I always had this question in my mind.  Was the cinderblock designed to breathe?  In other words do we want the moisture to go from one side to the other in case of cinderblock walls (say in the basement walls?)  Logically, I would think that the answer is that we want to prevent the moisture to go from one side to the other.  If that is the case, why the cinderblock makers do not make waterproof cinderblocks by adding water proofing chemicals during the manufacturing process? I would greatly appreciate your insights on this subject.

Is Latex paint in the USA the same as acrylic paint here in the UK or is it what the UK call emulation paint for painting walls?

No, not art paint, like the term everybody uses. "This can be done with Paint." What is that? Maybe Ms paint? I don't know THAT either!

Hey if I painted some plastic with carft paint then after a few coats of that I put a clear coat of krylon paint will it  peal or rub of any time soon after I painted it like that?

It seems like the Paint It! Contest has been stuck in judging for a while now. I was wondering when the winners will be announced. Also, (I may have imagined this) weren't there "runner up" prizes initially available in the contest? https://www.instructables.com/contest/paint/

Do any of you have experience with conductive paint? does it have much resistance?  i'm thinkin of heating car windsheild in much the same way that the rear window is done.  i've cracked 1 or windsheilds while defrosting. seems thermal shock from heat vents on dash are too much. just got a new windsheild.  don't want to break it.

I've taken a small school desk and I'm trying to fix it up a bit. The table top is made of wood, but is overlaid with a thick piece of laminate. I've sanded the surface to take out the texture and markings.  I would like to give the laminate it a new paint job, but don't really know what kind of spray paint I should use. Ideas? Suggestions? I could sit here and look it up on Google, but I thought I'd try making a forum and see how it goes. 

 Sanding? What type of paint? How many coats? What type of lacquer? How many coats? Polishing?

What kind of paint brush do you use i use all of them. i use the pencil for editing Pokemon sprites.

Dear Instructables, I tried to enter my instruct able called paint paper, but every time I reloaded the page, it wasn't there. I published I tried unblushing and republishing in the contest. But, it just published it as a normal instrctable. I then tried pressing the enter button, and check marking entered. It wold say I'm entered, but hours later nothing would pop up. I have been at this for several days. But, I haven't been successful. Can you please help me? sincerely, Geremy Mama

I've got some wood that I'd like to paint over, but it's currently got a fair bit of paint on it. The current paint is in fairly good shape and is just a little dirty. The problem is that the paint doesn't run all the way to the edges of the wood and cuts short about 3 cm from the edge of the wood. The paint is also peeling towards the edges. The reverse side of the wood has a few crevices running along it(kind of looks like a turtle shell) as well as a few peg holes. My plan is to sand the front all over and try and smooth the edges of the paint where the paint is peeling. For the other side, I'm going to fill in the crevices and holes with wood putty and then sand over as well. Afterwords, I'll probably apply some dual paint/primer spray paint on top to give it a smooth finish. Now, I have a few questions: 1. Will the peeling edges be a problem when I paint over the wood? 2. Since the crevices are fairly shallow and smooth out pretty easily, will wood putty be a good choice for filling them? 3. Any problems with using a dual paint/primer? Or would it be better to use a separate primer and then paint? I've never really painted anything, and this is pretty much the first real craft project I'm working on, so any advice would be great. If you think it might be a better idea to remove the paint, any ideas you have on how to do it would be great too. I've attached some pictures from various angles. You can probably guess what I'm going to be making :). Thanks.

How do you do a good paint job on your bike? What paint do I get? should I sand it down or Just put primer on it?

I am trying to make a death ray with a parabolic mirror. I have tried a mylar space blanket but it wasn't smooth/reflective enough to make a concentrated beam that burnt anthing. I was wondering if there was any such thing as mirror paint. by this I mean a highly reflective paint. If anybody knows about this or has any other reflective ideas I would apreciate it. Thanks.

What color scheme should I choose for the AK-47 I'm making? Any suggestions? The original colors would be like a burnt sienna and a black I usually spray paint the parts separately here is a pic of the completed model i'm building

Hey, my friend just sold me a bmx frame to me for a good price, but the paint is old and its rusty. I sort of have an idea of how to paint it; sand it, wash it, dry it, prime it, then paint it. however, that's just my guess as to how it would be done. camn anyone suggest some things that i should or should not do? thanks.

