Tell us about yourself!
- sny2ksa followed Mohannad Rawashdeh
By Mohannad Rawashdeh
- sny2ksa followed MertArduino, manu4371 and BoianM
- By MertArduino
- By manu4371
- By BoianM
- sny2ksa followed sureshmali
- By sureshmali
- sny2ksa commented on SteveQuinn's instructable IoT Mains Controller. Part 9 : IoT, Home Automation
- sny2ksa commented on instrbles37568's instructable Quick and Easy ESP8266 Plug Via OpenHABView Instructable »
Hi,I try to build a basic project using espeasy + RPI3 with openhabian 2,1 and mosquito. everything is going fine but relay not working, I can turn on and off relay using espeasy commands using web browser all screens shots are attache can some one tell me where i am wrong.additionally i want to add timer on this relay with save the relay state during power failure
- sny2ksa commented on chimeranzl's instructable Wifi to RF - Door LockView Instructable »
Hi,I try to build a basic project using espeasy + RPI3 with openhabian 2,1 and mosquito. everything is going fine but relay not working, I can turn on and off relay using espeasy commands using web browser all screens shots are attache can some one tell me where i am wrong.additionally i want to add timer on this relay with save the relay state during power failure
- sny2ksa followed instrbles37568
- By instrbles37568
- sny2ksa commented on instrbles37568's instructable Part 2 OpenHAB, MQTT, and ESP Easy - Build Your Own DIY NodeView Instructable »
Hi,I try to build a basic project using espeasy + RPI3 with openhabian 2,1 and mosquito. everything is going fine but relay not working, I can turn on and off relay using espeasy commands using web browser all screens shots are attache can some one tell me where i am wrong. additionally i want to add timer on this relay with save the relay state during power failure.
- sny2ksa followed tomaskuchler
- By tomaskuchler
- sny2ksa commented on abhishek7xavier's instructable DIY Smart Home Automation using AndroidView Instructable »
Dear Abhishek,Please have a look on the error message and guide to solve the issur.Best regards
- sny2ksa followed abhishek7xavier
- By abhishek7xavier
- sny2ksa commented on AlanV2's instructable Smart Home Automation with Android + Ethernet Internet + ArduinoView Instructable »
Dear AlanV2,Please have a look on the attached image. I try a lot but got same error.i use the IDE 1.5 , 1.05 . 1.5.3.Can you guide me how to solve the issue
- sny2ksa commented on Ardumotive_com's instructable Arduino Based Smart Home IOT SystemView Instructable »
:) Today I tested it at home and its working.Thanks a lot
- sny2ksa commented on Ardumotive_com's instructable Arduino Based Smart Home IOT SystemView Instructable »
Ethernet shield i tested it with other codes its working well and yes its based on W5100. The network setting are ok. Today i will try again and inform you the results
- sny2ksa commented on Ardumotive_com's instructable Arduino Based Smart Home IOT SystemView Instructable »
try a lot but failed, program the uno using codbender without error then plug the Ethernet cable but unable to open the page 192.168.1.192. i am using clone ethernet shield with original uno board. Can you help me to diagnose the problem.
- sny2ksa commented on Ardumotive_com's instructable Arduino Based Smart Home IOT SystemView Instructable »
get error ShiftRegister74HC595.h not foundfrom where i will search.
Hi,I try to build a basic project using espeasy + RPI3 with openhabian 2,1 and mosquito. everything is going fine but relay not working, I can turn on and off relay using espeasy commands using web browser all screens shots are attache can some one tell me where i am wrong.additionally i want to add timer on this relay with save the relay state during power failure