Search for enclosures in Topics


Speaker Enclosure

Can i make Speaker Enclosure with plaster of paris?

Question by Ansif  


What material is used for car convertible tops-rear window? I want to enclose a porch?

I want to enclose a porch with 4X8 foot framed windows using this material for the window-rear window convertible "plastic"?

Question by Golfright    |  last reply


what can i use to store my 3.5 hard drives, looking for common items to up-cycle / re-purpose

I have a bunch of hard drives  that i want to put into something better than the anti static bags. i did see some cheap enclosures for 3 bucks from china, they are made out of plastic.  reviews state that they are very tight and the hinges break quickly.  i was wondering if there are any items /boxes that would work to keep them in.  i use  the hdd drop in readers, so i just need to find some decent enclosures to stack them safely.There must be a food box that would be a good fit. Thanks for any help.

Topic by escapefromyonkers    |  last reply


usb enclosure hack

Current inventory: 2 Seagate ST340015A IDE hds (40 gb each) 1 Rosewill External usb 2 ide enclosure (pl2506 controller chipset) 1 40 conductor ide cable (mobo-slave-master) soldering iron/solder way, wayyy to much free time. OK, given the above items, is it possible to run both drives at the same time from the one enclosure? Fitting inside the enclosure is not an issue. So far, I have removed the original ide cable the came with the enclosure controller. And, installed my own ide cable. The only drive that is detected is the one jumpered as master, at either location on the cable(master vs slave). No matter what the other drive is jumpered as(slave, cable select), it is not detected. I tried setting both as master and neither are recognized. I have run out of ideas... suggestions would be great. And please dont suggest getting another enclosure. IM CHEAP!

Topic by danman1453    |  last reply


Lightweight Speaker Enclosure

Im coming up to the third (hopefully waterproof) upgrade of my longboard mounted speakers. Im looking for something pre-made like a square pipe or storage box etc, that i can use as an enclosure that has flat ends large enough to mount 6.5" PA speakers onto, is no wider than 8" and no longer than 2ft. It needs to be as lightweight but rigid as possible. Any ideas/links?

Topic by ambientvoid    |  last reply


Custom Electronics Project Enclosures

I need to have a custom enclosure made for my senior design project. It has to be placed on the back of a hand and thus have some curve to it to hug around the hand. Also, it can not be much bigger than about the size of a deck of cards. Most places I've found only have rectangular enclosures. Does anybody know of a place that could fabricate the custom design I described? Any help would be greatly appreciated!

Topic by Mungerbees    |  last reply


Connecting the ground to my enclosure?

I'm building gmoon's Valvelitzer inside a utility box. I've just realized that the entire enclosure is going to be grounded, meaning it's going to be directly connected to the negative pole of the power supply, which seems to run at 14V 2.2A (It'll be regulated at 12v before it gets to the tube). Is this dangerous? If it isn't, should I just solder all the ground points to the enclosure? If I run the power along the enclosure, is that going to cause some extra capacitance? Is that bad?

Question by flagrantfouler    |  last reply


Enclosure for LED bar graph

I just bought an LED bar graph for my project. I'm looking for an enclosure that I can install this bar graph. Are there any vendors or services where you can specify precut holes or am I restricted to a DIY with saws and drills? http://www.ebay.com/itm/2-pcs-TriColor-Fixed-LED-Bargraph-Array-20-Segments-for-Audio-VU-Meter-USA-/181403879518?pt=LH_DefaultDomain_0&hash;=item2a3c83885e

Topic by MikeH8    |  last reply


Dual Hard Drive Enclosure

Hey i'm work'n on use'n and old computer as a harddrive enclosure. So it house 4 or more hard drives i seen where you can buy one but you know how the site works it is better if we make them. I have like 20 160gig harddrives needed some thing to do with them. Any help would be great.

Topic by nabzaf    |  last reply


Extending the port of a ported subwoofer enclosure? Answered

I'm planning to pimp out my car, i was wondering... If i design my own subwoofer enclosure, i want to extend the port, so that the enclosure is vented right inside the car (not the trunk) if i did that, would i have to re-calculate port diameter? thanks!

Question by Sandisk1duo    |  last reply


Steps to creating a custom project enclosure

I'm in the process of trying to design a prototype for a custom electronics project. I have a 3d printer at my disposal and I would like to print out my initial prototype and at a later time get the enclosures injection molded. I'm looking for some advice on a starting point. Is there some sort of standard model I can start with? or do people typically always design these from scratch. Does any one have recommendations on a place that could do a short run of injection molded enclosures? any advice or starting points would be helpful 

Topic by ouchthathurt    |  last reply


Two 4" Drivers in one enclosure?

