Adrian_West's instructables
Tell us about yourself!
Achievements
- Adrian_West's instructable ELVEN / CELTIC STAR CHRISTMAS ORNAMENT / BAUBLE's weekly stats:
- Adrian_West commented on Adrian_West's instructable ELVIN / CELTIC STAR CHRISTMAS ORNAMENT / BAUBLEView Instructable »
Thank for the spell check :) I can do math, 3d print, and many other amazing things.... just not spell.
- Adrian_West commented on Adrian_West's instructable ELVIN / CELTIC STAR CHRISTMAS ORNAMENT / BAUBLEView Instructable »
Thank You
- Adrian_West commented on Adrian_West's instructable MOSTER FET - Dual 500Amp 40 Volt MOSFET 3d Printer Heated Bed Drivers
- Adrian_West commented on Adrian_West's instructable MOSTER FET - Dual 500Amp 40 Volt MOSFET 3d Printer Heated Bed DriversView Instructable »
Ya well that one is going to get really hot at 60 Amps. I’m gonna have to say that part is not a good choice. If you run the board at 40 amps it’s fine.
- Adrian_West commented on Adrian_West's instructable MOSTER FET - Dual 500Amp 40 Volt MOSFET 3d Printer Heated Bed Drivers
Ya solid state relays usually have a very low current rating. V*I = watts or Heat dissipation. If you where using 120v AC (in the US). It would be fine. But Lower the voltage and it's a bad choice.
View Instructable »Yes, it should work just fine. I looked at data sheet and did some quick calculations. That part will climb to 133 deg C at 60 Amps. That is assuming that you are in a 25 deg C environment and the part is not in an enclosure.
- Adrian_West's entry PCB Space Fighter - 3d PCB With DOTSTAR Illumination is a winner in the PCB Challenge contest
- Adrian_West commented on Adrian_West's instructable MOSTER FET - Dual 500Amp 40 Volt MOSFET 3d Printer Heated Bed DriversView Instructable »
What SSR are you using? They should not be melting. You can use a MOSFET as a switch but current only flows one way.
- Adrian_West's entry PCB Space Fighter - 3d PCB With DOTSTAR Illumination is a finalist in the PCB Challenge contest
- Adrian_West's instructable PCB Space Fighter - 3d PCB With DOTSTAR Illumination's weekly stats:
- Adrian_West entered PCB Space Fighter - 3d PCB With DOTSTAR Illumination in the PCB Challenge contest
- Adrian_West commented on Adrian_West's instructable PCB Space Fighter - 3d PCB With DOTSTAR IlluminationView Instructable »
Thaks, I will do my best
- Adrian_West commented on Adrian_West's instructable MOSTER FET - Dual 500Amp 40 Volt MOSFET 3d Printer Heated Bed Drivers
Thanks for your comment. 2 parts got added after the fact. I did too good of a job mounting them to the board. You can't even tell that the parts are added. The GITHUB repository has the fixed board. I don't have any of those yet so no pictures.
View Instructable »Thanks for your comment. 2 parts got added after the fact. I did too good of a job mounting them to the board. You can't even tell that the parts are added. The GITHUB repository has the fixed board. I don't have any of those yet so no pictures.
- Adrian_West's instructable MOSTER FET - Dual 500Amp 40 Volt MOSFET 3d Printer Heated Bed Drivers's weekly stats:
- Adrian_West commented on DeroK1's instructable DIY Z-Probe Using Capacitive (or Inductive) Sensor and OptocouplerView Instructable »
Where did you get your optocuppler board?
- Adrian_West entered Simple But Elegant Wall Mount in the BOSEBuild Design Challenge contest
- Adrian_West entered Frame Mount (2020/1515) Universial Spool Holder in the 3D Printing Contest 2016 contest