So, microcontrollers. What are they, how do I use them, where can I get them,and the likes. Oh, and is it possible to pull them off of circuits and stuff?
Question by LiquidLightning 8 years ago | last reply 8 years ago
I'm looking for a cheap microcontroller that i can use to control at least 3 led's. All they have to do is flash very quickly at different speeds. I dont have any experience with microcontrollers but i do have limited programming knowledge. Suggestions?
Question by robbienakata 10 years ago | last reply 7 years ago
Hey everyone. Long-time member of the site, but just now starting to get into microcontrollers. Looking for some help on choosing a good, easy line of microcontrollers/programmer (easy to use without sacrificing too much function) which would be good for someone new to microcontrollers. Would the ATTiny line of microcontrollers be any good, or would pic be better? Oh, I'm also a university student so cost of the microcontroller/programmer is something I'd like to keep low (if possible). Thanks to anyone who might be able to help me. Either respond here or send me a private message ... Thanks again :)
Topic by Murf 11 years ago | last reply 11 years ago
hi to all!!! can somebody teach me how to program the z8f042a microcontroller that controls a 9x6 LED matrix having different patterns...and i'm using a rotary switch for each pattern...please!!!! it can be 6 patterns...
Topic by janesan_14 8 years ago | last reply 8 years ago
I have a few MSP430F5438IPZR microcontrollers from texas instruments, and i was wondering how to program them. I've seen things like the ghetto programmer and was hoping that i could do something similar. yes i am new at microcontrollers, i have done nothing with them, but would like to start. any help would be appriciated. MSP430F5438IPZR data sheet thanks EDIT: i would like to know how to connect it to the computer and then program it.
Question by matstermind 8 years ago | last reply 8 years ago
Paragraph 4 of the official rules of the microcontroller contest states that the deadline for entry is August 25, 2014. The front page bullet points states the deadline is November 10, 2014. These should be consistent. Which is the correct data?
Topic by waltx 4 years ago | last reply 4 years ago
Looking for micro controller for pool robot was built in 2001 controller part numbers seem to be 116a or diag 116a can i use a different microcontroller or do I have to use this model.Any help would be nice. thanks and have nice night.!!! Randy D
Topic by randy D 10 years ago
Non of the online tutorials are helping me, How do i set a high/low output to a SPECIFIC pin on my AT2313 tiny??? All I fine alone is OUT PORTD,0xFF which sets ALL ports on portD to high 255 aka OFF. But How can i set like pin 4 (PD4 aka PortD 4) and not all portD? someone help me!!
Topic by Killa-X 11 years ago | last reply 11 years ago
Hi i got aPICkit 2 Debug Express kithttp://www.microchipdirect.com/productsearch.aspx?Keywords=PICkit+2+Debug+Expressand a PICkit 2 Low Pin Count Demo Board http://www.microchipdirect.com/productsearch.aspx?Keywords=DM164120-1for my birthday and i was wandering where can i go to get started with it and what can be created using them. all help will be greatful thanks =)
Topic by jimbojonesy 10 years ago | last reply 10 years ago
Hello. I'm just making my entrance into the world of microcontrollers. But as I self learning everything I have a few questions. I recently purchased 2 PICS (16F648A) and a programming board. The board works fine and I got it to connect to the computer and reconize the PIC. I guess my first question is, Is all hex code PIC specific? Meaning would I be able to use this code "http://www.voti.nl/blink/index_1.html#16F630" for my PIC? The models are very similar but not exact. If not, I would like to do the standard "Blink an LED" as my first project. How would I write my code for this PIC and what materials would I need? Thanks!
