Pocket Pen Gun/Launcher

Introduction: Pocket Pen Gun/Launcher

DANGER THIS CAN SHOOT YOUR EYE OUT OR BE LETHAL.
I AM NOT RESPONSIBLE FOR ANY DAMAGE OR INJURY CAUSED! NEVER SHOOT AT THE FACE OR AND ANIMAL!

I will be showing you how to make a Bic Pen gun that shoots 100+ feet and is smaller than your finger

See picture for materials.
only one pen is needed.

!I AM NOT RESPONSIBLE FOR ANY DAMAGE OR INJURY CAUSED! NEVER SHOOT AT THE FACE OR AND ANIMAL!

Step 1: Pen Gun

Take apart the pens. you will no longer need the cap or tube only the ink and tip of the tube. The ink will become ammo. take the pen tube tip off the ink. You will need both parts.

Step 2: Assembly

Take the rubber band and cut it once.

Step 3: Assembly

Put the rubber band on like this, with tape, be shure to pull tape tightly when rapring. Cut extra rubberband off.

Step 4: All Done!

Here you are!

When firing load the back of the pen ink through the barrel of the pen tub tip and pinch the rubber band on the ink, pull back and release..

Step 5: Ranges and Ammo

The Pen Gun will shoot about 100+ feet. Yes I know that sounds scary. When you use a flat rubber band (The best ones in my opinion), a long ink with fletchings (6 or 7 inches, get a long pen form dollar store or fair) it will shoot that far. I shot to about 3 house down from mine.
IF you want to shoot at friends for fun, I recommend to take tape and wrap a thick layer around the tip so it WON'T puncture skin.

Participated in the
Pocket-Sized

Be the First to Share

    Recommendations

    • Exercise Speed Challenge

      Exercise Speed Challenge
    • Pocket-Sized Speed Challenge

      Pocket-Sized Speed Challenge
    • Super-Size Speed Challenge

      Super-Size Speed Challenge

    65 Discussions

    0
    terminatorman
    terminatorman

    12 years ago on Step 3

    sweet instructable, but i don't see how the heck it shoots ink a 100 ft. could you tell me?

    0
    DEEJAY642
    DEEJAY642

    5 years ago on Introduction

    You can also make the ammo out if long skewers and by putting the tips of pens on them

    0
    Jared101
    Jared101

    5 years ago

    Infinite favorites

    0
    Jared101
    Jared101

    5 years ago

    Nicely done

    0
    UberPug
    UberPug

    12 years ago on Introduction

    i made one of these before and if you shoot it hard enough, ink comes out the back.

    0
    maxxxem
    maxxxem

    Reply 12 years ago on Introduction

    wow never done that before but i did have the tip hit the wall and break off and splatering all over.

    0
    THECHINABOY
    THECHINABOY

    9 years ago on Step 5

    THIS IS SO COOL!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!THANK YOU! THANK YOU! THANK YOU! THANK YOU! THANK YOU! THANK YOU!

    0
    thetrevsta
    thetrevsta

    Reply 10 years ago on Introduction

    i had the same problem get some sowing thread and wrap that tightly around the rubber band before taping it that helps alot

    0
    THECHINABOY
    THECHINABOY

    Reply 9 years ago on Step 4

    the thread idea is so good!!!!! thx

    0
    glugnar
    glugnar

    Reply 10 years ago on Step 4

    wrp th tap tightr thn

    0
    dirtnap
    dirtnap

    Reply 10 years ago on Step 4

    lol? English man

    0
    glugnar
    glugnar

    Reply 10 years ago on Step 4

    oh srry i didnt have a lot of time i ment "wrap it tighter then" hope that helps