Concrete stepping stones

I have made some concrete stepping stones (for decorative use in flower beds mainly) and have painted them to give them a detailed look. I used exterior paint,  Now I'm wondering what I should use to seal them to protect the paint from chipping and fading?

Topic by Gdlucas   |  last reply


fiber reinforced concrete $$$

Online i can see that a 60 lb bag from quickcrete is about $5. ok. easy.   Shipping----$20 to----$50----- ouch. so .   where to find it?      gotta be someplace that has 1000s of lbs of it on the shelf, and sells it at 5 or 10 bucks.

Topic by Toga_Dan   |  last reply


Raise Sunken Concrete?

Hello. I have a 5x5 concrete porch that has sunk 6-8 inches. The porch consists of a top surface with an 18 inch skirt, and a step. I believe it was a single pour.  The porch itself is in good condition, so I am seeking methods of raising it. I have looked into slabjacking, and pressure-fill lifting, but was actually looking for a pneumatic solution. any thoughts, comments, anecdotes, would be greatly appreciated. Thanks

Question by sgunkler   |  last reply


type of cement for building concrete benches?

I recently bought a bench mold so I could build a cement garden bench   The mold has some delicate designs in it.   I tried using quikrite 5000 and other cements with basic aggregates already premixed, but it did not come out crisp. The designs were pitted by aggregates I think.   I am wondering if a simple Portland cement with only sand would work? I also incorporate rebar as well?

Question by JamesP250   |  last reply



What can I do with broken concrete, concrete in small slabs?

I have a lot of concrete from an old driveway that I got rid of with a sledgehammer. I dont have a truck to dispose of the concrete somewhere. So need to do something with it around my house.

Question by DELETED_nuwave   |  last reply


Concrete propane grill - Heat issues?

I'll be making a concrete counter top for my outdoor kitchen. I'll shape a "box" in the concrete (just like a concrete sink), and build the propane burners into that. Will I run into any heat issues with the concrete? Should I line it with something to shield it from heat?

Topic by DenMike99   |  last reply


how do I replace a badly broken concrete step? Do I use rebar with the new concrete ?

What kind of concrete and how would I hold the concrete in place till it sets up? This is a top step

Question by markslanding   |  last reply


How do I lift and repair a concrete slab in a walk? Answered

How do I lifta broken coner of a concrete slab in the walk at the front of my house?

Question by    |  last reply


How can I lay cobblestone type paving over a pre-existing concrete slab??

We have this ugly patio slab mid yard and thought to dress it and its ajoining pathways up with cobblestone style paving such as we saw in Spain. I'd use river rock or round stones from the home DIY stores but do I lay cement and set the stones in or some sort of outdoor thinset and grout? How should I prepare the slab surface (its plain old cement/concrete and too big to smash and remove)? Please advise.

Question by Knitwitch   |  last reply



Right ratio for making bowls with concrete? Answered

I recently got someone to buy me concrete mix - I asked for ready mix as I've seen people suggesting Quikrete, but I ended up with 2 bags - one with the cement and one with the gravel and sand. Now, I want to make smallish bowls for outdoor use over the weekend (bird baths, small plantholders, etc.), but I'm not sure what my ratio must be for the sand / cement or sand / cement and gravel mix (and I'm not planning on buying another product). I've read that people can mix only the sand and cement for a smooth finish, but will this be strong enough? The gravel I have is quite large, and it might make the finish too chunky when the concrete is dry. I'm also planning on not using bowls or containers as molds - I want to smooth it out on the outside or inside of a bowl by hand with a trowel or something similar. Will I be able to make this work? I want to make small bowls, so I don't need to mix large amounts at once. I have never worked with concrete before, so I want to start out with small items anyway just to get the hang of things.

Question by Nocturmia   |  last reply



Raised Garden Beds out of Concrete Blocks?

I want to build raised garden beds with the walls being made out of concrete cinder blocks. Want the beds to be about 2 1/2' above ground and about 3' to 4' wide. I also want to make basically concrete counter tops to put on top (or benches). My question is .. how many inches can the top go beyond the concrete cinder block frame without having to add braces for the bench? Ex: if I use 6" wide cinder blocks .. and fill the holes with rebar and concrete .. what is the overhang I can have on the bench top?

Question by RayVyn   |  last reply


where can i get small bags of fast setting concrete from?

Im making special objects like small bricks and things and i need to know where to get some

Question by sharlston   |  last reply



Concrete Cinder Block for raised garden beds?

I would like to build raised beds approximately 2 1/2' tall and between 3 1/2 to 4' wide (planting area). I want to construct the "walls" out of concrete cinder blocks .. I ALSO want to place a 2" thick concrete "counter or bench" top on the wall. My question is .. how far of overhang can I have for the "bench slab" on top of the "wall" without having to add braces etc? EX: if I use 6" wide cinder blocks (with rebar & concrete) .. and the wall is only between 2 1/2 to 3 feet tall .. and only being used to contain soil .. not to withstand major structural elements .. how far can the concrete bench top extend from the front of the wall?