Topic by jefferson987 11 years ago | last reply 7 years ago
Hi everyone I have got a MICROCHIP - PIC16F616 to play with, I am going to write a little program and load on it. http://onecall.farnell.com/microchip/pic16f616-i-p/8bit-flash-mcu-smd-16f616-dip14/dp/1332199?Ntt=1332199 However, I have a few questions before I do this. 1. How do I know whether language I should write? like C or Assembly? does it tell you in the datasheet (link above), because I don't seem to find it. 2. What kind of program do I need for loading the program into the chip? is it also an information I can find in the datasheet? or it is really some common sense between programmer. My supervisor doesn't offer much help... Extra question Here is the link of open programming, I am just curcious that if I build this programmer (I have one for my chip, but just wanna learn something), does it mean that I can use this to connect my microcontroller and my computer, so to load the program into the microcontroller? http://openprog.altervista.org/OP_eng.html Many thanks
Question by luckyvictor 8 years ago | last reply 7 years ago
Hiya guys is there anyone that can guide me to finding an instructable that deals with interaction in remote places using a micro-controller. For instance people in 2 different locations in the world, want to engage or enhance social bond or interaction by using a motion or proximity sensor and internet of things for instance triggering a sound or an led light that can be sensed in a remote location. So one location motion is detected and the other location this detection can also be seen, if that makes sense? For instance similar to this kind of project http://goodnightlamp.com/ Could this be done? Thanks
Topic by Snowcoat 3 years ago | last reply 3 years ago
Hi, to make a long story short i don't want to have to go into the cupboard and turn on my amp every time i plug it in, it has a button on it that needs to be pressed about 5 secs after power is turned on and then left like that, could i take a feed off the power supply, connect it to the 555 or another ic and make it activate a transistor 5 secs after power was applied? i only need it to do this once every startup, i don't want it pulsing on and off and it needs to be as simple as. thanks, luke
Question by ljarrald 8 years ago | last reply 8 years ago
Hi, i'm new to microcontrollers and I want to make a Usb powered and controlled 5 x 20 Led array using charlieplexing, and I have a few questions: - Is there only 1 led on at a time when charlieplexing? - What microcontroller should I use? - Is there a good instructable on connecting a USB to a microcontroller? (i've searched) - Does anyone have a suggestion for a programmer. Thank You, Sander
Topic by DELETED_svkatwijk 10 years ago | last reply 10 years ago
Hi all, I need to use a microcontroller for my project and am thinking of getting the arduino UNO R3 development board which composes of the ATmega328 microcontroller. I have to connect a small motor, a 16x2 LCD display and a miniature heating element to the arduino. I would like to know if the UNO R3 is suitable for my project. PS: I am very new and noob regarding microcontrollers
Topic by kurtselva 6 years ago | last reply 6 years ago
So I took apart a remote control for a cheap helicopter. There is a 14 pin microcontroller on board. Unfortunately it looks like any other 14 pin IC out there and there are no markings on it. Is there anyway to identify possibilities. For example if I mapped where each pin goes on the PCB. Luke pin one goes to the LED's, pin 2 goes to the joystick, etc. Is there any way to "read" the chip to figure out what it might be?
Question by MDheliMech 5 years ago | last reply 5 years ago
I need your help in my graduation project It is a smart home project in which i am using two PIC micro-controllers PIC16f877A for LCD & Keypad which is a way of devices control connected to the main micro PIC18f4550 i have problems in main micro code could you help me please I am trying to achieve multi way home automation with some security like fire system and recording camera . one micro for lcd and keypad connection. another to handle interrupts coming from different ways of devices control like keypad , GSM messages serially connected , C# windows application USB connected and remote. my code https://drive.google.com/open?id=0B7jw0zvYc42cdmJPbGRzOWQ0MW8&authuser;=0
Question by AhmedA52 4 years ago | last reply 4 years ago
Hello I am a newbie to the world of microcontrollers and would be really grateful for some advice about choosing one. Basically, I’m doing a final year university engineering project that requires an MCU to take a number of analogue inputs, do some processing, and spit out an analogue output that will drive a loudspeaker. My supervisor has recommended looking at the Philips LPC2148 and associated development kits (http://www.olimex.com/dev/lpc-h2148.html) because it is cheap and looks able to fulfil the following requirements: I/O – three analogue inputs (so 3 ADCs), 3 digital inputs (two servos and a bus for programming the controller), and one analogue output (requiring a DAC either built into the development board, or one I could connect on an add-on board) Speed – a program size of about 500 floating pt operations, processing samples at a rate of up to 400/second, hence of the order 200,000 floating pt operations per second. I think the LPC2148 uses fixed pt arithmetic so would need to perform the equivalent of this in fixed pt. Support – in place debugging support would be desirable; ability to be run on Windows; overall hardware and software cost of £100 or less. Does this chip and its development tools look up to the job? If not, would you recommend an alternative? Are there any other major criteria I’m neglecting in the process of selecting a MCU? Many thanks, Sam
Topic by samtheengineer 7 years ago | last reply 7 years ago
Well I have been opening things like VHS, DVD players Computers and a lot of other things ( since my family is not the richest around we usually buy stuff second hand ) But even if we did get new stuff I would probably be the same. I am a curious kid by nature ( it must be a hundred times i heard the line curiosity killed the cat from teachers to even my family and friends ) Ok so to the question What are these microchips/controllers What ever they are. Like how could I use one if I would be able to get them out of the circuit? I heard they get programed to do something. How do i program one? Why do the circuit always so complicated?
