author

Artclonicc

Inbox View Profile
18Comments

Tell us about yourself!

  • Artclonicc commented on Euphy's instructable Polargraph Drawing Machine2 years ago
    Polargraph Drawing Machine

    This is where you'll put the top edge of your page.....how to make this setting 100mm?

    View Instructable »
  • Artclonicc commented on Euphy's instructable Polargraph Drawing Machine2 years ago
    Polargraph Drawing Machine

    Hi! two questions 1-How to change a constant number of 120 mm, for example 100mm.2 - set the speed and acceleration of 1200 and 1000 -movement is at the level of 700 and 600. There is a limit?

    Home point Y can be less than 120 mm ?

    View Instructable »
  • Artclonicc commented on Euphy's instructable Polargraph Drawing Machine2 years ago
    Polargraph Drawing Machine

    Yes, my crazy setup in about a 2 or 2.5 larger than the original! I will try again - 400 steps per revolution and a circumference of 37 mm (the actual parameters). later, I will unsubscribe ... it would be cool if the beginning of the line coincides with the home point, it is possible in the firmware to prescribe? or difficult? another question-why otsutstvet smooth movement ? it is noticeable that between executions of the commands (draw straight) there is a micro pause micro... is associated with time of transmission from the PC to Arduino? I transfer via Bluetooth organized!

    with the starting point of everything is clear! thank you! question about command -and where the calculation is performed in truglow coordinate system? in the Arduino sketch, or in the software? (all this applies to vector drawing).want to try to write a simple sketch executing commands on a stirred by coordinates x y (or r1 and r2) and raise/lower the pen. feather want to do it on a servo actuator and electric magnet. that is two teams . all parametry will be fixed and prescribed in the sketch. (for specific device). app (convector) on the translation from SVG in Executive command,you'll write to me separately. connection via Bluetooth . Tell me what to do to the smoothness and speed? can the terms of the triangle coordinate system to do in software, not in the sketch? or exercise accu...

    see more »

    with the starting point of everything is clear! thank you! question about command -and where the calculation is performed in truglow coordinate system? in the Arduino sketch, or in the software? (all this applies to vector drawing).want to try to write a simple sketch executing commands on a stirred by coordinates x y (or r1 and r2) and raise/lower the pen. feather want to do it on a servo actuator and electric magnet. that is two teams . all parametry will be fixed and prescribed in the sketch. (for specific device). app (convector) on the translation from SVG in Executive command,you'll write to me separately. connection via Bluetooth . Tell me what to do to the smoothness and speed? can the terms of the triangle coordinate system to do in software, not in the sketch? or exercise accumulation of teams (already converted) in Arduino? I am very interested in this project, could you leave a personal email (if possible) for advice on my project...

    View Instructable »
  • Artclonicc followed Euphy2 years ago
      • Polargraph Drawing Machine
      • Linear Clock
      • Mechanical Expanding Cardboard Lamp - This Way Up!
  • Artclonicc commented on Euphy's instructable Polargraph Drawing Machine2 years ago
    Polargraph Drawing Machine

    Yes! "upload machine spec".but now I saw. that was not grooved 120 to 130 mm it can give such error? another question - when you include "controller" origin starts with x=0, y=0, you can configure the "home point" . the initial path with x=0, y=0 to the "home point" is incorrect (it is impossible to put the pen to x=0 y=0!). feather in hand at the "home point"?

    Yes, my crazy setup in about a 2 or 2.5 larger than the original! I will try again - 400 steps per revolution and a circumference of 37 mm (the actual parameters). later, I will unsubscribe ... it would be cool if the beginning of the line coincides with the home point, it is possible in the firmware to prescribe? or difficult? another question-why otsutstvet smooth movement ? it is noticeable that between executions of the commands (draw straight) there is a micro pause micro... is associated with time of transmission from the PC to Arduino? I transfer via Bluetooth organized!

