Is it possible to put a straight bend in a perspex sheet?

I want to put a sheet of perspex  on the back of a shower cubicle on an inside corner without joining it at the corner Is it possible to bend a sheet of perspex at a 45% angle

Question by Mopsyben   |  last reply


How do i project onto perspex?

 Hi folks, about to embark on an art project where i am aiming to project type onto perspex, any ideas?

Question by sharon.lay 



Does anyone know a way to sense the temperature of perspex sheet?

I have a project in which I need to know the temperature of the perspex in a perspex sheet (so I can control aforesaid temperature). The Temperature sensors I know (TMP35-TO92) are okay for getting atmospheric temperature but no good for this.Has anyone a solution to the problem?Thanks

Topic by vagulus   |  last reply


Can a hot wire cutter be used to cut shapes in acrylic or perspex?

Is there a tool that's relatively cheap to buy, that I can use at home to cut clean shapes from acrylic, perspex, rubber, thin sheeted wood (any of the above)? I'm thinking of a similar finish (although obviously a bit less pristine) to that produced by a laser cutter. Thanks!

Question by alicecc_21   |  last reply


Making translucent, glowing cubes. Best shell material choice?

I'm making eight, seamless 15 cm3 cubes that will be translucent and have a glossy finish. They will be lit up (with LEDs, etc.) so the entire cube appears to glow, but there is a base side which will always be on the bottom (it doesn't have to be made of this material.) Sturdiness is desired (they will be in transit at some point), as well as low cost. The solutions I have in mind at this point are: Frosted acrylic/perspex glued together Some form of cloudy resin cast into a single-piece shell I imagine that the resin would have a better overall appearance if it goes well, but it sounds expensive and complicated. The perspex solution may have a less appealing end result due to the edges between each face. Please suggest alternate solutions if you can think of some! Thanks for your help. TK.

Question by T-K   |  last reply


How do I make an illuminated perspex sheet for a Mazda MX5 Mk1 (Uk)?

Basically I want to replace the windblocker with clear perspex sheet with a word cut out and when I brake the letters are illuminated in red but also have the option to leave the light on but illuminated blue. Any Ideas? I'm a newbie re wiring and leds, not stupid but as simple as possible please. TIA

Question by darkan9el   |  last reply


How can I make my own deep propagator top, please? Answered

Essentially I can't afford those big, deep propagators - and if I could I wouldn't pay the extortionate prices. I can get a deep bucket to house the hydroponics 'ible found on this site, but I can't find tall, clear propagator tops to protect/house the tender cuttings I want to take (basically of foodstuffs). If you can think of a Rubbermaid style storage box/bucket, I would ideally like to make a clear top about 12 inches high that also fits tightly against the Rubbermaid box. My thoughts initially are making a plexi-glass/perspex box top - any further thoughts would be very much appreciated. Thanks for stopping by.

Question by kevinhannan   |  last reply


LCD/VFD free samples?

These screens are pretty expensive, has anyone been successful at recieving a sample? Also if anyone knows where I can get samples of flux, desoldering braid, perspex, rare-earth magnets, IC sockets and headers. Thanks, Alex.

Topic by alexgeek   |  last reply


Would someone identify the symbols/pictograms in the attached image? Answered

I found this on the wall by the bar in a UK pub. It looks old, I don't know what it means, but I thought this would get me an answer. It looks like fret-sawn perspex, could be a school project perhaps. L

Question by lemonie   |  last reply


Find/make frosted glass/plastic tubing

I'm building an audio vu meter, and thought the LEDs would look nice enclosed in some frosted tubing, but I'm having trouble finding any. Something like a fluorescent tube would be perfect, but the coating on the inside of them rubs off fairly easily (is it phosphorous based?), and cutting these things open isn't usually recommended (they have small quantities of mercury in, I believe). It's easy enough to find perspex tubing on ebay, but it's all clear - I really want something translucent, so that the LEDs give a glow of light, rather than a point. Is there something I can coat glass or perspex with to create this effect? Or am I searching for the wrong words? I sometimes see the fluorescent tubes referred to having a satin finish, but that hasn't helped

Topic by psmith37   |  last reply


how much weight can a large L-shape wall bracket support?

