyone be able to tell me for the smaller 2 led motor as well?? It's got 2334H printed on it and is from the Nihon Mini Motor INC. Thank you......

Topic by pumpkinhead    |  last reply


controll a stepper motor

Can you controll a stepper motor with push switches no circuit? i need a 12v motor with pllanty of speed  torque for a diy cnc but i want to controll it manualy with a joystick made with push switched can i just apply power to a stepper motor like a hobby 12v dc motor and run it without a circuit?

Question by skullkeeper80    |  last reply


alternative stepper motors?

I recently tore into a couple printer-scanners looking for stepper motors. Unfortunately all I found were some DC motors that seem to be tied into some sort of sensor that acts like a step counter. Does anyone know what they are called and how to use them in place of stepper motors for a CNC machine? As a side note, I have a very limited understanding of IC function, think of me as having lived a purely analog lifestyle.

Topic by 50ul84n3    |  last reply


Motors, time and boredom

I have been collecting motors for a while now, and have no idea what to do with them. They range from 5-12VDC, brushed, brushless, stepper, etc. Any potential ideas for projects would be appreciated.  Thanks!

Topic by dansassin    |  last reply


Arduino + Stepper

Hi! I have an Arduino nano and a Minebea PM55L stepper motor and I have to connect these two together. I read the Arduino tutorials, and got a ULN2003 chip. The thing I am unsure of is the power supply and which wires of the motor do what or should be connected to what. There's 6 of them and I really don't want to fry anything if at all possible. Could somebody help out, please?

Topic by TashaDax    |  last reply


Stepper motor help? Answered

Someone tell me how to https://www.youtube.com/watch?v=WQKsll_qeMM only for 90 degree both sides

Question by basim.moulana    |  last reply


stepper motor help

Hi, i need help in building a cnc machine. not the hardeware just the circuit. i already saw this https://www.instructables.com/id/EG9RXG6F54HJ7SL/ and the circuit that it included but i coulden't understand the circuit. there is this circuit http://www.aaroncake.net/circuits/stepper.asp which i have already built but need help connecting it to my parallel port on my computer. i would really appreciate it.

Topic by dark_inuyasha    |  last reply


disc stepper motor

Ok im new to the tech world but i have a an idea haven to do with a stepper motor that is in disc form and capable of being programmed but i dont know what parts i would need and how to go about it any insight or possibly a parts list to do it? please and thank you

Topic by mobilesuit990  


Android Stepper Motor?

So I am working on controlong shades in my house with my android phone and my arduino over bluetooth. i was thinking on using a steper motor to act as a gear to open and close the blinds. could anyone help me with any toturials or a link to any documentation involving bluetooth stepper control? Plese help.

Question by broskiz    |  last reply


Astrosyn Stepper Motors

I have 2 Astrosyn Stepper Motors that I bought and ended up not using. I was going to build a small cnc machine first but decided to go bigger with the first on I built. So i bought bigger steppers for my application. I bought them for 20 bucks each and now I am selling them for 20 bucks plus shipping for both. I would like to use paypal for any transactions. Thanks for looking.

Topic by r1dd1ck913    |  last reply


Stepper Motor Music!

Some guy used steppers to play tones and music using an arduino :DSource And a few others

Topic by ReCreate    |  last reply


Precision Stepper motor????

Is there a precision stepper motor and programming hardware that i could program to go to a certain 1/50 of a turn. I would use it for a locker lock unlocker, 3 digit combo lock. What are my best options for cheap?? Thank you

Question by theboygenius    |  last reply


Stepper motors for sale

I have a few large stepper motors I pulled out of a liquid sinilation counter. I'm not exactly sure what thier value is, similair motors are priced around 50-60$ new, so offers are welcome. They operate ~6v and have 0.90 degree steps, I believe they are bipolar. I can upload pics if needed.

Topic by martzsam    |  last reply


Stepper motor controllers

Does anyone know where I can buy some bipolar stepper motor controllers and an H-bridge in one package? Or even better, schematics/pcb layout of a driver board?UPDATE:Does anybody have any experience with the Easy Driver? It seems like a cheap alternatives to some of the other available controllers, but I just want to know if you get what you pay for.

