Round Zipper Wallet With Pattern

36,550

223

25

Introduction: Round Zipper Wallet With Pattern

About: Hello. I'm japanese. my craft site http://aoino.com/ https://www.facebook.com/junpei.aoi https://www.facebook.com/aoino.made/

"A greeting"

Hello,this is my first post.

This article has translated from Japanese to English.

Might be difficult to understand.

I'm writing it as easy to understand...

Please listen to google when you do not know.

Sorry I did not write basic method because longer.

If your first work, please look at the your country leather craft tutorial site.

I think surely new discoveries are waiting.

You are lucky that the first time was interested in leather craft :-)

Someday you can in this way. Please always enjoy.

"round zipper wallet with pattern" is using hand sewing and machine sewing.

and using a printer to print the pattern paper.

If you do not have a sewing machine, please made with hand sewing.

Please make a wooden If necessary.

This site's Japanese interface is hard to myself :-<

Let's challenge.

(Sorry, but it is a short sentence from the next page.)

Step 1: Pattern and Parts List

size notation / mm

■pattern

PDF file to printing.

Please download from the web browser.

Note:Custom size at the time of printing.

■parts list

●zipper * 2

(500mm * 1 tape width 30mm)

(155mm * 1 tape width free)

Not determined.

●and see parts list PDF file.

Note:

plan A has 12 card pockets into wallet.

plan B has 8 card pockets and 2 long pockets into wallet.

If you do not have a leather skiving machine, inner parts thickness "1.2mm" → "0.8~1.0mm".

Step 2: Inner Parts Assembly 1~4

Note:

I am writing in Plan A.

(Plan B is write after Plan A)

Adhesive yellow line.

■see photo " inner parts 1 "

sewing like a photo after adhesive from edge of 3mm.

■see photo " inner parts 2 "

sewing like a photo after adhesive from edge of 3mm.

■see photo " inner parts 3 "

sewing like a photo after adhesive from edge of 3mm.(Plan A only)

coin case prepare the parts.

■see photo " inner parts 4 "

sewing at center like a photo.(Plan A only)

coin case prepare the water.

Step 3: Inner Parts Assembly PlanB

Note:
If you makes Plan A, see next page.

■see photo

Sew in the same way as plan A.

I was very tired in the editing :-c

Let's next.

Step 4: Inner Parts Assembly 5~10

■see photo " inner parts 5 "

water on the back like a photo.

and shaping.

■see photo " inner parts 6 "

adhesive like a photo.

■see photo " inner parts 7 "

sewing like a photo from edge of 4mm.

■see photo " inner parts 8 "

measure the width.

180mm...

I want the width to 195mm.

■see photo " inner parts 9 "

Let in the bent 195mm.

195mm=180+x*2

x=7.5mm

bend one side 7.5mm large.

■see photo " inner parts 10 "

inner parts complete.

Step 5: Outer Parts Assembly 1~4

■see photo " outer parts 1 "

make a hand sewing hole from edge of 3mm.

■see photo " outer parts 2 "

zipper adhesive like a photo.

If you do not make a frame, be careful to line.

■see photo " outer parts 3 "

finish.

■see photo " outer parts 4 "

closed.

Step 6: All Parts Assembly 1~3

■see photo " all parts 1 "

inner parts + outer parts

adhesive

■see photo " all parts 2 "

inner parts + outer parts
adhesive

■see photo " all parts 3 "

closed.

Step 7: All Parts Assembly 4~6

■see photo " all parts 4 "

remake a hand sewing hole from edge of 3mm.

■see photo " all parts 5 "

hand sewing.

■see photo " all parts 6 "

hand sewing.

Step 8: Completion

2 People Made This Project!

Recommendations

  • Plastic Contest

    Plastic Contest
  • The 1000th Contest

    The 1000th Contest
  • Battery Powered Contest

    Battery Powered Contest

25 Discussions

0
DustinY5
DustinY5

2 years ago

Is the adhesive done at the edges and stitched through or is it above the stitch line

0
DougA33
DougA33

Reply 2 years ago

It should be at the edges and stitched through. I suggest using 1/8" two-sided tape as it is fast and clean.

0
DustinY5
DustinY5

Reply 2 years ago

Thank you for the reply, I just went with what I figured the best way for doing this was and had great results.

20180108_055727.jpg20180108_055817.jpg20180108_055831.jpg
0
DougA33
DougA33

Question 2 years ago

After the pockets are sewn in it looks like you cut a little notch in the back piece. How deep do you cut the notch?

0
DougA33
DougA33

2 years ago on Step 3

After the pockets are sewn in it looks like you cut a little notch in the back piece. How deep do you cut the notch?

0
DougA33
DougA33

Question 2 years ago on Introduction

Where can I find the original Japanese article?

0
Ed.2
Ed.2

2 years ago

Dear Ali-san - Thank you for posting these instructions! This is exactly what I would like to learn now.
Please clarify, on step 5, how do you attach the zipper to the form before attaching the leather?

0
johnyTNQ
johnyTNQ

3 years ago

please,what is the material used as a frame?

0
junpei.aoi
junpei.aoi

Reply 3 years ago

used "MDF".

https://en.wikipedia.org/wiki/Medium-density_fibreboard

0
ShotyP1
ShotyP1

4 years ago

Hi, can you post on how you sew the zippers on the outer part? thank you

0
junpei.aoi
junpei.aoi

Reply 3 years ago

" frameborder="0" allowfullscreen>

Happy new year.

Sorry to be late.

Have a nice year.

0
junpei.aoi
junpei.aoi

Reply 4 years ago

Hi. Yes can.

What may be the next month?

0
Nonnative
Nonnative

4 years ago

こんにちは、とてもいいinstructable!
日本語はとても下手ですけれども質問があります。さいしょにジッパーがのりでFRAMEに着けてですか。それかれどうやってですか。

ジッパーのこと教えてくれませんか。

0
junpei.aoi
junpei.aoi

Reply 4 years ago

こんにちは。

挑戦してくれてありがとう。直線部分は両面テープ。角はノリでつけています。

後で剥がしやすいようにしましょう。

2016-07-09_032948008_066CB_iOS.jpg2016-07-09_033445206_4921E_iOS.jpg
0
naina12345
naina12345

4 years ago

hi,

Didnt understand the last part of step 7. "remake a hand sewing hole from edge of 3mm." how can i make a hole where there were holes made initially. it will perforate the leather. any advice on how to do this last step?

0
junpei.aoi
junpei.aoi

Reply 4 years ago

Thank you for trying it.

I tried to video.

please watch youtube.

Draw a line on both.

Did you want tips?

Please comment if I have different.

0
MooCowCreations
MooCowCreations

5 years ago

Beautiful piece!!
Can't wait to see what else you make in the future!!

0
junpei.aoi
junpei.aoi

Reply 5 years ago

Thank you for your comment.
Please be expected.

0
germanlad
germanlad

Reply 5 years ago

あなたは素晴らしいです!私はあなたのInstructablesが大好きです。あなたはより多くを行うことができますか? I can talk in English too!?