I want  a very deep Bass as i am getting in my logitech z103...(image attached) I am plannin' to build a sealed 10" cube outta 0.5" thick Plywood and put in em two 4" subwoofer drivers. will i be getting the thing i want???? if not what should be the dimensions???? THnaks in advance!!!

Question by adarshnarsaria    |  last reply


Too big enclosure for sub woofer?

Last year had a lot of bad luck making my bike sound system. I made some boxes, fried some electronics, etc. The boxes were too big for easy handling, so I'll make another attempt, since spring is coming. I noticed the speaker (driver) did not like higher volumes; very large excursions in the lower Hz range , probably hitting the end of its moving range. It is a closed enclosure, no port. The RMS output of the amp is probably many times lower than the RMS rating of the speaker (driver); logitech 2.1 computer amp with consumer grade sub speaker (6"). Same problem occurs with my home 10" 60 W RMS driver in a closed ca. 70 l - ca.15 Gallon barrel, with a modest 25W RMS amp: I cannot even turn it halfway up:  it is mounted horizontally, and shoots peas 40 cm (16") up! Would it be more helpful to make the box / barrel less square? Like halve the size by putting a diagonal separator in the box? Or is geometry irrelevant and does only volume matter? Perhaps there even might be a formula????

Question by BobS  


Advice on building a RC projector enclosure

I have a video projector mounted on the underside of a moveable wood panel on my patio ceiling (see pic, the yellow plastic would be removed) that I'd like to build an enclosure for that won't break the bank. Since it is too high to reach, ideally (with some help) I can construct an enclosure for when it is not in use, that I can remotely adjust to use the projector (for example; via linear actuator or screw drive, etc.). The challenge is the projector has fans and cooling vents on the sides which need clearance to be effective, so three sides of the projector must be clear (the third is the front w/ the lens). All told, the vertical distance of movement for this clearance would be about 4-6". While I'm not well versed in this kind of small motor/arduino/circuitry construction, I'm pretty handy and am confident I can figure it out with some help. I have found many examples of RC box openers with hinged lids, but in all these hinged designs there would not be enough side clearance for the vents. I hope my description was not too confusing, I am open to any and all suggestions. Thanks!

Topic by STRobo  


Is a Wooden Enclosure for Electronics a Good Idea? Answered

I am in the process of converting my ATX power supply into a bench power supply. My PSU's standard case is made from 1mm steel with various ventilation holes, there is also a 120*120mm fan.  However, the circuit board is strangely positioned within the case and there isn't enough space for what I want to add.   I would like to take all of the electronics and rehouse them in a home-made wooden case. My question is; Is this a sensible thing to do? I plan to use 5mm pine stripwood to remake the box, but slightly bigger and better arranged. I would still fit the fan and drill plenty of ventilation holes.  Do I need to take any extra precautions if using wood, or is it just a really bad idea. Thanks in advance. 

Question by R055_28    |  last reply


subwoofer and normal speaker combo in same enclosure?

Is it necessary for subwoofer to be in an individual enclosure ? can't a normal speaker n subwoofer be in the same enclosure ? what happens if they are in same enclosure ? and what  "exceptional" happens if subwoofer is in individual enclosure ? thank you SO much in advance ! i really wanna know this thing

Question by mcsk8rg    |  last reply


Diy ipod shuffle shell enclosure source?

Does anyone know if anyone sells ipod shuffle-like enclosures (more specifically similar to that of the Fiio E5)?  I would like to use one to house a project.

Topic by guyfrom7up  


potentiometers: How thick is the enclosure allowed to be, how can I fix them inside the enclosure? Answered

So in a nutshell: I'm following an instructable where potentiometers are used which i was never working with before. Those potentiometers are covered with some potentiometer-knobs which are between the enclosure and the potentiometers. And now I have some questions ... a) how do I fix / secure the potentiometers inside the enclosure so they don't move when I turn them, but the potentiometer-knobs do, and b) how thick is the enclosure allowed to be when I use 500K, 5% tolerance potentiometers? This is so frustratingly confusing.

Question by Skelpolu    |  last reply


Is it ok to put 2 subwoofers in a single sealed enclosure? Answered

Is it ok to put 2 subwoofers (wired in series) in a single sealed enclosure or should they be seperated? My worry is that the single sealed enclosure may cause too much pressure rather than adding more pop to the sound.