Hey guys, I have an older lawn mower that I want to paint the handlebars, wheel rims, and some plastic pieces blaze orange. It's a gift for my girlfriends little brother who's birthday is in a couple weeks. I was wondering what paint I should use for it? I don't have a lot of money to play with so that is definitely a factor. I have a home depot, lowes, value home, and sears near where I live. Thanks for any help!

My bathroom paint is cracking and peeling. We are going to repaint it, but don't want the same issue. What kind of paint should we use

I want to paint a dining room floor. Has anyone ever painted a floor, the wood work is dark, any ideas?

I tried painting a black cloth jacket with white acrylic paint. I painted two layers of paint on it, which I thought would be enough, but later, it started to fade. And after a wash, it was a pure disaster. So I am planning on painting another jacket, so this time, I want it to be perfect. Any tips to preserve the design, or how to paint it, blah blah??? Thanks a load (if help shows up). PS I ve added a pic of my jackets current condition

How can I play mario paint on the snemulds DS emulator using the touch screen?

I'm painting some 1/16" plates of aluminium black. I gave them a wipe down, and used some generic primer and black spray paint. (I originally started off with a paint gun, but it broke). As the plate dries, it starts to crackle in some areas, but not all over. Any ideas what is going on? I've never had this problem painting steel, or wood. Do I need a different type of primer, specifically for aluminium?

We'll I am about to make an instructable on painting and sewing with a leather jacket, my problem is I went to the art store and they did not have acrylic based paint markers, they only had oil based, the worker said that oil based would work fine but I am skeptical, Will oil based pain tmarkers work on leather?

Is it o.k. just to sand a bike, with light grain sandpaper (so as not to scratch) to paint the bike?  I am paining from almost "white" colore to a darker colore.  Any help, sure would be appreciated.  Dorm7guard

When and how is the best way to graffiti non- legal areas without the law catching you?

Flat ceiling i want to paint the ceiling using metallic paint and i do not want roller marks

Ive painted a tshirt with poster paint, it looks good now but will inevitably run. is there anything i can do to seal it? i only really need it for one night. thanks

Is the water based acrylic paint my car is painted with essentially the same as the artist acrylic paint I paint pictures with?

Here you can look up paint recycle centers in your area and get contact info. Please recycle!http://www.managemyhome.com/mmh/bundles/paint

I'm hoping someone here knows something about spray paint. Specifically why some spray paints seem to take forever and a day to dry. In the attached picture the paint on the left (Metallic) dried quickly, within about 45 minutes whereas the paint on the right (Gloss Protective Enamel) is still so wet at 24 hours that I can scratch it with my thumb nail. FYI, I used both paints, one right after the other, on the same kind of metal. So if someone could let me know why some paints dry slower than others and which kind of paints to avoid if I'm in any sort or a rush I would be most appreciative. Thanks

I have a little cap gun, and i was wondering if its possible to spray paint, because if i were making a video, orange and green are ot so realistic

Hey has anybody got a good idea for a longboard paint job?

I am trying to bring back the pink quality of several Yard flamingos.  I know I could buy new ones, but certain people would rather keep for sentimental reasons, so I am trying to restore them.  My problem is when they are painted, after a period of time it chips off, I believe it is because the paint cannot deal with the flamingo plastic swell and shrink of the heat of the day and the coolness of the night.  Any ideas to extend the paint's life, would be appreciated.

I needed to change the colour of a pair of synthetic upper boots for a costume party, and this what I did. Firstly, I used spray paint. Even though I had sanded the surface, the paint would not adhere. In desparation I then used cheap acyrlic paint. Did the job superbly. The only problem is that acyrlic paint dries flat (no shine) but luckily my DH had Gloss Medium in paint box.

I work in a child care with preschool aged children.  We just got a massive donation of powdered tempra paint. I was wondering if there was any interesting craft ideas that we could use other than 1. add water 2. paint with brush Other than using tempra powder to make sidewalk chalk I have been coming up with a blank.  Any new/creative ideas for this product?

Those of you who may have had the occasion to paint a 3D print I'm curious what products and techniques you may have used. I've used one of the Customizer Things to make some name tags and I'd like to paint the raised letters to help them stand out. Any suggestions or methods that work on ABS? Curt

I am not in to paint jobs but really love to do good work and i know if some one gide me good i do very good job from my heart. need little info i want to paint my car rear quarter pannel there is little rust which need to be fix.and i have sanded the quarter pannel the silver body is show now i like to know after fixing the rust what step do i need to take?put filler or first spray with the epoxy primer to wont get rust then filler?and after spraying final paint do i need to sand the paint before clear coate or after final paint do i spray the clear coate straight away?

