Steyr AUG A2 Instructions

586

5

36

About: Hey there. I won't add too much info here, as it'll show up as one big paragraph.

Intro: Steyr AUG A2 Instructions

Hello there,

These are the instructions for my Steyr AUG A2 model.
You can find more information about the gun right here.

Step 1: The Stock

This shouldn't be too hard.
I hope the pictures are in the right order, the uploader was being annoying.
If you have any questions, don't be afraid to ask them.

Step 2:

Again, if you need help, ask me.

Step 3: Assembling

The easiest way to do this, is to remove the four green rods on the stock's end. Then just slide the two halves into eachother, and add the rods again.

I hope you enjoy your own AUG A2!

Share

    Recommendations

    • Halloween Contest 2018

      Halloween Contest 2018
    • Fix It! Contest

      Fix It! Contest
    • Audio Contest 2018

      Audio Contest 2018

    36 Discussions

    0
    None
    OfficialKNEXGUY

    2 years ago

    Hey just one quick question. How did you make the mag? Could you post a few pics on how you made it (or at least tell me). Thanks!

    -OfficialKNEXGUY

    1 reply
    0
    None
    dr. richtofenOfficialKNEXGUY

    Reply 2 years ago

    The inner parts are almost the same as the outer walls, just replace the top-most yellow connectors with blue rods. Like in this photo.

    To make it curver, don't fully connect the green rods on one side, as you can see in the photos of this ible.
    Hope this helped~

    0
    None
    JulianD5

    2 years ago

    on my aug I made the magazine kinda like stuck with a blue rod

    1 reply
    0
    None
    dr. richtofenJulianD5

    Reply 2 years ago

    Do you have a picture of you one? If so, post it here! I'd like to see it.
    Sometimes, magazine releases can be stubborn, which can be fixed with a small bump.
    Anyway, I hope you like it, even though the magazine fell out for you sometimes.

    0
    None
    megustatrains

    2 years ago

    is that a pendulum blood sugar pic i see?

    also damn i have been gone for too long... noice wep

    2 replies
    0
    None
    BOSSLIKEDAT99

    2 years ago

    Before I build this, are there cut pieces that are important for the gun to work

    1 reply
    0
    None
    dr. richtofenBOSSLIKEDAT99

    Reply 2 years ago

    There are a few broken white rods in this gun, but none of them should be that important. The ones in the handle can be replaced by normal ones. Tthe broken rod in the magazine can be replaced by green rods in the round connector holes, but you'll need tape to keep them in.
    There are two other ones in step one, which could be replaced as well.
    The orange connector in the magazine release can be a normal one, I just had this broken one laying around.

    I don't have this gun anymore, so if you need help with ways to get around broken pieces, let me know, and I'll rebuild the specific part.

    0
    None
    Kona-chan

    2 years ago

    Instructions weren't clear enough, got tongue stuck in a cow

    1 reply

    Actually that's a bad idea...........a switchblade shooter would be more effective (since guns are illegal....for you)

    0
    None
    CorgiCritterdr. richtofen

    Reply 2 years ago

    Let's not let this get out of hand. I know the knife shooter deal went pretty crazy and I shouldn't have brought it back up. I did have a nice long comment for the slideshow of this, but I never go around to posting it. I do really like the gun, and the instructions are fine. However, the top rail seems a little unfinished.

    No, I haven't been very active, but I have been building. I don't the remember any aggressiveness since the knife shooter deal. I didn't mean to get everyone riled up again, so I'm sorry.

    I will say this, that you do come out seeming kinda aggressive in this. But that's somewhat my fault.

    And yes, I should have handled the knife shooter fiasco differently.

    0
    None
    dr. richtofenCorgiCritter

    Reply 2 years ago

    Eh, everything's fine after a good night of sleep.
    This kind of stuff just happens every so often, why, I don't know.

    I'm sorry as well. I overreacted, and should've stopped after the "ok" comment. But for some reason, I often can't. Again, sorry for taking this so far.

    Thanks for the feedback. Some parts of the gun could've been better, I agree. I just lack the pieces that are needed.¯\_(ツ)_/¯
    Excuses, I know, but yeah.

    As long as we're good at the end of the day, that's fine.
    Let's just leave this mess behind.

    0
    None
    CorgiCritterdr. richtofen

    Reply 2 years ago

    Alright. I'd still like to know what you meant by me being "aggressive" lately though.