Question by Andale_The_Great    |  last reply


Could a 3D printed sealed speaker enclosure printed as separate parts be bonded together well enough to function properly?

I want to try 3D printing a sealed speaker enclosure but the size of enclosure that i need will be 4 times the size of my printers build space so if i divide the enclosure model into quarters what would be my best method of bonding those pieces together into a container that will be mostly airtight once the speakers are in place?

Question by ambientvoid    |  last reply


Can I use a 3.5" hardrive enclosure for 2.5" harddisks (SATA)?

Will it damage my harddrive if I use a 3.5" hardrive enclosure for 2.5" harddisks (SATA)? The connectors are the same...

Question by Fypsigon    |  last reply


Hard drive enclosure to turn internal into external?

Hello all, I have what may be a dumb question - so hopefully it will be an easy one to answer! I have a couple old hard drives from old computers that I want to put into a case/enclosure to repurpose into an extra external hard drive. When I take exact measurements of the hard drives they are: 4" x 5 3/4' x 1 (W x L x D). I've been looking around for enclosure kits but I don't see any that are 4" in width. I see a lot of 3.5" and not many others besides smaller 2.5" casings. So my possibly stupid question is: Do I want the 3.5" enclosure for my hard drive? I know that sometimes the sizings can be off when it comes to stuff like this. Thanks for the help, RW

Topic by thefuturism    |  last reply


add motherboard stand-offs to an RS enclosure?

I need to connect the board from a PC ATX power supply to a Plastic Radio Shack project enclosure. as a part of my ventilation / grounding scheme I've got the power supply on standard brass motherboard stand-offs. I don't want to connect any hardware through the case, for insulation purposes. I need a good way to hold the stand-offs (and by extension the power supply) sturdily in place... preferably with bits I can get locally (hardware store or RS)... Any Ideas?

Topic by gschoppe    |  last reply


Is a sealed environment always better for speaker enclosures?

Specifically when dealing with smaller, less powerful speaker. I am aware that certain sub woofers require venting, but I don't know how important sealed boxes are for midrange and tweeter.

Question by Andale_The_Great    |  last reply


External Hard Drive enclosure for eSATAp connection

Hey, I want to buy a Power over eSATA kit (aka eSATAp) to use with 3.5inch internal hard drives (which are cheaper and faster than laptop 2,5inch drives). I'll be using it on desktop computers on and off, so the higher power consumption of desktop drives is not the issue. Thing is, I want to enclose the internal 3.5inch hard disk in something, for transport. Some case that leaves room for the cable connection (see GIF). Does anyone know if I can adapt existing SATA hard disk enclosures? Or if there is some boxy-thingy out there that I can best adapt to suit my purpose? I was looking for an instructable on this but couldn't find any. Thanks!

Topic by akaleeroy    |  last reply


What is the best smallish enclosure for a coffee maker type heating element?

I'm wanting to start a project involving the use of an old coffee maker heating element. I don't know what type of safe enclosure to put it in to keep it separate from the wood fixture it will be attached to. Any ideas?

Question by jimjobe    |  last reply


What would make good cat enclosure toys?

I have a cat enclosure attached to my house for my cats but it's just a bit of grass and a fence. How can I make it more interesting for them without spending hundreds of dollars on accessories from the company that built the enclosure? I don't really know where to start other than maybe hanging something from the top as a toy they can bat around but I'm worried that they'll either break the toy, break the netting or hurt themselves. I've considered a scratching post but I don't know how to make a waterproof one and carpet's kinda out :/

Question by PaigeGrel    |  last reply


What hard drive enclosure should i get for this hard drive? Answered

I've got a harddrive from my dead laptop that i'd like to use as an external, but i don't know what enclosure to get. This is the hard drive  and i've attatched a picture of the connection. i already bought one enclosure, but it had the wrong connector, so i really would rather not mess up again. : / also, i know, crappy pic, sorry

Question by cyc4015    |  last reply


What are some of the factors to take care of while designing an EMI/RFI shielded Enclosure?

Are there any constraints on material used and wall thickness?

Question by vinod nicholas    |  last reply


if you added a second speaker instead of a port in the enclosure, what effect would that have on the sound?

I know that if you have a ported enclosure on a subwoofer its louder and if its sealed its more precise,  but what would happen if you put a second subwoofer in the enclosure instead of a port? what would the effect be? im just curious.