I'm making a cardboard helmet for my Halloween costume (King Leonidas from 300), and I've run into a dilemma.First of all, I'd like to know if spray paint would stick to car body filler (Bondo), and second, I'd like to know what paints and primers to use to make my helmet look like tarnished metal.Can anybody help? I'm trying to make it look like the helmet in this album.

Hey guys, I've never really done any crafts so im not sure how to go about doing this so i figured id bring it up here. I know i'm 8 months early but I wanted to get started now, on a project for halloween. I randomly decided a few weeks ago i was visited by never good "good idea fairy" and i listened when i was told to by a unicycle by my awesome mind. Then I started riding it, realizing that i could probably get pretty decent at it pretty quickly. Then someone talked about halloween and I was thinking about what would be off the wall so i immediately though of the unicycle. Here, my mind went to steampunk, then it went to looking like abe lincoln while riding a unicycle. Then I realized that my boring chrome painted unicycle would hardly look Victorian, and that it would need a facelift. LONG STORY SHORT: My issue is that I would like to spray paint it a brassy colour, and not ruin the unicycle. I just got back from the craft store, where they told me that my idea of wrapping saran wrap tightly around it would not work because the paint would just run off. They suggested wrapping canvas around it, but when they showed me the cost of canvas i let out a faint hearted laugh and said what if i were to wrap it in a paper or construction paper type  material and paint that, but they turned that down because of the appearance it would give.  But again, it is halloween and it wont be all that light out so I dont really see a huge requirement for detail. Is there any way you guys could think of that will not ruin the unicycle?

Well my mom decided that she would give me permission to paint my room how I wanted. I had an idea of like... a silhouette of a NYC skyline (or any skyline) in black around the walls that goes about 3 or 4 feet up. Then above that would be like... a bluish color. Then in the top corner above my bed, a Orange circle sun were the vertex of the ceiling and 2 walls would be the center of the circle.So first I need to find a silhouette, preferribly just black buildings, kinda like this, but less complicated. Something easily taped off.link to pictureAlso, I want you suggestions on the paint colors. I'm pretty set on black for the buildings but I'm not sure about the sky/sun.Comments/Suggestions/Concerns/Help

Yesterday i spraypainted faux leather. it looks good and everything, but it wont dry. i spraypainted it yesterday morning and its still really sticky. what did i do wrong? what can i do to fix it?

Hi folks. I have been given a Gladding Float-Pac inflatable dinghy that has been left out in the weather a bit too long & the surface of both the orange & green rubber has become stained from fallen leaves. I have had a look around the interweb & have found a couple of paints suitable for inflatables but to tell the truth they are a bit expensive just to smarten up a boat that will seldom get used particularly as I would have to buy two colours. The boat is in otherwise good condition with no holes or punctures & there is no scuffing or fabric showing through so finishes like Tuff-coat wold be a bit over the top. Does anybody have any suggestion for a pait that would be flexible enough for the job, i'm not really too worried about the colours although the original green & orange would be nice to keep. Thanks in advance for your suggestions folks.

I was painting my Nerf gun using Rustoleum spray paint. All went well and I let it dry for a week (yes, it says 1 hour but I was too busy for a week). Then I decided to put a Matte Clear Coat from Rustoleum and the paint started bubbling up. The clear coat did not bubble but the other paints did! And what's weird is that it only bubbled in certain areas. What happened and what's the solution?

Stenciling

Five minute of fun with windows paint! I hope you like it!

I've found some glow in the dark paint, which I'm going to use to paint my bike frame. The problem is that its brush-on not spray paint. I really want a glow in the dark frame, and I can't find any glow in the dark spray paint. All the bike painting instructables use spray paint. Does anyone have some tips on how to do a good job with a brush?

I bought a painting at a thrift store. It appears to be palette-applied oil paint. There are no brush strokes that I can see. It looks like it was painted on plywood. It's pretty dirty. And it looks kind of old. There's no frame.

I want to pep up these shoes. So my idea was to paint them, so can anyone tell me how to paint it, what paint to use and suggest colors and designs. And will the paint stay after rough use (playing basketball) and wash? Any way to make it permanent? Thx in advance.

My guitar that me and my friend painted:) So now I`ve got a unique guitar

Hi my name is mullerjeanfrancois I do art,If you interested in any piece please let me know.I hope you enjoy my Art I am an artist who works in many different types of media; oil, acrylic, abstract paintings on canvas, at http://www.artistpaintingonline.com