I want to build a desk using L shape brackets and a Large piece of wood. or perspex. Now how much weight can each of these brackets support and how many should I use If euipment I have weighs around 10 - 20 kilogramms. 

Question by enoted   |  last reply


Secure method to attach a phone to wall or floor?

I would like to figure out an inexpensive and discreet way to attach a smartphone to the wall or floor (not directly - slightly set apart with e.g a rod or a lead), in a way that it is secure, and can't be easily stolen. The phone will be used as a display screen and will be resting on top of something, so needs to be relatively manouvreable. I have access to a laser cutter / clear perspex / workshop tools / ebay.

Question by CassiaD   |  last reply


asus eepc tablet conversion parts sourcing?

I have an eepc 1005pe laptop, and i need a screen and a touch screen panel with controller, to make it in to a tablet any suggestions where to get the parts? also what would be the easiest way to do it, i dont have the screen case, so i was wondering if perspex cut and bent to fit around the touch screen and lcd would work

Question by The nerdling   |  last reply


any good ideas for a free standing portable and easy to store away laptop stand/holder/desk??

Any good ideas for a free standing portable and easy to store away laptop stand/holder/desk??if possible give me simple but creative ideas for this project. it is for my junior cert. it has to be made from wood and if u wanted to you could add in glass, aluminium, perspex etc. please reply a.s.a.p..thanks for reading.!

Question by JPB981   |  last reply


help, where to start please? 20*20*20cm fridge

Hello, First post, please be nice =) I unfortunately know absolutely nothing about electronics, or soldering... you get the idea. Clueless. But, I need to make a 20*20*20cm fridge out of perspex (something to do with my photography, see http://www.flickr.com/photos/jingleslenobel/ I gather that a Peltier with heat sink might do it? Would anyone be able to point me in the right direction please, in terms of making such a thing? Many thanks

Topic by ingleslenobel   |  last reply


How to backlight outdoor metal wall art? Answered

My friend is buying a piece of wall art (around 1.2m x .8m) which is an image of a bird (I have not seen it yet, but lets say it looked like the attached image, it is metal, flat. It is going to be hung outside and they would like it to be backlit, so it is visible at night.  They were quoted $130 for a perspex sheet with LED lighting, which seems steep to me, there should be a cheaper way to do it DIY. Any suggestions. Scott

Question by silliou   |  last reply


LED Light Box Help!

Hey, I am very new to crafting things using LED's and stuff, but I want to get in to it, and have set myself a project as I need a lightbox for drawing/tracing for work. I want to make a A3 (29mm7 × 420 mm) sized box, with the aim to keep it as slim as possible. So I know that I need to use LED's because they are small and bright, I have been looking at white ones. I also know that I need some sort of frosted perspex to diffuse the light and keep the coverage of light even. That is important. A switch is necessary too of course! However I know nothing about what I need to connect the LED's together and how I am to power this. I would prefer to power this with power, but don't know how viable this is with LED's. I would just like a bit of advice of what I actually need then I will probably be able to figure the rest out!  Oh also if could keep the cost under £40 that would be perfect because if it was more, I might aswell just buy one from the shop! Cheers! Will 

Topic by Will172 


LED Light Box Help!

Hey, I am very new to crafting things using LED's and stuff, but I want to get in to it, and have set myself a project as I need a lightbox for drawing/tracing for work. I want to make a A3 (29mm7 × 420 mm) sized box, with the aim to keep it as slim as possible. So I know that I need to use LED's because they are small and bright, I have been looking at white ones. I also know that I need some sort of frosted perspex to diffuse the light and keep the coverage of light even. That is important. A switch is necessary too of course! However I know nothing about what I need to connect the LED's together and how I am to power this. I would prefer to power this with power, but don't know how viable this is with LED's. I would just like a bit of advice of what I actually need then I will probably be able to figure the rest out! Oh also if could keep the cost under £40 that would be perfect because if it was more, I might aswell just buy one from the shop! Cheers! Will

