DTMF Generator with Arduino

Hello mate, I have telephone with only receiver and no keypad. So, i need to generate DTMF tones to dial the number. Is it possible for me to generate a DTMF tone generator by programming arduino with the frequencies and attaching speaker to it? Also, how can i club two tones which are required to be sent at a single moment? Thank You. 

Topic by anuragkanase 8 years ago  |  last reply 2 years ago


dtmf circuit problem?

This is the circuit for dtmf based robot using cd4514 for 16 outputs it has 2 l293d ic for controlling 4 motors will this work??

Question by agent555 4 years ago  |  last reply 4 years ago


how to make this DTMF ROBOT?

If this question is stupid plz  sorry I made a dtmf based bot ( car) using mt8870 ic   (without any programming) now i am trying to make another bot with some new features  i need to control 8 things  1 forward          -- when 2 is pressed                                  2  backward     -- 8 is pressed 3 left                 --  4 is pressed 4 right               --  6 is pressed 5 camera motor 1 forward and backward           -- 1 is pressed 6 camera motor 2 forward and backward           -- 3 is pressed 7 and two more motor forward and backward    --  7  is pressed 8 want to lit a led                                                --- 0 what will be the programming code i am using atmega 16  plz tell

Question by Mayoogh 4 years ago  |  last reply 4 years ago


Can Anyone tell me ATMEGA8 code for dtmf decoder in embedded c??

Question by ram_aloktripathi 7 years ago  |  last reply 7 years ago


how many dc motors can be controlled using dtmf decoder mt8870 ?

I am making a mobile controlled robot project using dtmf decoder ic i want to control 11 motors is it  possible and how which motor driver should i use and can i use atmega 8 or 16 

Question by townyw 4 years ago  |  last reply 4 years ago


how to connect a handsfree to a ring detector for the DTMF tones transmition??Cut out the earphone?

Im doing the cell phone control mobile robot...

Question by akirawind 9 years ago  |  last reply 9 years ago


Is this schematic CORRECT?

PLZ  anyone check this sch  it is the sch for mt8870 dtmf decoder  i wanted 16 outputs  is this sch correct  i dint place the crystal and other components

Question by Mayoogh 4 years ago  |  last reply 4 years ago


outputs for dtmf decoder ic?

How to get 16 outputs from a mt8870 dtmf decoder ic  will this circuit works ?

Question by Mayoogh_Girish 4 years ago  |  last reply 4 years ago


DTMF ht9170b How to connect mobile Tone ???

I work robotics

Question by Avadhut.Deshmukh 7 years ago  |  last reply 7 years ago


Hii..Could u plzz suggest me How to connect earphones to DTMF circuit?

Hii..Could u plzz suggest me How to connect earphones to DTMF circuit?..Its finding very diffult to judge wass d desire Terminal to interface to circuit..When i strip the wire one among the pair of wires, i find two thin wires with more insulated silk material..in this a brain feeding doubt arised that among these two thin wires which wire should be judge as Tip..Nd i bought a DTMF decoder CS9370DGP..is this is same as MT8870 specifications nd circuit?Plz do reply..nd if possibl plz post me circuit diagram using CS9370DGP..nd plz attach the stepwise pics that should follow while connecting the earphones to circuit..Plzzzzzz help me.......plzzz frnd:confused::(?

Question by nav.leo02 8 years ago


how to solder a push to on switch button??

Hi. i m currently makin a project regardin robo.its names robot control using dtmf. need to solder this s/w..replies expected soon! thank u~!

Question by dpanse 8 years ago  |  last reply 8 years ago


Plz anybody check this Schematic correct or not?

It is the sch for mt8870 dtmf decoder i wanted 16 outputs is this sch correct i dint place the crystal and other components

Question by Mayoogh 4 years ago  |  last reply 4 years ago


how to controll 2 additional motor for this robot ?

Hy  i saw this mobile operated robot  by Avadhut.Deshmukh and i am making one   Other than the 2 motors  used for controlling the robot  i need to control  2 more motor and 1 light (led) using mobile phone  some body plz tell me how can i do what should i do ??

Question by neymer 4 years ago


how to play sin waves(dtmf tone) in Netbeans ?

How to play dtmf tone in java netbeans  i am making to a software which will produce dtmf tone while pressing a buttons like this in fig 1 does anybody how to do this on netbeans plz tell me the code at least of one button (fig2) 

Question by agent555 4 years ago



12v and 5v Power Supply from 240v Answered

I am creating a home automation device that uses an arduino. The devices are connected to a relay. The real problem is I am using a using a DTMF decoder with the relay, while the relay works only with 12v power supply the DTMF decoder works only on 5v input (USB from computer to arduino). The devices that I know of are capable of converting a 240 v to 12v or 5v not both. What should be done so that I am able to get a 12v and a 5v from a normal 240v household power socket?

