spinning wires?

I need to run some wires from the axel of my car to my rims, and i need to know how to have it so the wires can spin with the wheels, is there any way to do this?

Question by Sigsaucer647 10 years ago  |  last reply 9 years ago


Whisker Wire

Where can I buy some whisker wire? I am building an OAWR and I cannot find whisker wire anywhere! please help!!!

Topic by crohnsninja 9 years ago  |  last reply 9 years ago


fire wire

Hi if you do poi wid fire wire it looks so kool

Topic by mattadams 12 years ago  |  last reply 12 years ago


Humbucker wiring?

I am rewiring my guitar, and on regular single-coil pickups, there is two wires, but on my humbucker, Three wires come out, a ground, a white and a red. and all my schematics have nothing to say about three wires being soldered. and i have a five-way switch, with eight hubs. i just dont know whereabouts to put the third red wire. please help

Question by ski4jesus 8 years ago  |  last reply 8 years ago


Wiring Amps? Answered

How do you wire amps to speakers and a headphone jack?

Question by NatureBoom21 9 years ago  |  last reply 9 years ago


Battery Wiring?

I have new Li-ion batteries for my mac but i wasn't completely sure on how to wire it up to the old circuitry. I know that "vg" is the ground and the "vp" is the positive. I am assuming "vl" goes to the wire "vl" i dont know what that is thought.  But there is a "vh" spot on the new battery but on the old circuitry there was no wire going to there? Do I solder that wire there? There is also two very thin wires labeled ntc, i can not find a spot on the old circuitry for that is it necessary?

Question by Aaamazzara 7 years ago  |  last reply 7 years ago


Wiring schematic?

Need wiring schematic for old Turf rider 4 golf cart, 36 volt, GE motor

Question by ejredmole 5 years ago  |  last reply 5 years ago


#16 wire

I have a schematic that says i need #16 wire to make an inductor, how do i find that size, what is the translation in mm? if anyone finds some could they give me a link please. thankyou

Topic by andrewlapham2010 6 years ago  |  last reply 6 years ago


Wire Transistor?

How can I make a wire transistor? It needs to work quite well and has to be stable. Please help either with a picture and description or a schematic. Thanks to you guys in advance.

Question by tzq33tdq 6 years ago  |  last reply 6 years ago


Wired Then and Now

When I visited MITERS last month, someone was giving away their entire collection of Wired Magazine. I happen to have a current issue in my bag, and it was fun to compare their relative sizes. It's interesting that I also happen to be wearing a Digg shirt in the picture...

Topic by ewilhelm 10 years ago  |  last reply 10 years ago


Inspiration: wire

Http://www.lobzik.pri.ee/modules/news/article.php?storyid=790L

Topic by lemonie 11 years ago  |  last reply 11 years ago


Microphone wiring? Answered

I have a broken microphone. Its wire is cut  inside the insulation. i want to replace the entire cable. when i removed the plastic cover of the microphone i saw a red and a black wire soldered to it.  Therefore it uses only 2 wires but in the connector it is a TRS one not a TS one. i will also replace the connector.  i am wondering how should i wire a TRS connector which has 3 leads. one being the common ground. but the other 2.  should i short them out and connect the red wire or must I connect the wire to only one lead?  Then if i buy a $0.2 TS connector and i wire it accordingly. will it work? One another question does the microphone device has polarity that is should i connect  positive to positive and negative to negative lead. because there is no indication on the Mic?

Question by ARJOON 7 years ago  |  last reply 7 years ago


joystick wireing ? Answered

Hi , i need to wire a small joystick extracted from a toy remote control. It is life a ps2 joystick. it is working with 2 potentiometre. if you can make a picture It will be very nice

Question by copper tube 8 years ago  |  last reply 8 years ago


Headphone wiring

So I was trying to do some wiring with headphone jacks, and i must be doing something wrong. I have a speaker that the cord ripped from, and I wanted to attach a new jack, I cut off and stripped both wires, so there was a copper one and a colored one, why dont they work when they touch each other?

Topic by Weissensteinburg 12 years ago  |  last reply 7 years ago


Wire to Wireless? Answered

I purchased some XCam2 cameras, They are hard wired. Due to the need where to locate them, I would need them to become wireless. This is a great site along with some great minds. Thank you all for your input.

Question by Boriqua 9 years ago  |  last reply 7 years ago


Magnet Wire

Cutting open transformers (you might call it an adapter, or charger) yields a good quantity of re-usable magnet wire. Motors don't seem to be a very good source, since the windings on those seem to be saturated in varnish to glue em together. Apparently, vibration is more of an issue in the motors, so they make the windings solid. This might be different in little hobby motors. Dunno.