Topic by ongissim    |  last reply


stepper motor question

Ok, i am trying to make a chain clock, its just a clock with a gear instead of a minute hand that turns a chain with 12 numbers on it. my problem  is; the chain i am using is too heavy for a conventional quarts movement. i would like to use a stepper motor but all the drive circuits i find need an arduino. are there any simple circuits i can make, to use a stepper motor for a clock? i do have some circuitry skills so i can work around some stuff. thanks for the help :)

Topic by golddigger1559    |  last reply


CNC stepper motor Answered

Hello, I would like to use my 3 printer scanners I recently salvaged for a CNC. Would you expect the motors to be able to cut aluminum with a multi-speed dremel? If there is enough torque, it would be sufficient to make a 3d printer right?

Question by jbaker22    |  last reply


Stepper Motor Library

Hi! Sorry, I was unable to put library below. So simple and yet so not so simple. How do I get the library in the folder so the program compiles/? Thanks 56Frank library for 28BYJ48 Stepper motor and ULN2003 driver. Here is the source code for our 28BYJ48 stepper motor, ULN2003 driver library, as well as an implementation. Check out the diagram for the wiring. The header file: __________________________________________________________________ #ifndef Stepper_h #define Stepper_h class StepperMotor { public:     StepperMotor(int In1, int In2, int In3, int In4);    // Constructor that will set the inputs     void setStepDuration(int duration);    // Function used to set the step duration in ms     void step(int noOfSteps);    //    for(int sequenceNum = 0;  sequenceNum <= noOfSteps/8; sequenceNum++){         for(int position = 0; ( position < 8 ) && ( position < ( noOfSteps - sequenceNum*8 )); position++){             delay(duration);             for(int inputCount = 0; inputCount < 4; inputCount++){                 digitalWrite(this->inputPins[inputCount], sequence[(int)(3.5 - (3.5*factor) + (factor*position))][inputCount]);             } Arduino         }     } } _______________________________________________________________________ An implementation: _______________________________________________________________________ #include StepperMotor motor(8,9,10,11); void setup(){   Serial.begin(9600);   motor.setStepDuration(1); } void loop(){   motor.step(1000);   delay(2000);   motor.step(-1000);   delay(2000); } Step a certain number of steps. + for one way and - for the other     int duration;    // Step duration in ms     int inputPins[4];    // The input pin numbers }; #endif ___________________________________________________________________ The cpp file: ___________________________________________________________________ #include #include StepperMotor::StepperMotor(int In1, int In2, int In3, int In4){     // Record pin numbers in the inputPins array     this->inputPins[0] = In1;     this->inputPins[1] = In2;     this->inputPins[2] = In3;     this->inputPins[3] = In4;     // Iterate through the inputPins array, setting each one to output mode     for(int inputCount = 0; inputCount < 4; inputCount++){         pinMode(this->inputPins[inputCount], OUTPUT);     }     duration = 50; } void StepperMotor::setStepDuration(int duration){     this->duration = duration; } void StepperMotor::step(int noOfSteps){     /*         The following 2D array represents the sequence that must be         used to acheive rotation. The rows correspond to each step, and         the columns correspond to each input. L     */     bool sequence[][4] = {{LOW, LOW, LOW, HIGH },                           {LOW, LOW, HIGH, HIGH},                           {LOW, LOW, HIGH, LOW },                           {LOW, HIGH, HIGH, LOW},                           {LOW, HIGH, LOW, LOW },                           {HIGH, HIGH, LOW, LOW},                           {HIGH, LOW, LOW, LOW },                           {HIGH, LOW, LOW, HIGH}};                           int factor = abs(noOfSteps) / noOfSteps;    // If noOfSteps is +, factor = 1. If noOfSteps is -, factor = -1     noOfSteps = abs(noOfSteps);    // If noOfSteps was in fact negative, make positive for future operations     /*         The following algorithm runs through the sequence the specified number         of times     */

Topic by 56Frank    |  last reply


DC motor regulation

I am planning to build a small gearbox that depends on a steady rpm from a 3V dc motor. I understand that the output rpms will change in correlation to the fluctuation of input power. My question is, if I used a regulator to regulate the input voltage from 5V to 3V, will that keep the motor rpms steady?

