Where can i find nylon?

I am building a vdg for sci fair and i don't know where to look for a nylon roller. also if i use nylon and the top and Teflon at the bottom will that work?

Topic by DELETED_DELETED_kruser495   |  last reply


can I glue nylon sheets instead of sewing?

I want to make a tarp but don't want to stitch the waterproof (pu coated) nylon. Has anyone tried glue or welding with a hot domestic iron?

Question by stillalive   |  last reply


Metal Clip/Mag for Remington Nylon 77?

I have a Remington Nylon 77 and I ordered a clip from a local gunshop, this clip was plastic and after a years use will not hold the bullets in, (if I put in more than 1 bullet they pop right back out)

Question by oldanvilyoungsmith   |  last reply


I bought 6 metres of ripstop nylon for my blimp envelope. What is the best way to seal the edges?

I've tried glue, duct tape, and a bit of heat sealing. It doesn't really work.

Question by ANDY!   |  last reply


Anyone have a good/inexpensive source for small braided nylon, 1.4mm or similar?

 Anyone have a good/inexpensive source for small braided nylon, 1.4mm or similar? I am learning to make nets and can't find a source for decent small cord close to me and the cord that I do have is really slick and a beast to try to work with.

Question by whydoihavetosignup   |  last reply


Does anyone know how to make ripstop nylon water repellent-without the expense of buying a commercial product?

Am trying to construct some dual purpose- outdoor furniture and camping gear-but the only fabric that I have hand is not water repellent. I would appreciate any ideas.

Question by hiddenartist   |  last reply


WHERE CAN I FIND USED FISH NETTING?

LOOKING FOR OLD FISH NET ,NYLON OR COTTON, TRUCK LOAD, PLEASE HELP.THANK YOU JAYBIRD

Topic by jaybird1   |  last reply


help with roller! need help asap

I built a vdg and it works. but since the top roller is AL all it does is produce static electricity until it sparks to the AL on the roller. instead of going to the dome. i have to present it at science fair so i need another roller. i was thinking nylon. so i bought a bed frame roller wheel. but i dont know if it is nylon. so does anyone know if there is any thing i could use that would be at hardware stores or any stores?

Topic by DELETED_DELETED_kruser495   |  last reply


how do i make a bracelet out of climbing rope?

Ecologic has some nice ones that look flat, with nylon covering the ends. Anybody made anything like that, or know of other designs?

Question by    |  last reply


What kind of rope is best for a ballista? Answered

Would Nylon or Polypropene make a good torsion spring?Or would some kind of metal wire work better? By "better" i mean is able to produce the most force or is able to pack the most force into a 5/8"hole (thats the biggest drill bit i have).

Question by meburnfire   |  last reply


I've built a skateboard at school and have a problem with the kick wearing out?

I built a skateboard at school and the first time I rode the varnish wore off the kick. I want to make a kick protector out of somthing like nylon. How could I attach it so I can detash it again. also any Sugestions on how else I could do it? (if i cant do it without glue or bolts please still offer suggestions).

Question by David97   |  last reply


looking for ideas for easy, inexpensive homemade beach sun shade?

Maybe with a tarp, PVC pipe, and some kind of twine/nylon cord?  looking to pick up the materials while on a budget vacation in Florida (staying with family) at the end of May.  Not sure if this will be something I can/will bring on the plane back home.  don't want to cause problems with airport security or have to check a bag.  Really want to avoid being crispy fried.  ideas please?

Question by tdyts2   |  last reply


DIY Boot Waterproofing?

I have a nice ($15) pair of steel-toed work boots that are great, but they aren't waterproof. Being too lazy to buy actual boot waterproofer, I would like to know if anyone knows whether spray enamel (clear coat) would do the same thing. My boots are leather (synthetic, I'm sure) and nylon (I think). I could probably mask the leather off, so it would not be affected by overspray. I was just wondering, in case anyone ha ever done this before. Thanks!

Topic by Bran   |  last reply


leg and arm weights

Will someone write up the plans for a HEAVY-DUTY ankle and wrist weight. I have been searching online for a company that will make custom weighted wrist and ankle weights but there aren't any. I'm wanting to make a 50 lb for the arms and 100 lb for the legs. I'm thinking along the lines of several iron or lead bars strapped together with a nylon fiber or other strong material. I've only ever done projects in high-school, where materials were provided, so I don't really know where to get the materials needed. Please help.

Topic by dhill16   |  last reply


60m floating sea conveyor as customer transportation to/from a deck 30m offshore. Can anyone give me some advice pls?

The aim of this creation is to assist weak/tired swimmers.  The platform (used for watersports) is quite far from shore (30m) and even with lifejackets I don't want anyone getting in trouble or drifting off.  I do have a boat for emergencies but it's too small for regular use   Anyway, I was watching a ski lift and thought that the principle should be applicable (in theory!) to my problem.So far (not very!) I thought I could use waxed nylon rope with floats placed approx every 1.5/2m for people to hang onto - the bit I have no idea about is how to get it all around the mechanisms which power it ( "mechanisms" because I can't remember the names, I really am a beginner so pls go slow!).  Also a bit vague re marine engineering considerations (type of materials etc) and power.  I know I haven't got very far but someone could pls lend me a bit of their brain it would be much appreciated.  Simple and not massively expensive would be a big relief!Thanks again for reading this,Kate

Question by Bulletproofkate   |  last reply