Question by tokymaru    |  last reply


2.5 HD Enclosure case copying files from Internal 2nd HD, 2.5 case stopped working, help ?

I recently purchased a 2.5 HD Enclosure Case with USB cables and it worked fine while reading an old 2.5 HD that I inserted in it. When I was copying files from an 2nd Internal HD, it was copying fine then noted. file in use, stopped copying, turned off computer, now I can't get the 2.5 Enclosure Case, with a HD in it, to be seen on my computer with the other HD's and USB's. Was the HD that I was copying to ruined or can I restore it in a procedure ? I would really appreciate anyone's assistance to fix the problem with the 2.5 HD Enclosure case that is not being seen on my computer, even tho the red light is on noting that it is connected via USB. Thanks.   mjy88keys  

Question by mjp88keys    |  last reply


Best adhesive for securing plastic enclosure to silicone surface?

I am getting a silicone rubber skin/case for my Kindle in order to make a custom mount.  In addition I need to put a compartment on the back of the case to house some electronics components.  It will be put inside of a plastic enclosure, so I need to figure out how to secure that plastic enclosure to the back of the silicone case.  I was thinking of using Velcro, but I don't know if that is secure enough, or if the adhesive backing is strong enough for either the plastic or silicone surfaces.  What would be the best kind of adhesive in this situation?

Question by dmehling1    |  last reply


Can you make a external hard drive from an old internal hard drive without buying a hard drive enclosure?

I got several internal hard drives and want to make a couple of them into external hard drives. I don't have a way to buy any hard drive enclosures and would like to avoid buying enclosures completely.

Question by SleepyDude    |  last reply


How do i build a weatherproof, dust proof video projector enclosure with good airflow for use in a desert enviroment?

I'm going to be using a projector in the desert at night and need to build an enclosure for it. The enclosure will have to have a serious filtering system to keep blowing sand and dust out, it also will have to be able to block any rain that just might fall. While doing all that it must push alot of air out of the box to keep the projector cool enough. It does NOT need climate control because the desert gets really cool at night when ill be using this unit. Ideas?

Question    |  last reply


would 4 speakers on two 2-channel amps require twice as much power as 2 speakers on one 2-channel amp?

Also how do i work out the recommended (capacity) volume of the enclosure for 2 or 4 speakers? would it being used outside require a larger enclosure than usual to adequately broadcast sound?

Topic by ambientvoid    |  last reply


All weather enclosure for a dual axis solar tracker

I am looking for ideas on how to modify the attached solar tracker, that it fits into an all weather container/box. also it needs  to be easily dismount/mounted during the summer month. https://www.instructables.com/id/Simple-Dual-Axis-Solar-Tracker/

Topic by Deanv1  


Thoughts for a fan for venting a homemade 3D printer enclosure?

Hello all, I'm in the early stages of building my own enclosure for my 3D printer. I'm going the route of building it using Ikea Lack tables. I'd very much like to put in a fan to vent the fumes from printing out the window via a hose. Originally, I was going to use a USB fan, but I'm starting to wonder if that will move enough air to make any difference. I was going to go with USB because I have no electrical work skills. I'm curious if any of you have thoughts, or have already come up with solutions for this. I'd be interested to hear any suggestions or advice anyone has. Thanks!

Topic by JesterPoet    |  last reply


I want to build a Transmission Line/ T-Line Subwoofer Enclosure

 I have been wanting to build a Transmission Line subwoofer enclosure to house 2 10 inch subwoofers. I'm not exactly sure what subwoofers I will be using yet, or the specifications on them yet either. The only thing that I am worried about while constructing this box, is the calculations. I am good in math, and geometry and all of that stuff, but I don't know where to start. If someone could take a moment and explain to me what the calculations and the steps that would be needed to construct such an enclosure, it would be much appreciated. Thank you. 

Question by brandencota    |  last reply


How do i make my subwoofer enclosure look cooler?

Hey fellow 'instuctors', i'm gonna be making another subwoofer enclosure soon, an i want to know how i can connect a few LED's, or Neons to the box, just to make it a little more unique. I know it's got something to do with wiring the LED/Neon's in series to the loom to the subwoofer itself. If anyone know's anything, or know any webpages i can visit, i would greatly appreciate the help.

Question by nmesis_02    |  last reply


how can i connect dvd rom to laptop?

I have netbook and want to connect dvd rom via enclosure,but when i connect it it only appears,that device is installed.nothing in computer (i got win7 and asus 1215b) how can i create dvd rom in computer?

Question by burbanowicz    |  last reply


What are the guidelines for your power voltage path in your audio project?

