AIRSOFT PVC BIPOD With LASER

18,003

8

114

Intro: AIRSOFT PVC BIPOD With LASER

ADD TO YOUR airsoft assault rifles or rifles! It provides support to your gun giving it better accuracy ! this will only cost a dollar or two unless you don't have a laser pointer then its about 5 dollars!!'

Step 1: WHAT YOU NEED!

WHAT YOU NEED:

Hot glue
1 1/2in PVC peice (5 in. long)
2 of the same size PVC peices
laser pointer
duct tape
Airsoft rifle'

Step 2: Put the Two Peices Together on the 5 In.

Now take the 2 same sized PVC peices and glue them to the 5in. peice of PVC!'

Step 3: Assemble the Laser!

Now make sure the laser pointer fits in the PVC tube tightly!

Allow it to stick out !

To turn on the laser put a peice of duct tape over the button!'

Step 4: Assembly!

Now to put on the bipod with laser!

Now tape the bipod to the gun!

Put alot of tape on so it want come off and want move!!

Turn the laser on !!

And there you go you have a support on you gun !'

NOW YOUR GUN IS DONE HAVE FUN !! DONT FORGET TO PUT EYE PROTECTION ON !!'

Share

    Recommendations

    • Optics Contest

      Optics Contest
    • Plastics Contest

      Plastics Contest
    • Electronics Tips & Tricks Challenge

      Electronics Tips & Tricks Challenge

    114 Discussions

    0
    None
    qwop

    7 years ago on Introduction

    lol I was looking this up for this exact same gun

    0
    None
    arb1ter

    8 years ago on Step 1

     AAAAhhhhh Duct tape. No surprise that it is used in about 60% of instructables

    0
    None

    to solve other peoples problems of you bi pod (which is great) paint it black or camo to make it look better and use Tridon Rings instead of Duct Tape other than that good instructable.

    tridon%20hose%20clips.jpg
    0
    None
    Misomalu

    9 years ago on Introduction

    O.K. first off nice try but i would never take that gun to actually play airsoft from what iv heard its gravity fed not good for actual use the bipod is good for playing with your friends (which i hope is all you are doing with it no offense but you would look really stupid playing airsoft with a pvc bipod) but buying a real one off a website (assuming you are American is really cheap) www.airsoftgi.com, http://www.realistictoyguns.com/ both great sites cheap stuff and cheap guns (assuming you are Canadian) www.007airsoft.com, www.buyairsoft.ca, and velocity arms(possibly) are good yet again no offense just constructive criticism.

    The stupid laser on the bipod is ridiculous. It would be impossible to zero that it. That "scope that came with the gun" is a red dot, not a scope... Instead of making your peashooter look like a ducttape wallet, you should make a version that uses bolts and such. Real bipods are collapsible and foldable.

    1 reply
    0
    None
    spike2271

    9 years ago on Introduction

    just my opinion I think the duct tape looks bad. I have already taken a shirt green and cut it up long story short made ghillie wrap for it I'm going to paint the bipod green and black and then use some extra pieces of shirt to tie it on and still have it hanging of like rags it would look really good hope someone else tries my idea

    0
    None
    dla888

    9 years ago on Introduction

    Maybe a tripod? Perhaps you could take a three way elbow pipe fitting and drill a hole on top and put in a clamp to hold the barrel stock, whatever.

    0
    None
    marshman19

    10 years ago on Introduction

    if you could clamp on the pvc wouldn't it work better because it's removeable? and if you had two different sizes u could make telescoping legs

    0
    None

    hmm. mabe a molded plastic 1 would b better :-\? Also, lol i got that gun, it was my first airsoft gun, also it was the crappiest one ever :-P the scope is the freakin' magazine lol! Iv grown up in airsofting, i got that gun (crappy), a Boyi M16 w Grenade Launcher, and my new babe JG M4 S-System (SCAR) it shoots 400fps with .20 gram bbs Stock!

    2 replies
    0
    None

    I use an A&K S-System, it is pretty accurate, It can hit a starbuck's mint tin from around 30 ft away. Unless A&K is the same as Jing Gong.....

    0
    None

    Ya, the real diff from a JG and A&K S-System is A&K uses a M100 or mabe a M110 spring, (about 330-345fps .20), and a JG uses a M120 spring (400-440 FPS .20), and in the JG the gearbox is claimed to be like one of the best v2 gearboxes (it is greatly airtight), and the gears are claimed to be better than Classic Army gears. Well in my JG S-System i can put a clean hole in a Super-Jumbo Altoids gift tin from about 50 feet away (.20g bb) witch the tin is oh mabe as thick as a pop cans to rim (thick ;-). but other than internals the JG and A&K is really the same pretty much.