Knex Revolver

Introduction: Knex Revolver

About: Hey everyone, welcome to my Instuctable, or my Instructables page. Well I hope you like what you see and if you do, don't forget to SUBSCRIBE. I like to build just about anything from airsoft guns to fishing l…

This is my first instructable, so lets get started. I got the idea from Spryans gun. I do not take full credit because i kept sum of his ideas including the handle and cylinder. Other than that i believe the design was mine. Read descriptions for each step for clearer instructions.

PROS
Okay range
8 rounds
Iron sights
Strong frame
Pretty accurate
Rounds don't fall out of cylinder

CONS
No true trigger(aaaggggghhh Trust me Ive tried)
If you pull the firing pin to far it will fall out
that's all that i can think of

   Piece Count
   Connectors
   Grey(one side): 23
   Orange(two side): 8
   Light gray(two side): 8
   Purple(three side): 2
   Red(three side): 1
   Green(four side): 5
   Yellow(five side): 8
   Blue(seven side): 4
   White(eight side): 2

   Rods
   Green:21
   White:12
   Blue:4
   Yellow:2
   Red:none
   Grey:3

   Other
   Grey Spacers: 36
   Y clips:5
   Tape (Recommended Duct tape)
   Some rubber bands
   any rod your willing to mod
   Front sight requires these unless you modify:
   A snow flake and 8 blue rods just for the cylinder, you dont need them permanently just for      one step

Step 1: Cylinder

This is the hardest step so lets get it over with. For this step you will need the tape and the white snowflake with blue rods attached. First make 9 of these... then put tape around the SPACERS only.Once you've put tape on all of them put them on the snowflake with blue rods attached. You should be left with one thing of spacers left. Put tape around this until it is snug in-between all of the spacers.After wrap whole thing in tape.

Step 2: Handle


Step 3: Main Frame


Step 4: Barrel


Step 5: Top Barrel


Step 6: Everything Else

Make these

Step 7: Assembly


Be the First to Share

    Recommendations

    • Mason Jar Speed Challenge

      Mason Jar Speed Challenge
    • Pumpkin Challenge

      Pumpkin Challenge
    • Bikes Challenge

      Bikes Challenge

    18 Discussions

    0
    pythonn
    pythonn

    9 years ago on Step 4

    whats your modded piece?

    0
    Mace!
    Mace!

    9 years ago on Introduction

    I don't see any advantage over the original revolver....

    0
    KnexFreak360
    KnexFreak360

    Reply 9 years ago on Introduction

    yes it does the rounds 100% for sure will not jam in the cylinder

    0
    Mace!
    Mace!

    Reply 9 years ago on Introduction

    I made my own version of Sypran's a while back, it was much smaller, much sturdier, the bullets never fell out, and it went farther.

    0
    DJ Radio
    DJ Radio

    9 years ago on Introduction

    I'm sorry, but the design quality here is shoddy, and this does not improve anything over Sypran's revolver.

    0
    KnexFreak360
    KnexFreak360

    Reply 9 years ago on Introduction

    yes it does the rounds 100% for sure will not jam in the cylinder

    0
    slimshaddy
    slimshaddy

    9 years ago on Introduction

    click on this website to find a revolver with true trigger http://www.youtube.com/watch?v=ghs67HFZPrU

    0
    KnexFreak360
    KnexFreak360

    Reply 9 years ago on Introduction

    thanks i was planning to remake and design to make a true trigger but idk when i will

    0
    RMConstruction
    RMConstruction

    Reply 9 years ago on Introduction

    It appears it worked. I laid that trap months ago to see if anybody would catch me out.