Topic by Tman179    |  last reply


DC MOTOR CONTROLLER

RELATED TO DC MOTOR CONTROLLER (EV VEHICLES) 1: Need for large number of capacitors in the power circuit (store the charge and dissipate to which part of the component mosfet or diodes ??) ? 2: what are diodes parallel to the mosfets for ? ( other than preventing the back emf coming from the motor ) and is it have anything to do with firing angle ? 3:advantage of using many mosfets in parallel than using a single mosfet and on what basis must that mosfet chosen? I am from India a college student pursuing my electronics engineering and making motor controller,i am able to get all the circuit details and how the motor controller works but i have above few doubts

Topic by doraditya    |  last reply


Large DC motor

I'm looking for a relatively cheap motor that would be large enough to spin around a nerf Vulcan. I don't know much about what kinds of motors would be good, or where I could get them. From what I've found, they're not that common and they're super expensive. Does anyone know where I could get one for under 100 dollars? It doesn't need to be fast. Thank you in advance for your help.

Topic by alecnotalex    |  last reply


Can a 24V AC stepper motor be run from 12V DC ?

Hi Instructables people,  have been searching for days to find if there any way of running 24V AC bipolar steppe motor from a 12V DC battery without using a DC to AC inverter. Not used stepper motors before so any advice would be greatly appreciated. 

Question by alscotia    |  last reply


WANTED: DC motor

I'm trying to build a wind turbine. If anybody has a DC motor from a old treadmill, electric scooter, etc. I would love to have it. The idea motor would be one with highest volts per rpm. That means low rpms and high volts. Let me know if you have something.

Topic by JSTArollin  


DC Motor Problem?

Hi , to whoever is reading this .I wired 2  3v dc toy motors in series and I used about 4.5v as the power source. As I powered it up one motor spun fast and the other spun slower , so I thought the one running slower was defective an so I bought another motor and wired it in series with the  that was spinning fast and thought their speeds would be equalled, however the new one I bought started running faster and the old I one I had that spun faster began spinning slower than the new one. I tried the new one with the old one that had been spinning slower and arrived at the same result.. Could this be because I wired the motors in series ? I  Really need help s o please help me and thank you in advance and for taking the time the read this.

Question by Strontium    |  last reply


PIR DC Motor? Answered

Hi all, I am trying to set up a dc motor controlled by a PIR sensor using an arduino.  When the PIR sensor is triggered, I would like the motor to turn on for half a second and then off.  However, no matter what "delay" I write into the sketch, the motor always stays on for around four seconds.  Could someone please help me? The sketch I have written is below and have provided a picture of my set-up: const int pirPower = 12; const int pirIn = 13; int motorPin1 = 3; void setup(){ pinMode(pirPower, OUTPUT); pinMode(pirIn, INPUT); pinMode(motorPin1, OUTPUT); digitalWrite(motorPin1, LOW); digitalWrite(pirPower, HIGH); } void loop(){   int value= digitalRead(pirIn);     if (value == HIGH){       digitalWrite(motorPin1, HIGH);       delay(2000); //will not start if = 0-20.  The signal is stronger the higher the delay goes.  Time active remains the same.       digitalWrite(motorPin1, LOW);     } }

Question by Josh_Lucas    |  last reply


VCR Loading motor voltage?

Hi everyone, I recently dismantled an old VCR and found a DC motor, I apparently got no manufacture label just a label with two rows of numbers and these numbers are: 4-570V-02700 B60730 051* I initially thought that the 570V was the voltage of the motor but i'm not sure about it. i googled the first row of numbers and found that it's probably a Sanyo 4-527V-02700 Loading Motor Dc 5.2W, but I can't find anymore specifications for it.

Question by matokage    |  last reply


Normal motors working as a stepper motor?

Hey folks, I have an arduino(Also l293d motor control) and I was wondering if I could use my normal motor just like a stepper motor by creating a funtion and using "delay" as a mode to control the rpm of the motor

Question by cthaliyath    |  last reply


Motor Controller

Dear Sir, Can you help me in developing a 24/36 mosfet controller for tricycle? Regards P​

Topic by hgsan    |  last reply


Use brushless DC motor (or stepper motor) as RPM sensor?

Hi all, I'm making an Arduino based digital instrument cluster for my 1980 XS400 motorcycle. all the old tach and speedo instruments are mechanical so I need to convert the spinning cable's rotation to digital RPM. I've tried IR tachs but I can't seem to get them to be accurate enough (the lowest RPM I could get out of them was about 375, which isn't low enough) I'd love to use a more mechanical means of getting the RPM. could I use a 3 phase DC motor to count RPM? if I can, how?

Question by AedanGraves    |  last reply


Can i use Stepper motor Stepper Motor 42BYGH4417 in uln2003 ???