Topic by Toga_Dan 4 years ago


nichrome wire

I got some nichrome wire off eBay, and it works great but when I connected it to a 9 volt battery it barley got hot, then I attached it to 4 x AA batteries and it got red hot. why is this? I don't understand because the 9 volt gives out 9 volts(duh) , but the 4x AA batteries only gives out 6 volts.

Topic by Jordo 11 years ago  |  last reply 11 years ago


Wiring help!

I have an 8th grade science class (I'm the teacher) that I would like to have construct underwater vehicles.  The kids will be using 9v batteries, switches and assorted other materials.  Does anyone know of any good books/articles that explain the basics of wiring, electricity, motors, switches, etc.  that I can have the students read to get a good base of knowledge in the basics of electronics? Thanks!!!

Topic by mashmtz 7 years ago  |  last reply 7 years ago


Disconnected Wires

So I'm working on a heart sensor, and pulled out the wires. I think I can fix it with a  little bit of solder, because after 20 or 30 minutes of negotiating, i can usually re-establish the connection to the sensor. But I tried just now, and it isn't working. Help??

Topic by kate1171 4 years ago  |  last reply 4 years ago


Wiring Question

Ok, I recently purchased a Go-Ped for practically nothing, and I really, really, really want to fix it up. I want to mount a couple of LED powered bicycle headlights on the front, and a tail light on the back. However, I want to be able to turn them all on and off via a single switch, mounted to the handlebars.I know very little about wiring, but I do know that most bicycle lights require physical pressure to power them on or off. Maybe there's something that can go between the batteries and bulbs?Any input you can provide would be fantastic!-Ryan

Topic by ryry214 10 years ago  |  last reply 10 years ago


microphone wiring?

Ok i was wondering if i took a microphone that was real cheap from walmart and take the male part off the end of it and put a female part so that way i can plug in a dual male sided cord to it and then to my computer, more or less im wondering, can it work like that? and then i was wondering if there is a program that when i plug the mic in that it works like plugging a guitar into an amp, as in it plays the input to the computer outloud without being in playback from a recording

Question by ClemensY290 9 years ago  |  last reply 9 years ago


Wiring question?

Hi everyone. Long time visitor of Instructables, made a few items I've seen and my most recent project was adding a star power pedal to my guitar hero controller. I bought a audio extension cable with a male and female jack, 1/8th size. I cut the cable about six inches from the female end. I stripped about an inch, inside was a bundle of copper wire wrapped around a clear insulted wire. I twisted the exposed copper wire and tinned it, I stripped the clear housing and twisted it, tinning them as well. I tinned the exposed wire to the GND, and the clear to Select. Positioned the jack and everything went well. I took the male cable, connected it to momentary switch and connected the male cable to the female jack. Turned on the system and controller. Got star power and hit the switch with no response. I'm very confident in my soldering and know I did it correctly, so I was wondering: 1) Are these kind of cables capable of doing what I intend? 2) Maybe the GND or the Select button are shorted out on the board of the controller? Thanks for any help everyone!

Topic by Mercenary Wubby 10 years ago  |  last reply 10 years ago


wiring help

Im working on a fireworks show and i just bought 25 toggle switches and led's from a garage sale for 5 bucks.. never opened still in packaging. how would i wire all this up to show when its armed a light would show on each channel.. im using this thing to ignite the bigger fire works (2 per switch)... i got around 360' of extra red insulated wire laying around from the shop i work at in the summer becasue they are throwing/giving away. any advice i also got a few rca and 1/8' male and femail jacks and a few push buttons from salvaged things... could i also use the thingys from cameras that put out 330 volts i have a few of those. you can contact me on meesenger also at:deer_hunt05@hotmail.com

Topic by pyroboy5 11 years ago  |  last reply 11 years ago


Dollhouse wiring

Hi All. I'm a believer in the idea that anyone can do anything with a little info. But I'm in need of a little help.  I'm building a dollhouse for my niece and would like to add a little higher-tech slant (she won't be playing with this for a few years yet...)  I would like to add LED lights (which I will make but just have to wire for at the moment), a flicker fireplace and a door bell all on wall mounted pushbutton switches.  Feel free to suggest anything else that might be cool for a kid... The whole system will run on a 12V adapter but since I need to wire this NOW so I can continue to build, I need a drawing or schematic of how to do it. I've attached a pic of the house and have been pulling apart some of the small flicker Tealights to kitbash into the fireplace.  I have a number of white LEDs with which to make the lights but they don't have to go in right now.  I know I'll need some resistors - where do I place them?  Hide them in the walls?  On each switch? Anyways - any help is so appreciated.  She'd never get anything like this unless I made it for her - I just want it to be so cool that her brothers are impressed! Tbird