Topic by Will172   |  last reply


Led light & switch

Hi, I've purchased a wooden toy kitchen, for my daughter. I want to add a couple of special effects to it, for realism. There's one part I don't know exactly how to do and I don't know the correct terminology for the parts I need. So any advice would be greatly appreciated. basically, the pretend oven part of the kitchen, I'd like to add a push to make, illuminated switch to the panel that houses the pretend dials. I want this switch to be connected to a battery, hidden inside the play oven & upon pressing it, not only does the switch itself light up, it powers some red led lights. This is so when my daughter presses the button, it'll light up red inside, to give the impression it's hot, the oven has a Perspex panel, so the red light will be noticeable. I'm unsure how many led lights I'd need, it's probably 1 cubic foot in volume & doesn't need to be overly bright. So what type of push button switch, what types of LED & how many, what batteries and what other components would I need?   Sorry for the lack of knowledge & thanks for any advice.

Topic by dlee60   |  last reply


Tablet PC From Netbook? Answered

Hello Everyone :) I'm new to this community, though I'm not new to DIY projects. I hope somebody can help me out, I need some help with a proposed project of mine.  I have an old Acer Aspire one 751h and it's an 11.6 inch netbook, LED screen, and I'm willing to tear it down to make a windows tablet. I know I need a touch screen kit, but I need help choosing one, I don't mind resistive ( I know it's very hard to find a multi touch 11.6 inch touch screen kit) In fact, I would say I would prefer ressistive as It's cheaper. One more thing, is it possible to use a larger touchscreen on a smaller screen and then calibrate it? as long as it's the same aspect ratio? For the tablet case/ body, inverting the screen and using the original Acer aspire one 751h case isn't hard, but if it's possible to use perspex or a material like that ( no carbon fibre please) I would like a few pointers. I don't mind the tablet having a rectangular feel/ look, as long as it's easy and practical to build. I also have an old  8x6 inch graphics tablet with 1024 levels of sensitivity, is there any way I can use this along with the touchsreen for input? Like behind the screen.  The netbook runs Full HD content and windows 7 fine and has a 16:9 aspect ratio screen, one of the reasons I'm keen on the project . Thanks a lot ! :) 

Question by Nimer11   |  last reply


LED display to an Audio Click? Visual click track aid for drummers required.

Hi Folks, I'm searching for some info on how to make a visual "Click track" aid. In one of my bands, we use a click track on some tracks and live on others. I use a single in ear monitor for the click track which s fine for most tracks, but for some, I need the click fairly loud and this cannot be good for the old lugs long-term. So, I want to make a small LED display or two that can react to an audio signal that is fed from the click track channel. I've seen many instructables that show how to make LED blink/flash etc to music, but my requirements are a little different (I think). The click at the beginning of each bar is higher in pitch and has a higher velocity compared to the other click in that bar, so for example; Playing in 4/4 time signature: click 1 - Velocity =100 - pitch C5 click 2 - Velocity =90 - pitch C4 click 3 - Velocity =90 - pitch C4 click 4 - Velocity =90 - pitch C4 If playing in another time signatures ie; 3/4 or 6/8, then I would also need to cater for this in the display Questions: 1. Does anyone know how I could devise a system that would light a Red led for beat 1 and then perhaps a white (or other colour) led for the rest of the beats, but in a sequential fashion? 1,2,3,4. 2. Is it possible to change which led flashes based on either pitch or velocity? I could even make the front of the led display show actual numbers over a perspex cover so at anytime, a quick glance will show me exactly where I am in the bar. So rather than coloured leds. So to recap, I'd like to be able to take an additional audio feed from the click track channel from a mixer, into this new "drummers visual click track aid" device and have it react to the clicktrack and display that in the form of beats per bar based on either pitch or velocity of the click track. I currently use a couple of wood block sounds for the click track because they are very clean and short. Many thanks for taking the time to read through my requests and if you're the kind of clever person who could make such a device, I'd be more than happy to pay you for your input and suggestions. Many thanks in advance and I look forward to hearing from you soon. Cheers Phill

Topic by CrashCourseMuso