Question by RayVyn   |  last reply


I want to make fake granite. Seen the retaining walls along the road turned into faux granite outcroppings?

I've seen some really realistic-looking fake granite. There's a hotel lobby filled with a 'granite' water feature, and along roads they're putting in retaining walls then covering them with concrete that's dyed and shaped to look like a granite outcropping! I'd love to learn how to do that. Can anyone tell me how to do that?

Question by needexercise3   |  last reply



how would I make a large concrete human head?

I would like to make a large garden sculpture of a woman lying down.  I mainly want the head, neck, shoulders and one arm and foot of  concrete.  The rest would be soil and plants to build up the body and a ground covered blanket for covering parts of her.  I want it to be at least life size, preferably larger.  Should I make a solid concrete head?  What would I use to cast it?

Question by Jeanhopper   |  last reply



How do you get paint to adher to a concrete verandah?

My home has a large varandah that is smooth concrete and it looked poor so I bought special paving paint but it peeled off pretty quickly. I used steam to clean surface and a wire brush to make sure that the paint would have the best chance of adherring but it did not work. The paint began peeling within a few weeks.

Question by rmyardley   |  last reply


Washout! Is there a good way to backfill under a concrete driveway?

I just purchased a home, and we discovered some water damage to the fill under the driveway and front walk.  The driveway still has intact slabs, but a little freezing and thawing and I will have gravel instead.  I was thinking about trying to shove paver sand under the slabs, and into the gaps along the sides.  I was just wondering if anyone had a better idea, or suggestions on how to get the sand underneath and compacted enough to make a difference this winter.

Question by Rutabaga1000   |  last reply


Lifting form?

Garage plates water damage; need refresher course on plate raising with threaded rod & concrete.

Question by WendellB8   |  last reply


remove oil stains from driveway?

How to remove old oil stains from concrete driveway

Question by    |  last reply


Does anyone know to make concrete or like material head planter for outdoor plants?

Hello Wonderful, and Creative people, I need your help in achieving the same or similar look to these terracotta/concrete planter, with an aged moss green patina, $85-$125 at HGTV Marketplace Ouch!!! I would like to use these for small outdoor plants! and achieve the same awesome look for less? I would appreciate any suggestions before embarking in uncharted waters. I was thinking of using those Styrofoam heads and cutting a hold big enough to accommodate a flower pot. What should I use to prep for water/weather proofing...paper Mache, shellac, paint and glue moss??? Please advice this novice. Thank -U-much! Lilmamahttp://stonefacecreations.homestead.com/PRODUCTS.html

Question by lilmamacita   |  last reply


Any ideas on cheap gazebo/marquee weights to hold down the legs?

Some marquees are going on concrete surfaces, some on grass.

Question by LadyFizz   |  last reply



help needed on how to make a rock retaining wall and sealed with concrete?

Well, my front yard is currently supported by piles of rocks where there is a ditch next to it, however only when there is heavy rainfall that the water passes through the ditch otherwise its empty.  The piles of rocks were placed one onto the other and these were never mortared and neither has a good base.  So, I have a huge amount of stones in my yard that I wanted to get rid of and also the quality of the soil where I live is very poor as it is like mortar when humid and blocks of soil when dry which I was thinking of using as backfilling. My question is how can I use the existing rocks to rebuild the retaining wall well, solid and also have a good look. By the way I live in Mauritius where the climate is humid and I live rather close to a mountain and river and the rocks are lava rocks meaning very hard. Please give me instructions on how to make everything from building the trench to finishing the wall and the tools that will be needed. thanks

Question by Chamburn   |  last reply


How can I create a mold for a large concrete pot ( greater than 1.5 by 1.5 metres) ? Answered

I wanted to have series of pots next to a deck . Rather than just square,I wanted to have something like half a sphere drawn up; maybe a better way to describe it is a cone with the point cut off and inverted. I could make an internal mold with heaped wet sand , but how can I mold the walls for consistent thickness, reinforcerd with wire and asmooth exterior The problem is to create a pourable mold in an interesting shape.

Question by    |  last reply


Help Making Papercrete Garden

Hello, I was thinking about ripping out all the rotted wood in my backyard garden and replacing it with basically a waist high garden area to grow herbs and I stumbled upon papercrete one day. I've never used papercrete let alone concrete in general. I was just wondering if I could get some general help on where to start. I'd like to make this out of papercrete block and papercrete mortar if all possible but I don't know what amount of newspaper, water, and portland concrete I need... or even how to make molds. -Jimmy

Topic by rexdino5   |  last reply


Spontaneously Combusting Elephants

Thought you might all like to have a chuckle, as I did when I recieved this saftey alert. Priceless simply priceless... Enjoy ;) Apparently the concrete Budda's weren't to crash hot either. Pardon the pun.