Question by bug on fire 10 years ago | last reply 10 years ago
Hi friends, I am doing a project based on obstacle detector. It is a outdoor project hence i choose to buy an ultrasonic sensor to work efficiently on both bright sun light as well as dark nights. Now my problem is i am not able to interface this sensor with my controller. Anyone please tell me what input i must give to trig input of that sensor and what kind of output i get form the echo pin. also tell me how can i interface this sensor with the AT89S52. i have attached the user manual which i downloaded from internet. Please help me with your valuable comments, Thanks in advance.
Topic by knachuthan 4 years ago | last reply 3 years ago
What is the difference between a picaxe 08 microcontroller and a 08M microcontroller? is the 08m better? If so for what reason?
Question by Barramundi 9 years ago | last reply 9 years ago
Question by samuel .j 8 years ago | last reply 7 years ago
hi.i am new to the world of microcontrollers..i want to use a attiny microcontroller for my project.but i have no idea about it in terms of the usage,availability,programming...please help me with it......
Question by ishaan_kakar 7 years ago | last reply 7 years ago
I am an Electronics beginner and i really need help...
Question by sukhmanattwal 6 years ago | last reply 6 years ago
Tonnes of instructables are based on microcontrollers, and i can't seem to find any. I can't get anything off of the internet, so that does no count. by the way, i live in india. And I will appreciate any help, just reply even if you think it would not be very helpful, it might just be.
Topic by DrCoolSanta 10 years ago | last reply 3 years ago
Dear all, I m new here, I have some ready circuit using PIC16F series microcontroller chip, I need a simple microcontroller board with software to chage some information on these chip, if RS232 or USB no problem. advance thanks 2 all. khossanr(at)yahoo(dot)com
Topic by khossanr 9 years ago
I am doing a surveillance camera project. I need ARM7 TDMI based microcontroller that supports 1) UART, SPI, USB Interface 2) Ethernet, External Memory Interface â 16 MB SDRAM, 2MB Flash 3) Packaging option other than BGA type Please recommend a suitable microcontroller or a combination to implement this project in a cost effective manner.
Topic by GEORGE NEIL 11 years ago
Hi ... can this microcontroller uk.farnell.com/atmel/atmega328p-mu/mcu-8bit-avr-32k-flash-32qfn/dp/1748522 be used to create "ARDUINO" ??? There seems to be a small difference in the pins in compare to uk.farnell.com/atmel/atmega328p-pu/mcu-8bit-avr-32k-flash-28pdip/dp/1715487 - that's what's making me confused. Thank you in advance for your answers. Zholy
Question by zholy 9 years ago | last reply 8 years ago
Hello! I am looking for a bit of guidance as I have limited knowledge in programming Microcontrollers...amateur experience covers a bit of Arduino and LabVIEW (mostly). My goal is to have an LCD display (Module size +- 65 x 40 mm, with SPI or I2C Comms, Monochromatic) to display small error message/codes and other information as for example temperature, speed, Test number and Timer. I do not know what would be the best Microcontroller to use that is off the shelf, that will still be in production for years to come and is "less complicated" to learn...from what I have read, perhaps the best microcontroller might be the Atmel just don't know what model (am open to other suggestions) Also there shall be 20 push buttons connected to the microcontroller. All that the microcontroller does is read the buttons as a byte and send it to another controller and receive information from that controller to know what information to display on the LCD. It shall also inform the controller of any error that it is experiencing. I do hope that I am providing with clear and enough information so that someone could point me in the right direction. Thank you in advance.