Question by NirmalMRaj 3 years ago  |  last reply 3 years ago


how can i make a connection between gsm phone and DTMF decoder?

I've seen the project cell phone operated robot and i'm enthusiastic to do it.(link : https://www.instructables.com/id/Cellphone_operated_Robot/)i have a motorla l6 phone with me and i'm planning to use that in the circuit. It has auto-answer option. But it has an USB port to connect the headset. If i want to use it, is it ok if cut one of the ear phones and connect the wire at the 2nd pin of DTMF IC?The next thing is what is the significance of word "RING" written at the ground in the circuit (left side at the bottom)

Question by vasu1012 10 years ago  |  last reply 10 years ago


Making a Telephone Function Without a Phone Line?

I have an old telephone desk set with a DTMF keypad. I was wondering if there was a way to some how get it to function without hooking it up to a telephone line, not to call people, but to make the DTMF tones, make it ring, and maybe be able to talk into the receiver. If you want to know why I would want to do this I'll just say I'm a musician, and I'd like to be able to run the phone into my mixer and use it like as an instrument. Also, yes I've seen the instructable about how to make a telephone receiver microphone, so no need to show me.

Topic by stuarttt 10 years ago  |  last reply 8 years ago


HAM radio repeater controller arduino

Is there anyone who can help me with a repeater controller, i need a little program which will switch according to input + 3 sec (or something like that) also i want to decode 4 bit paralel data (binary output from a DTMF decoder) and switch outputs accordingly (if correct code is pressed) (thins like identifier, time&date;, last transmitted message) thees functions i will make on separate boards, i just have to trigger them last transmission board needs an input from the arduino when to start, the playback will be done with one of the DTMF-code outputs any advise / code is wildly appreciated :) ps, im very new to arduino and have plenty to learn  kind regards, milan 

Topic by milanhofman 4 years ago  |  last reply 2 years ago


how to get 16 out from mt8870 using cd4028 IC?

I am making a robot using mt8870 dtmf ic i have read the data sheet it says the mt8870 have 16 outputs  how to get the 16 output  plz check this schma ( http://www.seekic.com/uploadfile/ic-circuit/200971333450883.gif )  how many 4028 will be needed 

Question by aniqa 4 years ago


c++ code hElp?

This is the code for mobile operated robot found from this site can somebody explain this code i didnt understand  the line which is Italic and Bold like this (DDRD=0xff;  DDRB=0×00) somebody plz tell me what the lines are CODE /* DTMF Controlled Robot PORTD pin 0,1,2,3 goes to motor driver l293d PORTB pin 0,1,2,3 is connected to output of CM8870 DTMF decoder IC */ #include #include int main(void) { DDRD=0xff; DDRB=0×00; while(1) { switch(PINB&0b00001111) { case 0b0010://Key 2 { PORTD=0x0A ;      //1010 both motor front continue; } case 0b0100://Key 4 { PORTD=0×02;    //0010 right motor front continue; } case 0b0101://Key 5 { PORTD=0x0F;//1111 SUDDEN STOP continue; } case 0b0110://Key 6 { PORTD=0×08;  //1000 left motor front continue; } case 0b1000://Key 8 { PORTD=0×05; continue; } default: continue; } }//end of switch return 0; } // // // //

Question by agent555 4 years ago


Could u plz gimme the use of IC CS9370DGP?

1stly i went to purchase the IC MT8870 for dtmf decoder..he gav me dis cs9370DGP nd said disz is new one nd it works like MT8870..bt i got a doubt whether it works vth the circuit built using MT8870..plz kindly gimme some suggestions.. if possibl plz provide me the circuit for mobil control robot using cs9370DGP.. Plzzzzzzzzzzz:(

Question by nav.leo02 8 years ago  |  last reply 8 years ago


how can I use a mobile phone dmtf tones to turn on PC parallel port pins on and off using VB, C or C++ code?

I need to be able to turn on ac powered lights from my pc parallel port using my phone. The set up I have uses two relays to put on the ac lines. Am currently using a web interface to do it. I dont want to rely on SMS. Suggestions that use SMS are welcome though. Any help will be appreciated.