Topic by Golftester 8 years ago  |  last reply 8 years ago


Help with wiring

I have disassembled an old vacuum cleaner that runs on 240v/5amps/1200w. I wanted to obtain the electric motor that should perform at 1.5 horsepower. As I was taking it apart I forgot how the switch leads were originally configured. I want to give the motor a test run but I don't want to hit the fuse in my house so I was hoping someone can help me plug the switch in the normal configuration. What order do the brown and blue plugs (that comes from wall plug) fit into the switch? And what order do the blue plugs (goes to motor) fit into the switch? A silly question really but I am new to working with electronics.

Topic by Tyoon 6 years ago  |  last reply 6 years ago


Wiring help

Hi guys I am need of some advice and help if possible, I will try and explain as clear as I can. I have a lockup which I have modified to use locking bolts on a motor and I have a swipe card reader and pcb which when swiped it fires the output to power the motor (6v) which works perfect for 6 seconds of the locking bolts going in and out. I am looking for a way so when the locking bolts go to the locked position it hits some kind of limit switch and stops there (which I have done in the past) but then I want to be able to swipe my card to open the bolts and when it gets to he open position it hits another limit switch and stays open until I want to swipe and close the locking bolts. I don't want this to be timed I need this to stop on open and closed position but able to operate when either is pressed, Can this be done in anyway?

Topic by sherpin2000 7 years ago  |  last reply 7 years ago


Wiring welder in the Philippines? ( 3 wire to 2 wire )

AI have a millermatic 211 which is a multi-voltage welder which I will be bringing to the Philippines. The adapter plugs are 5-15p (120v), and 6-50p (230v). Philippine electricity mains when I live are 220v single leg, with neutral. I am adding ground to both the Main panel and sub panel when I arrive, as most residential homes with a 2 wire system do not have them installed. According to the welder schematic  6-50p adapter configuration shows white, red, and green (ground) so goingfFrom a 3 wire US to 2 wire Philippine system is it proper to wire L1 to red, neutral to white and green to ground? 6-50 receptacle does not seem to incorporate a ground in typical installations????

Question by Antonioo35 1 year ago  |  last reply 1 year ago


is a brown wire the same as a black wire?

Usb cable. and no there is no black wire

Question by DJZizo123 6 years ago  |  last reply 6 years ago


is hookup wire the same as electric wire? Answered

Question by RobotBoy740 9 years ago  |  last reply 9 years ago


4 wires fan to 2 wire

Hi guys, i need your help! I have an Enermax 12cm fan (EB122512H), i need to plug it to a 12v DC power supply but i don't know how to wire it; The fan has 4 wires (yellow, black, white, red) but the power supply has just two wires. could you help me?

Question by MichelS7 3 years ago  |  last reply 1 year ago


i have wires that plug into pcb's the wire is a silver coloured wire that is non magnetic, what is it made of? Answered

I have the wire from re cycled dvd players and they are fine thin wires when stripped from the casing they are not copper as i expected, but i'm not sure what they are made of the wire is not magnetic I want to recycle the wires but i need to know what they will be made from

Question by diggerevans 8 years ago  |  last reply 8 years ago


i need desperate help with this transformer for a capacitor charger? Answered

okay.. heres the dealio. I DON'T KNOW HOW TO USE THIS BLOODY THING! okay, i have this to charge about 15-20 200v 470uF capacitors and the multimeter i have has a capacitance option but idk how to hook the capacitors at the same time to even charge them right and be able to immediately fire the coil gun when they are full.. so basically i need to figure out how to hook this transformer to about 15-20 capacitors, charge them all simultaneously, then when they are charged, fire the coil gun. 50/60Hz 8.2A 900W 120V Model:RCD-UPS1500D this is a computer UPS by : ULTRA the 2 batteries are 12V 28W

Question by egammoc 7 years ago  |  last reply 6 years ago


2 Wire Servo on 3 wire reviver? Answered

How can i wire a 2 wire servo into a 3 wire receiver I'm talking about the motor type, The reason i need to do this is because i need to get a cheap RC car on good radio gear

Question by Daniel Deacon 7 years ago  |  last reply 6 years ago


subwoofer installation? red wire, blue wire?