    View Instructable »
  • Artclonicc commented on Euphy's instructable Polargraph Drawing Machine2 years ago
    Polargraph Drawing Machine

    a link to a working firmware

    View Instructable »
  • Artclonicc made the instructable Polargraph Drawing Machine2 years ago
  • Artclonicc made the instructable Polargraph Drawing Machine2 years ago
    Polargraph Drawing Machine

    crazy settings, but they turned out a little bit. managed to draw a dragon but it is much more mirrored (this is engine -I know how to fix) but the scale do not. he attached a photo of the original dragon and what happened. the A4 sheets.# *** Polargraph properties file *** #Thu Mar 16 21:36:13 MSK 2017controller.pixel.samplearea=10controller.pictureframe.position.y=15controller.pictureframe.position.x=15controller.testPenWidth.startSize=0.5controller.machine.colour=969696machine.motors.mmPerRev=90controller.vector.filename=E\:\\Arduino\\\u0431\u0430\u0431\u0430.svgcontroller.window.width=1366controller.frame.colour=C80000controller.image.position.y=357controller.image.position.x=357machine.motors.accel=1000controller.image.height=237controller.machine.serialport=6controller.windo...

    see more »

    crazy settings, but they turned out a little bit. managed to draw a dragon but it is much more mirrored (this is engine -I know how to fix) but the scale do not. he attached a photo of the original dragon and what happened. the A4 sheets.# *** Polargraph properties file *** #Thu Mar 16 21:36:13 MSK 2017controller.pixel.samplearea=10controller.pictureframe.position.y=15controller.pictureframe.position.x=15controller.testPenWidth.startSize=0.5controller.machine.colour=969696machine.motors.mmPerRev=90controller.vector.filename=E\:\\Arduino\\\u0431\u0430\u0431\u0430.svgcontroller.window.width=1366controller.frame.colour=C80000controller.image.position.y=357controller.image.position.x=357machine.motors.accel=1000controller.image.height=237controller.machine.serialport=6controller.window.height=706controller.maxSegmentLength=2controller.geomerative.polygonizerLength=1machine.penlift.up=180machine.penlift.down=90controller.page.position.y=130controller.vector.scaling=100controller.page.position.x=55controller.pictureframe.width=380machine.step.multiplier=1controller.grid.size=75.0controller.testPenWidth.endSize=2controller.pictureframe.height=555controller.page.colour=DCDCDCcontroller.testPenWidth.incrementSize=0.5controller.image.width=237machine.motors.stepsPerRev=1700machine.pen.size=0.8controller.page.width=300controller.pixel.mask.color=00FF00controller.machine.baudrate=9600controller.vector.minLineLength=2machine.width=410controller.geomerative.polygonizer=1controller.page.height=400controller.vector.position.y=141.1controller.background.colour=646464controller.image.filename=controller.vector.position.x=99.41controller.homepoint.y=130controller.guide.colour=FFFFFFmachine.motors.maxSpeed=1100controller.homepoint.x=205controller.density.preview.style=5controller.pixel.scaling=1controller.densitypreview.colour=000000machine.height=585

    View Instructable »
  • Artclonicc commented on Euphy's instructable Polargraph Drawing Machine2 years ago
    Polargraph Drawing Machine

    how to upload settings to the controller figured out! the problem is the disparity between millimeters and distance, and a pen. here are my settings, what's the problem? # *** Polargraph properties file ***#Thu Mar 16 20:24:11 MSK 2017controller.pixel.samplearea=10controller.pictureframe.position.y=15controller.pictureframe.position.x=15controller.testPenWidth.startSize=0.5controller.machine.colour=969696machine.motors.mmPerRev=37.68controller.window.width=1366controller.frame.colour=C80000controller.image.position.y=357controller.image.position.x=357machine.motors.accel=400controller.image.height=237controller.machine.serialport=6controller.window.height=706control...

    see more »