Question by firstkenyan 10 years ago  |  last reply 7 years ago


IP-phonet on Promotron

• Support SIP 2.0, TCP/UDP/IP, RTP/RTCP, HTTP, HTTPS, ICMP, ARP, DHCP, NTP/SNTP, TFTP protocols.• Support STUN and symmetric RTP for NAT.• Interoperable with various 3rd party SIP end user device, Proxy/Registrar Server, and gateway products.• Advanced 32bit embed MCU + DSP technology to ensure superior audio quality.• Advanced adaptive jitter buffer control, packet delay and loss concealment technology.• Support popular vocoders including G.723, G.729A, G.711(a-law and u-law), G.726(40K/32K/24K/16K).• Support standard voice feature such as Caller ID Display, Call Waiting, Hold, Transfer, in-band and out-of-band DTMF,three way conference.• Support Silence Suppression, VAD(Voice Activity Detection), CNG(Comfort Noise Generation), Line Echo Cancellation(G.168), and AGC(Automatic Gain Control)• PSTN pass through port, with auto switch between PSTN and VOIP on inbound call and manual switch on outbound call. It becomes PSTN phone when unit power is off.Linkman:EricaSkype: erica888wQQ: 541006495MSN: w888160@hotmail.comTel: +86-755-22015114, 27918959, 26626155 LEAD TECHNOLOG DEVELOPMENT CO., LTDWeb:www.elecic.com

Topic by cobbyzhou 12 years ago  |  last reply 12 years ago


support SIP, Mutil-user managerment, international professional communication IC gateway with one,two,four port on sale

Call Features1. 3-way Conference2. Auto Answer3. Call History- Most Recently Missed Calls- Most Recently Received Calls- Most Recently Dialed Numbers4. Call Hold5. Call Forwarding6. Call Mute7. Call Rejection8. Call Transfer9. Flexible dial map10. Call Waiting11. Caller ID12. Do Not Disturb (DND)13. DTMF Relay- In-band, Out-band and SIP Info 14. Hotline15. support SIP domain, DNS name i. of server16. Multiple Proxy, Registrar, Redirect Servers17. Supports 2 service domains18. Volume AdjustmentManagement1. Firmware Upgradeable2. Upgrade firmware through boot monitor3. Config through Web, Telnet 4. Upgrade firmware and configuration file i. through HTTP, FTP, TFTP5. Support Syslog6. ND5 EncryptionProtocols1. SIP RFC3261 RFC3262 RFC3265i. Backward Compatible with RFC25432. SDP (RFC2327)3. RTP/RTCP (RFC1889 and RFC1890)4. NAPTR for SIP URI Lookup (RFC2915)5. STUN (RFC 3489)6. ARP/RARP (RFC 826/903)7. SNTP (RFC 2030)8. DHCP/PPPoE9. HTTP Server for Web Management10. TFTP/HTTP for firmware upgrade11. DHCP Option Codes for SIP (RFC3361)12. 802.1P TOSApplications1. Voice Mail Integration2. NAT Traversala) Static NAT Routeb) Traversal by STUN/UPNP3. Support Firewall4. Support Route/Bridge mode I/O Interfaces1. 2 RJ-452. Dual 10/100 Switched Ethernet Port3. 1 RJ11 for Phone(FXS) , 1 RJ11 for LifelineUSB-phone

Topic by cobbyzhou 12 years ago


Do you want to use Skype out more comfortable and convenient

Inside 128M USB Disk. It can be changed as the clients wish 128*64 Dot Matrix LCM, it can show multi-language and information of calls wonderfully It can show the date and time Compatible with VoIP (Voice over Internet Protocol) solution such as SKYPE It can make a PC-to-PC calls for free and PC to PSTN or MOBILE calls through Internet. Echo-cancellation for better sound quality Can set speed dials, design as mobile phone There is a DTMF dialing keyboard, can dial on the phone as normal phone Can make a call to SKYPE by using SKYPE software, or make a call to normal phone by SKYPE out Professional processor and special arithmetic for high timbre quality Use I2C port, more simply and convenient Inside LED, shows the statement of coming calls, calls, silence, dialing, on hook, name list It can save the received calls and the dialed number as many as you wish It can make a call through SKYPE calling list Several types of ring tones for incoming call alert, The display of USB Phone and SKYPE can be concurrence As a speaker to broadcast music from PC No need superfluity power supply Can adjust the volume during a call Connecting statement auto-checking No need to bear the ‘earphone and microphone’, just answer the phone when it rings One phone for VoIP, make it more convenient Can use as the earphone of Yahoo Messenger, MSN Messenger, MS NetMeeting, Talk and so on, supports dialing by USB We can exploit more functions according to the customer's inner information about the operation details So if you have any requirement of VoIP equipment, please contact us. TEL:+86-755-27918959 MSN: cobbyzhou@hotmail.com Skype: cobbyzhou Yahoo Massager: cobby_zhou E-mail: cobbyzhou@hotmail.com

Topic by cobbyzhou 12 years ago  |  last reply 12 years ago