Tell us about yourself!
Compact Dust Collector
1/4" at the base with a full length distal taper to just under 1/8" above the bevels at the tip.
The bar stock was .25" x 1.75" hot roll. The finished blade was a bit over 2" at the widest point by 18" long.
How I Make Cool Metal Inlays
Wooden Steampunk Ring
Recreating the Universe in the "Cosmic Rift" Table; AKA: How to Build a Resin Table Like a Boss!
Modern Media Console
How to Make Metal Flowers
Make a Dragon Eye, Secret Compartment Book Introduction
French Cleat Wall & Storage Loft
Japanese Tanto Knife Stand
Walnut and Copper Cutting Board / Serving Board!
Reclaimed Lift-Top Coffee Table
How to Bend PVC & Make Incredible Shapes
How to Make a Wooden Shield
The Ultimate Lumber Storage Cart
DIY Kiridashi Knives
Multi-Color Custom T-Shirts
3D Printed Bobblehead
Leather Mystery Braid Cuff
How To: Restore an Axe- Two Tone Handle/Leather Sheath
How to Build a Wooden Desk Lamp
Knife Block - Warrior
DSLR Macro Photography: a Comprehensive Overview
All About Coin Rings! Make Your Own!
3D Scanning Class
How to Make a Wood & Hammered Silver Ring
Mega Torch - the ultimate guide
How to build an insanely bright LED flashlight!
I suggest that you buy some steel and supplies from http://newjerseysteelbaron.com/:)
I've handled and shot Garands and carbines, but a very long time ago, so I'm no expert. The unanimous consensus among people I trust is that it's a carbine.
This one was custom for a very large man, so the handle is about 4.75". For an average sized hand I'd go 4.25".
I have made some forges, but not the one in the pics. It's an Ellis forge with a T-Rex burner. Thank you!
Contests entered - pending approval. Thanks!
No... I'm not seeing any that apply. Did I miss one?
Not in this case. I'm very careful not to put copper in my forge at high temps (steel forging temps). It melts and gets in the forge lining, takes forever to burn out, and is very effective at preventing forge welding. At the first sign of green flames I would have stopped forging and cleaned the barrel.
Not in this case. I'm very careful not to put copper in my forge. At the first sign of green flames I would have stopped to clean it out.
4140 won't form a hamon. The 10 series steels and W2 are best for that. I've done quite a few of them in the past, and I'd post some pics in my response, but the Add Images button isn't working.
I did make the sheath. I used Tru Oil on the handle - seemed appropriate since it's used to finish gunstocks. Thanks!
Yeah, I hear it a lot that most people would have restored the stock - and a few that would have re-bored the barrel. This was the choice of the gun's owner. The steel chose the finish on this one. It was an absolute bear to work with. Very hard to move under the hammer and impossible to forge weld. The machined shapes and grooves in the original piece became artifacts in the blade, and a mirror finish would have accentuated them in a bad way.
I hadn't thought of that. Thanks!
A knife from a shot out M1 ...View Instructable »
The Walking Dead Intro Knife
Impossible Nail in Wooden Block
The Ultimate Wire Soldering Guide for Beginners
How to Make a Pure Black Photography Background!
3 parts bronze powder to one part methylcellulose by volume. Carboxymethylcellulose will work. I used room temperature water - just enough to get a very thick clay - too thin and it's sticky and will sag.
3 parts bronze powder to one part methylcellulose by volume. Carboxymethylcellulose will work. I used room temperature water - just enough to get a very thick clay - too thin and it's sticky.
I buy all my blade steel at http://newjerseysteelbaron.com/The Baron ships fast and offers the best quality blade steel that money can buy.
Yeah, I know this is a pretty high level overview. I intend to do a separate Instructable for each stage as I do them on new projects. THANKS!
I intend to! Thanks!
I made the mold with two part silicone molding compound. The original is a refrigerator magnet I've owned for years.
Thanks, I appreciate it!
Thanks! It was fun to make.
Mini Plasma Pen & Micro Torch