MissionCritical

well thats a very good explaination, thanks a lot for sharing this concept, please share any more suggestions or learning resources in this topic, i would love to do more such remixes in future!

Thank You

about this my friend, i believe WIFI communication doesn't work on UART, there is some other problem, which i am trying to figure out along side you.

My friend, you only need to connect to USB Serial to get the IP address, once u get the IP, disconnect the USB from PC and continue on 5V power supply

although it can be done very easily by adding a cheap Chinese speaker and run it on SD with just 1 sound effects, or by Arduino, which for my use wasn't necessary but definitely did thought of it

Reminds me of Billie Eilish " Lovely " song

i want to try 3 things in exact order.1. check if your ESP is powered when you disconnect the USB.2. change USB port ( plug wire in other port ).3. change port (80) to (81).4. let the program upload, ( while USB connected ) then let it show the IP address and then disconnect the USB and paste the same ip add to mobile phone app LEDFx.after this let me know what happens

can you share a screeenshot of your error code, so that i can tell you exactly how to fix the problem.

glad you liked it, do share it in " i made it " once you make it, i would love to watch it in action!

Thanks but not more than u :)

This code is for ESP8266 ( NodeMCU ) which is different processor. Try using the code i attached in this comment or try it on Node mcu. I hope this was helpful :)

Thank you :)

Comments like this make my day ( and a weeks work) worth while :)

Thank you :)

glad you read it till end and liked it! Thank you so much!

you have truly made our Indian snack interesting, i loved the masala twist you added in it! proud of you good going!

Nicely done, looks yummy!

yes definitely a step in direction to try and make it cheap, had to start and try some where!

looking forward to your suggestion/ feedback in same!

this is awesome, i wish i had SMD solder station to pull off this project!

yes infact, i would like to try that in one of my next projects, not sure about LED though

sure i will connect with you for any help thanks a lot! :)

glad that you loved it :)

hahaha surely in my next version i will do that :) and would love to work with you

glad you liked it 🥰

glad that you liked it! :)

sure i will give it a try in my next project, totally looks neat!one question, is it open source? can i use it for my projects and record it for youtube videos without getting into legal issues?

glad you liked it! :)

just beautiful ❤️

That is basically connecting the Screw terminal on PCB to power entire board. its kept aside yet it is connected, we call it as Net Labelling which basically means that name labelled things are interconnected just a software trick.for now consider that as VCC and Power Pins on board

try this code https://www.mediafire.com/file/y7gs4ednxcsollh/Mis...

surely can breathe in this mask, its me in the pictures i literally had this mask on for few hours and hurray i am alive 😂😂😂😂

indeed all gimbals will come with such high settings, since they are made for FPV, do check the settings we mentioned above!

thank you man!

it could be possible, i haven't played a lot with ATtiny85, do let me know if you try it!

thanks a lot :)

most welcome ivymaker

thank you <3

yes definitely works on Go Pro hero 8!

thank you ;)

thanks :)

i think that makes sense, i should make another PCB with all components on on board rather than wiring up the Joystick Module externally, what do you think?

glad i could help you!

yes sure, that was autogenerated didnt notice it until now!

glad that you liked it, thanks a lot for your support! :)

https://www.mediafire.com/folder/bd758ybt8cznn/MPU+6050+Teapot

i have a dedicated post for same, please check this out https://www.instructables.com/5-Most-Common-Arduino-Nano-Clone-Problems-and-Thei/

you can use 2.4mm pitch Male / Female connector pins for the same