Are you supposed to avoid crossing it over your audio signal, or parallel to it, or across or parallel to your ground wire?  And if the enclosure is grounded, should you avoid running it against the enclosure?

Question by flagrantfouler    |  last reply


8 Track Player External HDD?

Parts 1) broken lacie 500 gig eHDD or multibay sata - USB/firewire 2) old 8 track recorder I wanted to use the 8 track recorder as a eHDD enclosure. Does anyone know where I can buy just the sata - usb multibay / power boards? I basically need everything for a multibay enclosure except for the enclosure. I just don't know what they are called. THANKS!

Question by heartxcore803    |  last reply


How can i make a USB external hard drive enclosure from scrach?

For SATA drives to use in Win XP / Vista before any one starts they go for about 350 of Brazilian money thats about 175 USD and I am very capable of making one my self

Question by cassiorichiniti    |  last reply


WHAT GIVES WHERES MY FLOPPY THREAD?!?

Sorry folks looks like the server screwed up my posting and i'll have to post my idea for home brewed 5.25in floppies all over again (the post eventually appeared several hours later so i deleted it) ok so where to start (*light bulb appears over head*) i got it if you have a 5.25in floppy get it out and look at it you'll notice that its pretty simple the first part you will notice is the plastic envelope enclosure thing which is just a single piece of folded plastic with some holes cut in it, just below the surface of the enclosure is a fabric or paper dust trap that keeps the disk debris free and finally comes the hard part the disk each disk has 3 components the iron oxide powder, the disk, and the binding glue stuff the holds the powder to the disk. now here is my crude theoretical unproven construction process 1. cut out the enclosure(i'm thinking a material like plastic card stock might work) (probable impossible by hand put it under a laser cutter or watter jet if you have one) 2.use 8 dabs of glue to glue the dust trap in place on the side of the enclosure that will come in contact with the disk 3.spray some adhesive onto the disk and bury it in iron oxide powder 4.remove the excess powder and spray it again with adhesive 5.carefully put the disk in the enclosure and fold the enclosure around it gluing the enclosure shut 6.stick it in your floppy drive and format it i'll have time to try this myself this summer until then feel free the criticize and question my sanity just PLEASE don't suggest buying disks from e-bay, thrift stores, flee markets, online, or any where else for that matter

Topic by clasic_traveller_diehard    |  last reply


Challenge

Since subscribing to Instructables I have found this to be one of the best and most interesting investments I have ever made.  I do offer a challenge to those interested in computer hardware.  I removed a Seagate 4.5 inch SATA hard drive from my old computer.  I would now like to recover some files from this hard drive.  However, I cannot find anywhere I can purchase a suitable hard drive enclosure which can be connected to and accessed by a computer through a USB port.  Seagate cannot help.  Is any subscriber to Instructables able to design and construct such an enclosure?  There must be a large number of people who have a similar problem.  Would anyone like to meet the challenge?

Topic by kalkat78    |  last reply



WATER TURTLE OUTDOOR HABITAT IN TX?

So My Male RedEared Slider is Gettin To Big to be in a tank inside, So ive decided he needs a pond habitat outside! i want to make an above ground enclosure with waterfall filter i just need some help with ideas on getting started HELP! lol THANKS MUCH IN ADVANCE ^_^ 

Question by Brujita Kitty in TX    |  last reply


What are these devices consisting of audio jack and LED(s) OR IR-transistors OR similar looking parts? Answered

I was cleaning in the office I work in and found these two devices on the picture. Now I'm curious what are these for as I couldn't derive the purpose from the looks. One of them has a mono 3.5mm audio jack and two LEDs or similar looking parts - 5mm round transparent things. One side of the enclosure around each "LED" has a sticky tape. If they would be attached to something then the "LED" would face 45 degrees from the surface. The other has a stereo 2.5 mm audio jack and one dark IR-reciver-like thing in a small round enclosure. The enclosure has two small holes on the other side, but I'm not sure if they are important. I tried the one with two "LED"-s in a headphone socket but nothing happened.

Question by Libahunt    |  last reply


IS Poly corbanate plastic is flexible?

Can any body tell me that ,whether the poly carbonate is flexible?If it is flexible, please tell the life time of the flexible PC

Question by suresh product engineer    |  last reply


Can someone explane how to build a waterproof cabinet for an LCD or Plasma Telivision?

I want to build an enclosure for my television to withstand the floridian climate

Question by mcatnova    |  last reply