Topic by Lftndbt   |  last reply


Can you use earth cement for pads for livestock?

I would like to create a pad in front of my cattle's feeder with a earth and concrete mix.  Does anyone have a recipe for this?  I know that they use this in homes with an earth floor. 

Question by officer19972004   |  last reply


Would like to make something different to cover the septic tank covers?

We thourght about the Easter Island statues but not sure how. Chicken wire, paper mache and concrete mixed with vermiculite to make it lighter any ideas?

Question by barsue   |  last reply


disk saw + vacuum cleaner = less dust ?

When cutting bricks and concrete with disk saw there are clouds of dust. here is my failed attempt to reduce its amount using a vacuum cleaner instructable anyway ?

Topic by 11010010110   |  last reply


What would be the VERY BEST way for me to TRANSITION into my newly adopted off-grid, survivalist, subsistence lifestyle? Answered

A 16'x16'x16', 256-square foot, A-frame cabin on an elevated 3' concrete paver floating DekBlock foundation with a 3'x 6'8" front flush door, one rear 48"x 48"horizontal slider window, and another upper 24"x 24" horizontal slider window for the sleeping loft.I'm thinking that one of those standard U.S. Stove designs might provide just a little too much heat for my needs up in the Copper River Basin region of ALASKA's rural backcountry. Who knows? What are your suggestions for the above described "habitat"? Where can I find the best deals for my 256-square foot space? (Heating/ventilation-wise, we're speaking of subzero temperatures and heavy snowfall, so, I don't believe that "opening a window" is a practical solution for me if it gets too hot and smokey inside my A-frame.) Plus, I've done the HEATING ESTIMATE for the A-frame I'm going to build and the numbers come out to about a 620,000 btuh (heat loss) for the new dimensions I'm finally settling on: 16'x16'x16' or 256sq.ft. This calculation is for -50 degrees F with cold floor, ceiling, and glass surfaces taken into account. (Insulation isn't a factor this early in the design.) "Wow!" I thought at first. "A 620,000 btuh HEAT LOSS! I reckon you can never have too much stove even for an A-frame design." (Being that A-frame cabins retain heat so well, and that my sleeping loft may get really HOT in the Winter, this was a preliminary concern.) Foundation:(4) 8"- diameter cardboard cylindrical concrete forms for pin-point piers;(4) 84" reinforcement rods for pin-point concrete forms;(16) Bricks for base of footing;(24) Layout stakes;(8) 5' batter boards;(1) Spool of wire for joining the two 14" reinforcement rods for each footing base;(1) Spool of line for marking building layout lines;(?) Bags of cement;(?) Bags of gravel;(?) Bags of sand...*A few questions about the amount of concrete needed for the four footings and the four concrete piers: "How much concrete will be needed for four 8"-deep concrete footings poured into four 16"-diameter, 44"-deep holes with each containing four bricks and the four reinforcement rod supports? How much concrete will be needed to fill four 8"-diameter pin-point concrete pier forms to an estimated height of about 80"-inches? How many total bags of cement, gravel and sand (aggregate) will my foundation require? Most importantly, how much will it all cost?"A-Frame Structural Triangle (Theoretical Dimensions):Sides = 16'Base = 16'Angles opposite sides = 60 degreesAngle opposite base = 60 degreesArea = 110.85125168441 sq. ft.Perimeter = 48 ft.Framing:(2) 2"x 10"x 16' girders;(12) 2"x 6"x 12' rafters;(6) 2"x 6"x 8' joists;(4) 2"x 4"x 4' collar beams;(10) 4'x 4' plywood sheets for subflooring;(2) 16' framing braces for structural support against wind damage;(?) 3200-square feet of roof/wall sheathing material for exterior surface areas...*A few questions about the amount of roof/wall sheathing material needed to cover the 3200-square foot exterior surface area: "How much exterior sheathing will I need? How much will it cost? I understand that metal sheathing is preferred in the Copper River Basin region for its snow-shedding ability, so, given everything I've just said, what are my options for the A-frame I recently designed?"My total approach to this whole subsistence lifestyle (i.e. living off the land within a small, confined space) is probably all wrong. I understand that I might need to change my complete "mindset" and adopt a sort of NAUTICAL (or MARITIME) theme with my decor, furnishings and appliances.Since I'm really getting into boats anyway (my one chosen option for escaping the bitterly harsh winters of ALASKA's COPPER RIVER BASIN if all else fails), I feel that marine stoves, composting toilets, and an overall nautical aspect in the "finish work" might help me cope since sailboat cabins tend to be tiny, and I may need to transplant a lot of what I have to my seagoing vessel, "Vera Essie".www.geocities.com/wduncanbinns

Question by Herr VOLKMAR   |  last reply


what is some gear i could use to protect from dying and such while parkouring?