    how to upload settings to the controller figured out! the problem is the disparity between millimeters and distance, and a pen. here are my settings, what's the problem? # *** Polargraph properties file ***#Thu Mar 16 20:24:11 MSK 2017controller.pixel.samplearea=10controller.pictureframe.position.y=15controller.pictureframe.position.x=15controller.testPenWidth.startSize=0.5controller.machine.colour=969696machine.motors.mmPerRev=37.68controller.window.width=1366controller.frame.colour=C80000controller.image.position.y=357controller.image.position.x=357machine.motors.accel=400controller.image.height=237controller.machine.serialport=6controller.window.height=706controller.maxSegmentLength=2controller.geomerative.polygonizerLength=1machine.penlift.up=180machine.penlift.down=90controller.page.position.y=130controller.vector.scaling=100controller.page.position.x=55controller.pictureframe.width=380machine.step.multiplier=1controller.grid.size=75.0controller.testPenWidth.endSize=2controller.pictureframe.height=555controller.page.colour=DCDCDCcontroller.testPenWidth.incrementSize=0.5controller.image.width=237machine.motors.stepsPerRev=400.0machine.pen.size=0.8controller.page.width=300controller.pixel.mask.color=00FF00controller.machine.baudrate=9600controller.vector.minLineLength=2machine.width=410controller.geomerative.polygonizer=0controller.page.height=400controller.vector.position.y=330controller.background.colour=646464controller.image.filename=controller.vector.position.x=205controller.homepoint.y=530controller.guide.colour=FFFFFFmachine.motors.maxSpeed=600controller.homepoint.x=205controller.density.preview.style=4controller.pixel.scaling=1controller.densitypreview.colour=000000machine.height=585

    View Instructable »
  • Artclonicc commented on Euphy's instructable Polargraph Drawing Machine2 years ago
    Polargraph Drawing Machine

    hi. have a problem, I have not saved the last loaded configuration in the controller. connect. team engines perform. when checking port monitor is loaded parametry the same. how to load new settings into the controller?

    View Instructable »
  • Artclonicc commented on Euphy's instructable Polargraph Drawing Machine2 years ago
    Polargraph Drawing Machine

    Hi! I have Arduino UNO R3. Motor shield motor control. The engine is 1.8 degrees (200 steps per revolution).Gear diameter 12 mm Length of circumference of 37.68 mmWhat settings should I put?mm/Rev = ?- steps/revolution = ?- step Mulitplier = ?Another question: On Arduino UNO, a possible micro-step?Motor shield, control Board motors [L293D]FL39ST 1.8°, NEMA 16 (39 мм)6 contacts , but I use 4 pins

    View Instructable »
  • Artclonicc made the instructable Polargraph Drawing Machine2 years ago
    Polargraph Drawing Machine

    Motor shield, control Board motors [L293D]FL39ST 1.8°, NEMA 16 (39 мм)6 contacts , but I use 4 pins

    View Instructable »
  • Artclonicc made the instructable Polargraph Drawing Machine2 years ago
    Polargraph Drawing Machine

    Моторный щит, щит управления двигателями[L293D]FL39ST 1.8°, nema и 16 (39 мм)6контакты , но я использую 4-контактный

    View Instructable »
  • Artclonicc commented on Euphy's instructable Polargraph Drawing Machine2 years ago
    Polargraph Drawing Machine

    Motor shield, control Board motors[L293D]FL39ST 1.8°, NEMA 16 (39 мм)6contacts , but I use 4 pins

    View Instructable »
  • Artclonicc commented on Euphy's instructable Polargraph Drawing Machine2 years ago
    Polargraph Drawing Machine

    Hi! I have Arduino UNO R3. Motor shield motor control. The engine is 1.8 degrees (200 steps per revolution).Gear diameter 12 mm Length of circumference of 37.68 mmWhat settings should I put?mm/Rev = ?- steps/revolution = ?- step Mulitplier = ?Another question: On Arduino UNO, a possible micro-step?

    View Instructable »
  • Artclonicc commented on Euphy's instructable Polargraph Drawing Machine3 years ago
    Polargraph Drawing Machine

    Hi! There is an idea to upgrade your project. To communicate with the Arduino controller, via USB. I want to consult with you about the SVG format commands, which are transmitted to the line in port of the Arduino controller.Question:Commands from the SVG file in this format is passed to the controller? (example)<path d="M117.136 51.4184c0.245,0.035 0.4897,0.035 0.7349,0.1225"/><path d="M117.871 51.5409c0.455,0.5424 0.5777,1.2773 0.4197,1.96"/><path d="M118.29 53.5009 c-0.5774,2.345 -1.6098,4.6197 -3.1496,6.4923"/>Understands the format controller?Or they are transmitted in a different format?

    View Instructable »
  • Artclonicc commented on Euphy's instructable Polargraph Drawing Machine3 years ago
    Polargraph Drawing Machine

    Hi! Great project!!! I have a question. You can pass the ready G-code to Arduino via the terminal app? Do not use your software. Will work? If not, then how to do it?

    View Instructable »