AXR AMAR

Hai How did you implement UPI payment to the project ?

Super guru !

Good ...

Voted !

Manglore means ???

Awesome work bro !

Nice :)

Esp8266 is also cheap and easy to program,since it is a wireless device it has great advantage over the Arduino board and this board is not limited to Above Instructable, still lot more to come.

I did that instructable too !

Thank you Brother..

https://www.hackster.io/aXr/pinguino-project-a-pic...pic based arduino

Awesome..!

Superb....

Cool..! it looks like pro

Nice.

very useful,

Thanks for the reply, Already voted brother.!

it's awesome..! Do you have any idea about building a small computer using Nokia display, RTC, EEPROM/SDcard, Arduino, and Buttons .

nice !

https://www.instructables.com/DIY-Tiny-Arduinowi... more about Attiny..!

Awesome..!very usefull

very useful !

You got My vote Bro.., Awesome Work.!

Super...

https://www.instructables.com/Arduino-Just-Clone...

Here is the tutorial to build arduino using PIC microcontroller A.K.A "THE PINGUINO" https://www.instructables.com/Pinguino-Project-a-PIC-Microcontroller-Based-Ardui/

https://www.instructables.com/Pinguino-Project-a-PIC-Microcontroller-Based-Ardui/

Good going ! :)

nice project, I made one :)

wow ! its simple and fun.

Nanna fav thindi :)

I have used arduino pro mini !, you may use any type of arduino.

Yes bro!

Ya..

one vote !

it will recognise prerecorded voice only ! but you can record commands in any language !Use any of these language and have fun :- Punjabi, Kannada, hindi ,Tamil and Telugu. !

cool !

nice project !

https://www.instructables.com/How-to-Blink-an-Led-With-PIC16F886-if you are preparing own board ! go through this ...

ha ha !! Brobut still its a 3 only1)connection2)Bootloading3)Led blinking

You are right !What is a Bootloader?Atmel AVRs are great little ICs, but they can be a bit tricky to program. You need a special programmer and some fancy .hex files, and its not very beginner friendly. The Arduino has largely done away with these issues. They’ve put a .hex file on their AVR chips that allows you to program the board over theserial port, meaning all you need to program your Arduino is a USB cable.The bootloader is basically a .hex file that runs when you turn on the board. It is very similar to the BIOSthat runs on your PC. It does two things. First, it looks around to see if the computer is trying to program it. If it is, it grabs the program from the computer and uploads it into the ICs memory (in a specific location so as not to overwrite the bootloader…

You are right !What is a Bootloader?Atmel AVRs are great little ICs, but they can be a bit tricky to program. You need a special programmer and some fancy .hex files, and its not very beginner friendly. The Arduino has largely done away with these issues. They’ve put a .hex file on their AVR chips that allows you to program the board over theserial port, meaning all you need to program your Arduino is a USB cable.The bootloader is basically a .hex file that runs when you turn on the board. It is very similar to the BIOSthat runs on your PC. It does two things. First, it looks around to see if the computer is trying to program it. If it is, it grabs the program from the computer and uploads it into the ICs memory (in a specific location so as not to overwrite the bootloader). That is why when you try to upload code, the Arduino IDE resets the chip. This basically turns the IC off and back on again so the bootloader can start running again. If the computer isn’t trying to upload code, it tells the chip to run the code that’s already stored in memory. Once it locates and runs your program, the Arduino continuously loops through the program and does so as long as the board has power.Why Install a BootloaderIf you are building your own Arduino, or need to replace the IC, you will need to install the bootloader. You may also have a bad bootloader (although this is very rare) and need to reinstall the bootloader. There are also cases where you’ve put your board in a weird setting and reinstalling the bootloader and getting it back to factory settings is the easiest way to fix it. We’ve seen boards where people have turned off the serial port meaning that there is no way to upload code to the board, while there may be other ways to fix this, reinstalling the bootloader is probably the quickest and easiest. Like I said, having a bad bootloader is actually very very rare. If you have a new board that isn’t accepting code 99.9% of the time its not the bootloader, but for the 1% of the time it is, this guide will help you fix that problem.

https://raw.githubusercontent.com/damellis/attiny/ide-1.6.x-boards-manager/package_damellis_attiny_index.jsonyes ! this is working well for me..!but the same type of problem occurred for me once when I was trying to install node MCU module to Arduino! I don't know the solution for that !

awesome sir !

Superb...!