Topic by Art_Rob 1 year ago | last reply 1 year ago
Hi everyone, im new here. i have a school project, i need to build a barcode scanner with microcontroller to use it like ( personnel pointing system ). so i can read each code bar and shows me in a LCD the name of the correspondant Person. thanks for your help
Topic by ael mehdi 6 years ago | last reply 4 years ago
I'm wanting to program and do stuff with LED. Overall I like to make one of those 3x3x3 cube or bigger. I was wondering since I don't have any kind of microcontroller programmer what should I get to start off. I was told to get USBtinyISP. Didn't know if I would be able to do something like this with that or not. http://www.ladyada.net/make/usbtinyisp/ this is the site with it. I just need somewhere to start then I can add on to this to end up making a multiplex or charlieplex cube. Thanks
Topic by Demonic_Crow 10 years ago | last reply 10 years ago
Dear user, I need YOUR help in order to get some insight into the substance of microcontrollers and physical computing. The basic question that needs to be answered is, what the problems are that occur in the process of physical prototyping, what the reasons for these problems are, and how these problems can be avoided. The results will be used in a bachelor thesis, that deals with this topic, trying to find out how easy - or difficult - it is to enter that particular field. I kindly ask you to follow the following link and to participate at this survey. http://www.kwiksurveys.com?s=NJDNHK_210fb8e2 Thank you very much in advance! Vletsou Ioanna LMU - University of Munich
Topic by asking-student 7 years ago | last reply 7 years ago
Hear ye, hear ye! We will be starting a microcontroller contest on January 17. It will be a relatively short contest (3-4 weeks long). So, if you're working on something, wait until then to publish. If you weren't, maybe now is the time to try out an Arduino or any other microcontroller. More info next week. UPDATE: We have partnered with SparkFun for the contest! We will be giving away: 3 First Prizes - $250 worth of goods from SparkFun + laser-etched Leatherman Squirt E4 + Prize Pack 5 Second Prizes - $50 worth of goods from SparkFun + laser-etched Leatherman Squirt E4 + Prize Pack 5 Runners-Up Prizes - laser-etched Leatherman Squirt E4 + Prize Pack UPDATE 2: The contest is now live. See it here.
Topic by fungus amungus 8 years ago | last reply 8 years ago
Hello, anyone here know how to use Nuvoton NUC 140 VE3CN? I get some trouble on connecting the pin and using what kind of library to activate the pin. We already success in compose the main.c but the data can not show in the LCD. I got text like this: warning: unknown conversion type character 0x20 in format [-Wformat=] Thank you in advance
Topic by diah ajengS1 3 years ago
I am about to start programming AVR microcontrollers with a USBtinyISP programmer from http://www.ladyada.net/make/usbtinyisp/. The problem is the computer I use is running vista, and the fact that it is 64 bit doesn't make it any better. I tried WinAVR but it didn't seem to be working properly. I happen to have a bootable linux CD, so mayby that could be used with my computer.Should I run linux or can I find some other software that will work with 64 bit vista? What software should I use to program it? Please explain in detail.
Question by dark sponge 9 years ago | last reply 9 years ago
I have a device with a lever-style switch, like the bottom switch in the picture of this article. http://en.wikipedia.org/wiki/Miniature_snap-action_switch With some multimeter probing, i found that of the three pins, the middle is unconnected. The left pin is always connected to ground. The right pin is connected to ground when the switch is unpressed. When the switch is pressed, the right pin is unconnected. How can I use a microcontroller to stand in for this switch? I'd like to have it activate the switch every 2 seconds. I have the software done, and just need to get the hardware set up. Help is apreciated.
Question by 4lifenerdfighter 6 years ago | last reply 6 years ago