Can i use Stepper motor Stepper Motor 42BYGH4417 in uln2003 ??? Please answer, i need help :(  sorry im newbie 

Question by dannisa    |  last reply


can i speed control a dc motor with a nitro cars stepper motor?

Hello, i ant to know if i can use the stepper system from a r/c nitro car to control the speed of two motors individually (with two different steppers though), using this electronic speed controller kit http://jaycar.com.au/productView.asp?ID=KC5225&keywords;=speed+controller&form;=KEYWORD i plan on using two of these to control the speeds of the left and right motor for my remote controll tank, which uses brushed motors

Question by oldmanbeefjerky    |  last reply


Do stepper motors produce to sets of electricity? 2 positive and 2 negitive? Answered

 I made a bike generator. Now I am adding a stepper motor to it. I see that in 2 instructables people used them with two ac-dc bridges. 

Question by TOCO    |  last reply


If I have 3 DC 4V 1.1A Stepper motors and a TB6560 Driver, how much power do I need?

If I have 3 DC 4V 1.1A Stepper motors and a TB6560 Driver, how much power do I need? The driver motor say it need 12v for the fan. I dont want to fry out the only free motors I got.

Question by Uggswhiteguy  


Stepper motor, driver, microcontroller

I am looking for someone to help me with with a stepper motor. (ofcourse you get paid) I would like to have a small stepper motor something like this(the main thing is that it isnt bigger then WxHxD 50mmX60mmx15mm) . http://dativoweb.net/sites/default/files/u33/ItaliaImballaggio/5_14_delta_line_motore.jpg I would like a driver and a microcontroller to this almost in the same size, would love to have this thiner thou. I would like to have this programmed, like the stepper to do 1 revolution in 180 minutes (1 full rotation in 3 hours) if it possible to get it running on batteries it be great! Folow the link to a image i made to se how i like it to be. http://lajkade.se/stepper.png Is this possible? And is it someone who got the knowledge to do this? Awaiting your answere! Best regards Jacob

Topic by soderhjelm    |  last reply


How do I control DC &amp; Stepper motors using my PC?

I need to control 4 DC motors (no speed control, only direction) and 1 stepper motor (again no speed control, only direction) for an engineering project of mine using a PC. I am not sure if I should use the serial or the parallel port. Also, I'm comfortable using VB. So it would be helpful if someone could help me with the interfacing circuits and the code or atleast point me to some resources! Please help!

Question by exchequer598    |  last reply


Uni-polor Stepper Motors

OK so now I have some Unipolor stepper motors for sell. 20 bucks plus shipping takes all 3. Thanks for looking.

Topic by r1dd1ck913    |  last reply


Universal stepper motor controller

I wanted to create a universal stepper driver that is capable of driving a stepper of 250w rating at 20A current and a load voltage of 12V . Does anybody have an idea of how to go about it ? . Please do guide me if you have any ideas .  Also this drive should be capable of being used for bipolar as well as universal stepper motors.

Topic by arjunv8    |  last reply


Retractable mount for stepper motor

I am currently working on a small project which includes a 28BJY-48 stepper motor. I want to make a retractable mount for the motor so I can extend it to a desire length. What is the recommended way to do it? I thought about intalling two metaling poles inside the body of my device which will be connected to motor and to use pg16 glands as a twist-lock locking

Question by eliariev    |  last reply


Printer Stepper Motor Driver

I recently "Recycled" (parted out/junked) some Hewlett Packard 600 and 800 series printers. It occurred to me that everything I would try to build (electronic and software drivers) already exists in the printers. The motion of the stepper could easily be controlled by sending print commands to the "printer:. The only "problem" I can think of is satisfying all of the fault sensors, eg. out of paper etc. Has anyone worked on this. Recumbent Bike Builders Rule!! Carpe Ductum

Topic by naic98    |  last reply


stepper motor function as generator?

I want to make a stepper motor function as generator. Is it possible to do it if I don't want to hack the motor system? This is because, I cant change the principle of the motor itself. 

Question by SharifahA1    |  last reply


Best Way of Boosting 7.4VDC to 12VDC? Answered

I need to power two stepper motors off of 7.4VDC, and am trying to figure out the best, most cost efficient way.  What type of DC booster circuit would be best for this application? Do I need any noise filter? If yes, what kind? If I understand correctly, Stepper motors need a constant current. Does this limit my selection of DC boosters/step up devices?

Question by RocketPenguin    |  last reply