Like i have shin pads and gloves for when i parkour.  but like whenever i roll on concrete i mess up my back. what would be a good way to help protect my back without it being to hot, heavy, or stupid looking? also, some other gear too?

Question by thomasthetomthomas   |  last reply


What is the easiest way to make a cob house? Answered

I am trying to make a cob house. I've got clay, sand, hay, straw, and some concrete. i need to know how to make a foundation and drainage system. I have about a 3 and a half month window to complete this house. I want it to me circular and about 14 feet across. More of a cottage than a house but, still big enough for two small cots, a table, and possibly a dresser and a fire pit.

Question by goatgirly   |  last reply


A Disturbing Store Room

We've just returned from staying with friends in Geneva, where we slept in their (large and airy) basement. Next to the bedroom was the room our friends used as a store room - their nuclear bunker! When their house was built, it was a legal requirement for all homes to have a nuclear bunker.  A stocked, functioning nuclear bunker. The door is steel, filled with concrete.  It doesn't have a lock - that huge yellow bolt and spanner hold the door shut against invaders.  The door on the wall is an escape hatch, in case the house collapses on the main door, and the machinery in the corner is the air filter. The shelves double as beds, and the toilet is a bucket with a lid. I found it fascinating, and, to be honest, disturbing.  It took me two days to "get around" to going through and taking these photos. I grew up during the tense days of US/Soviet nuclear proliferation, when Threads wasn't just a disturbing drama, it was almost a government information film.  I paid attention at school - I knew what nuclear weapons really did.  To most kids, they were a cool way of destroying a bunch of stuff (even more so today).  To me, they were (and are) flatly horrifying, and the stuff of genuine nightmares. I look forward to when things like reduced to the kind of novel feature that ranks alongside "original fireplace" or sash windows.

Topic by Kiteman   |  last reply


Standing (punching) Bag

Hi Everybody I have been boxing for sometime now and have been using a hanging heavy bag. But now I want a little more of kickboxing, so I need a standing bag. But I cant find one here. My "Instructables mind" kicked in and I decided to make my own. I also though of adding a pull bar to it. As in the photo, The black line is the bag stand, and the red one shows the pull up bar. I decided the wall and stand to be 5 feet apart. I may get something up but I thought of getting some professional advice before plunging in. Initially, I planed on digging a hole(about a foot deep) and then using mortar to make a properly round hole so the pole could just slide in whenever I want to use(coz it cant be permanent). And for the pull up bar I could drill a hole in the stand and push the pipe through it and attach a threaded pipe flange to the wall. Should I use pipe or wood. I prefer wood cause its easy to find. People around here have shifted to PVC, so I cant get the pipe from the general sanitary store next door. But I would somehow find it. I need functionality right now. Also if I use the pipe, would filling it up with concrete or mortar strengthen it??? So that's my idea. Any advice is welcome. I need something quick cause I plan to get it done the day after tomorrow.

Topic by Venemot 


How to remodel my front yard garden?

Hi, i have my front yard that I want to renovate so that it is both appealing day and night to anybody who walks in and memorises that moment.  This is the area that has the most traffic everyday at about any time so it needs to be practical, safe and appealing.  I want to design and use any materials but needs to be in the green way as there are much focus on these nowadays and prevent wastage. This is what I have in mind: 12 volt system: A/or many power packs that will provide power to all the electrical stuffs, charged using solar panels and since these will be low voltage it should be safe. Items that would be using 12v would be outdoor lighthing, the power cables, water pump submersible, submersible light.  It would be great to have an electrical plan that would aid however I don't know how to do that. Water feature: Add a biological filter made of concrete for the pond with all its plumbing and also add overflow drain in pond and a small canal to evacuate the excess of water.  Plants:  Concerning the plants some will be moved, cut down or removed completely.  I want a complete mixture of different kinds of plants such As bushes creeping plants etc.  It would be nice to create a plant plan both written and visual as it would aid greatly however I don't really have that knowledge. Other things: I would like to include pergolas and arbours and also allow plants to grow on them such as creeping plants. I want the area to have complete or as much privacy as possible but don't really know specially by hiding the view from above.  As A boundary I want to include fencing and then let creeping plants to grow on them just to get that privacy.  An automatic watering system would be very good such as popup sprinkler, or drip irrigation but an irrigation plan would best be suited but still I don't know how to make that. There should be provision for spaces in adding security cameras that would remain hidden for a certain time period. Finally there should be an Area to store dustbin and also to let clothes dry.

Question by Chamburn   |  last reply