Tell us about yourself!
Cordless Power Tool Conversion 18VDC to 120/240VAC
I have the extruder fan connected where the second extruder heater coil should go as you describe, though I am running into trouble when trying to print with PETG filament and having modded my extruder fan from the stock 30mm to a better 40mm fan, it's actually cooling the print bed and causing prints to fail. If I understand right there is a connector somewhere on the board where you can connect the fan and have the gcode control the fan. This would help since there is an option in my Cura slicer for turning the fan on and off, and using OctoPrint I have the option to control the fan from a control panel as well. So this is just me asking where I can find the fan connection on the RAMPS 1.4v board to move the extruder fan connection to those pins.
Converting a Thinclient Into a Desktop Computer
I can be added to the list of people who is upset about the drop of the mobile app. I used it a lot for browsing through new and interesting instructables and sending out ones I thought were interesting out to friends. Now that the support is gone and even the images have stopped being posted to everything, the app is totally unusable. I would vote to have the app brought back, I have an older Note 8 and a Galaxy S3 device, and the web browser version is a very hard one to navigate. This choice was a bad one. Please reconsider.
3D Printed Animatronic Puppet
Pulled Turkey Nachos With Beans and Babycorn Recipe
Build Your Own Surveillance Camera With Raspberry Pi and Motioneye
The Arduino Synthesizer
It does not show up with the USB0 com port on my desktop. Ive tried this same setup on another linux machine and I have to go through the same steps to get the sketch to load onto the board. I have to have the "upload_router" script running in an open terminal window for the DFU to see the board after I hit its reset button, it then catches it and then I can upload to the board, then the IDE resets the board and it runs the newly uploaded script. I have been talking to Roger Clark on a Gitter chat room about this very issue. When I figure out what the issue is I shall report back with the solution.
Build a Waldo for Arduino Robot Arms
Alright, got all my boards flashed properly now. Should I move both boot pins to 0?When I plug it in by USB it doesnt show up.
Well I have made some progress.Here is where I am at. Ill provide screenshots of what the IDE is showing. When I run the IDE it compiles and sends it to the device, it says it completed correctly, but the PC13 led is still blinking quickly. I can't figure out why it is not running the script. Still really happy with the progress I have made though. Eagerly waiting for your reply.
I am having the same issues you are, but I am on a linux machine, so I don't think this is something to do with what OS, but more has something to do with either the IDE or the board.
I am at this same point myself. Just got ten boards all sucessfully flashed with the bootloader. Can't get the aurduino ide to see the board though.
Arduino Controlled USB Trackpad
Trying to flash this with all the settings you have described, but each time I try to connect, the flashing utility says this to me. "No response from the target, the Boot loader can not be started.Pleas, verify the boot mode configuration and the flash protectionstatus,Reset your device then try again..."I have both jumpers set to 0 and I am using an Arduino Duemilanove without the arduino chip installed as an FTDI programmer. P.S. When this is all programmed correctly, I won't need to use an FTDI device to program it each time, I could program it over the on board USB port?
Arduino Examples #2 Use an Arduino As a FTDI Programmer
Amazing Keychain (with a Bike Chain)
NOISE FROM TOYS (Part I)
Make Your Own Cheap Portable MP3 Player (Bluetooth, USB, AUX, SD Card, FM)
Lab ATX Powersupply
Converting Old Tea Light Lanterns Into Romantic Solar Garden Lights
Lets Program a PIC Microprocessor
Picked up 10 of these boards, for the price its SO worth it.
Will these instructions work out the same way with someone who is on a Linux bases operating system?
Well I do have windows on a virtual machine, until then Ill do that. Let me know if you do come up with a linux friendly way. Going to be getting a few of these boards just for my parts bins. :P
Amazing ARDUINO Killer
LED Hollow Log Lamp
Getting Started With Eclipse in 5 Steps
Painting and Finishing EVA Foam and Worbla
Introduction to Worbla
Introduction to EVA Foam
Intro to Neopixels
Attach a Patch
From Sketch to CAD to 3D Print
Solar Based Power Supply for Arduino
Inexpensive EDC Pocket Organizer
Create VPN on Your Raspberry Pi Device
3D Printable Phage (A Guide to Modeling for FDM Printers)
Rusty Junk to Useful Stuff With Chemistry!
Transform the SF Clipper Card Into a Wearable
Hard Drive Sander
Multi-External Hard Drive Power Supply
Ferrocell, Magnetic Fields Viewer
Raspberry Pi Vital Monitor Via OLED
DIY Cathode Ray Tube: Interacting With Electrons
How to Make Oyster Sauce Shrimp Noodles
Variable Lab Bench Power Supply.
LED As Light Sensor !!!
BUDGET SCREENPRINT DIY
Making an Audio Mixer
Oil Lamp? Oh, Boy! Don't Spill It!
TeamViewer on Raspberry Pi
PVC Pipe TV Stand
Modern LED Desk Lamp...Powered by 5V USB
$20 Mecanum Wheels With Rubberized Rollers
Build a Giant 3D Printed Robot Arm
Raspberry Pi Zero Keyboard Computer
Zero Mess Hot Glue Molds? It! Could! Work!
How to Make a Modular Queen Storage Bed
Reusable Bleaching Stencil
3D Printed Bionic Hand Skeleton
Five Pointed Rainbow Prism Lamp
VU METER (Part-2) Using LM-3914 & LM-3915
LED Light Box
Cheap Music Reactive Light Show
Laser Box Music Laser Light Show
Does the original power supply for the printer suffice for working the RAMPS board, or do I need a switching power supply with a 12v rail and a 5v rail?
3d Printed Gearbox for Small Dc Motors
The Glow Cloud
Growing Crystals on LEDs and ETextiles
Portable Multimedia Speakers V2
Chicken Spinach Cream Pizza Ring Recipe
PCB UV Exposure by Recycling an Old Scanner
Also, am I able to print from an SD card, or does this machine need to be perminantly connected to a computer to print from now on? And if so, am I able to use Cura 2.3.0?
Replace Monoprice Select Mini Controller With Arduino Mega & Ramps 1.4
Polishing Bottle After Cutting
Monoprice Mini: Remove Broken Filament From Nozzle
3D Printed Wire Stripper
3D Printed Arduino Robot Arm - LittleArm 2C
Broadcast Your Own Number Station on the Raspberry Pi
Make a Pocket Hole Jig
Bottle Cutting With a Soldering Iron
DIY Switch Plate Covers
Digital Wall Calendar and Home Information Center
Flower Dome Retro Module
DIY Shop Air Cleaner
Modular DIY CNC Machine for ~$300
18v Makita LXT power pack - Cordless to corded conversion
Making a Death Trooper Ring - Silver Ring With Green Glow & Black Corian
Quick & Easy Lightweight Work Bench
Modular Parts Storage
ARDUINO IR REMOTE (USE YOUR OLD REMOTE TO CONTROLL HOME APPLIANCES)
Would be cool to make a clear epoxy fill with some of that ten hour glow powder and fill in all the little holes in the top, sand it down level and then seal it in with a clear coat layer.