David 3D Scanner ...Or Not.

104,767

192

1

Intro: David 3D Scanner ...Or Not.

Here's how you can get to make some .obj files out of real life objects.

What you need:

-An 8$ Laser Edge form any Hardware Store;
-The David scanner program, from
David 3D Scanner


Or, since David is generating a lot of complaints from the Readers of this Instructable, use one of these 5:

http://makezine.com/2015/01/15/5-diy-3d-scanners-to-watch/


-.Net Framework add-on from Microsoft, if you don't have it installed already;
.Net Framework
-A webcam;
-Some printed patterns
-And stuff you'll find around you house, like Styrofoam boards, and UHU Por to glue it, for
example.
If you don't like to change the Edge's batteries all the time, better add a Tranformer with 3V
output, a common Mono plug, and some soldering work, too.
Note:
For an easy scan, and good results, you better have an Airbrush around, to cover the
objects with a wash-away layer of white paint, common Gouache will do fine.

Baby powder is said to give good results on stuff you don't want to paint.

This other Instructable shows you how to make a neat laserline, so have a look at it, too:

https://www.instructables.com/id/-The-DIY-Laserline-/

Step 1: Download

Right, you better start with the program, download it from http://www.cs.tubs.de/rob/david.htm , click on the links on the intro, comes with a complete manual, just double-click on the program, or click Help anytime.´

And, if you're not into recieving Window's updates by
the Net, download the .Net Framework add-on from
Microsoft, first.

Step 2: Frame Thang

Then you're off to make a square angled thing where to place the prints you make from the

Calibpoints_Scale60_DIN_A3.pdf or
Calibpoints_Scale60_DIN_A4.pdf,

I went and done a hap-hazzard contraption from a couple of straight
Styrofoam boards I had, and glued a cut Kodak envelope onto it, AFTER I cut and glued the A4 page into it.

See, you can make an half-decent right-angled frame, even if you're a lazy slob!

Step 3: Cardboard Gluin' Fool

Get some cardboard, you're in business!
Of course, for an A3 thing, you need to do things a little mode decent!
Maybe Acrilic glass, so there's no excuse for crappy scans!

Step 4: Dismantling Stuff! Yeah!

Then I disassembled the Laser Edge, after getting annoyed with changing batteries, got a Mono plug from junk I keep, wired it to the Red and Black wires, and it's now only a question of pluging the thing to a Multi-Voltage Power Supply, and presto!

Allways bright laser light!

Step 5: Re-assembled

Here's the Laser edge assembled, with a few holes on it, too!
After the shot, I added a lateral slot for the thing to stand upright.

Step 6: A Lenzzz!

The egde's lens was bloody useless for 3D scanning, so, after a few other attempts, I settled for an old eyedrop filled with water and sealed with the last failed attempt, a BIC ballpoint pen's transparent body, it's plastic melt away to seal the eyedrop, first sealed at the tip, then fill it with water, then seal the top.

Used the re-usable adherent stuff that comes with the Edge, to fix the eyedrop into the Edge, too.

Here you can see it, cheaper than looking for a
glass rod, I suppose!

Step 7: Scan It!

You got it all, so on to the first scan, mine were complete garbadge, either the objects had dark colours or a shiny surface, or the laser batteries loosed their juice, so I went and done the power plug, and picked a completely dull piece of Roofmate, and scanned it, perfection, for what it's worth, so here's the thing,
then here's the obj file it gave:

Step 8: Obelix, Where Are You?

A dull example; let's see Buzz Lightyear instead, see next step:

Step 9: Buzz Lightyear!

Here's Buzz Lightyear, too much colours, so I've airbrushed white paint on it, see next step

Step 10: Plaster! or Is It?

...and it looks like
plaster, now.

Step 11: Well....Humm...

As you can see, close
but no cigar!
Looks like I've wrapped the thing on Aluminum foil, or the impact marks of Buzz smashing into a metal wall!

Either the webcam's junk, or I'm doing soemething wrong, but as far as showing the program works, it does, so next thing I'll make
the A3 version, and see if that changes anything.

Remember, my webcam's a crappy old Mustek 300 A, so if you've got something better, and a PC to handle it, go for it!

Share

    Recommendations

    • Metalworking Contest

      Metalworking Contest
    • Tiny Home Contest

      Tiny Home Contest
    • Fix It! Contest

      Fix It! Contest

    Discussions

    0
    None
    AnnieK32

    Question 4 months ago on Step 11

    Hello. I don't know if you can help me or not but I am desparate so here we go.
    I'm using david 4, 3d scanner. I'm using the image grabber function. I take pictures of the 48 projected patterns on the calibration panel and let david use them instead of the live view. Apparently it should work perfectly but I get very low scanning quality. The scanned image of the calibration board is missing large parts and has a very bad quality. What am I doing wrong here? I have attached a picture.
    Thank you

    IMG-20180516-WA0003.jpeg