I need help with a car subwoofer, i have a friend whos red wire went, and doesn't have a power antenna akak a blue wire. his red wire went, its a 2000 buick and the cars are notorious for that issue. i have it on a switch for the 12v and i have a jumper from the 12v to the remote so when the switch is flicked the remote and 12 v are powered. is there an alternative wire to connect the remote to besides the red or blue?

Question by slimguy379 9 years ago  |  last reply 8 years ago


HOW TO Basic electric wiring ? Answered

Hi community , i need help to wire my small project  and its about a water dispenser, but with the big water bottle(22liters) is on the floor, so there is : a water  pump(to pump water to a small tank on the water dispenser or cooler),rocker 3 position switch, floatswitch, electric transformer 220-12v.  WHY? a 3 positon switch  the pump works on 2 different modes _ the first continuous mod that stops only when the small tank is fully filled ( wired with the  floatswitch ) _ the second mode is : just a simple working pump with no stop ( not wired to the floatswitch ) So TAKE A LOOK ON THE ATTACHED PHOTOS PLEASE LET ME KNOW HOW TO WIRE THE ROCKER 3 POS SWITCH , And if there is a wiring diagram that will be the best of the best !!!     Thank you, ""HELPFUL community""                      

Question by vwtm2006 4 years ago  |  last reply 4 years ago


What is the best way to connect small copper wires?

Not best as in most expensive, best as in least likely to short or detach. The easier, and/or cheaper, the better. What I mean by small wires is the copper wires you would in hobby d/c motors, or buzzers. thanks :)

Question by rocksalt2342 9 years ago  |  last reply 9 years ago


Disposable camera flash and a EL sheet or wire - Will this work?

If we replace the capacitor of a disposable flash with a EL sheet or wire, will it glow? (this is since EL wires can be hooked up straight to the main voltage, which tend to use over 200volts. A camera flash that uses a capacitor that charges at a high enough voltage might be good enough for powering a EL sheet.) anybody willing to give this a shot?

Topic by akimbo m 9 years ago  |  last reply 7 years ago


can i drive the el wires from the mains of our house?

 

Question by samsulrana 9 years ago  |  last reply 4 years ago


what should be the inverter voltage to drive 50 metres of el wire?

 

Question by samsulrana 9 years ago  |  last reply 9 years ago


How do you trace electric wires in a wall, without tearing the wall apart?

I have a wall switch that I can't figure out what it is to. I have taken the front plate off and the switch works. There is electricity on the wires leading out of the box when the switch is on. Is there a way to trace the wires through the wall?

Question by Juliusredwings 9 years ago  |  last reply 2 years ago


quickest glue?

Quick glue led wires into under cabinet corners   what to use

Question by designmore2 3 years ago  |  last reply 3 years ago


Wire problem help?

Hi all, I have been trying to extend my laptop LCD wires to move it away from the laptop,as it only has about 15cm reach at the moment. It is very hard to do as the the wires are very tiny.It was going ok until I ran into a problem with the last four wires.The last four wires are small enough as it is but when I riped off the ends I found that there are two wires inside and some metal wire stuff around them. My problem is i'm not sure if the metal stuff around the two wires (white and purple) is a wire aswell or if it's some sort of protection layer? Another question I have is,will using bigger wires to extend the little original wires cause any harm to the signal? Here is a couple of pics to help. Cheers for any help!  

Question by luther303 6 years ago  |  last reply 6 years ago


Are these silver wires important?

I'm making a USB wall charger with a usb cord I found in my desk and an unused cell phone charger. I cut off one end of the USB cord and took the plastic stuff off of it and there were silver wires along with the red, black, green, and white ones. Are they important or should I just cut them off?

Topic by Sunbanks 10 years ago  |  last reply 10 years ago


Infrared Sauna wiring?

Well, I bought a used infrared sauna the other day for real cheap because it "just stopped working all at once". Figuring its just a fuse or something, I took it. Well now I cant figure it out for the life of me.What seems to be the problem is that no power is getting to the primary transformer. That would be on the second small circuit board to the right. It is getting to the secondary transformer fine. Heres a pic of whats goin on. Those things on the sides are fuse holders, (no not burnt out).

Question by LiquidLightning 7 years ago  |  last reply 6 weeks ago


Some strange wires

Hello everyone I have a problem and I am looking for some solution. I was doing some repairing today found my old headphones with microphone that lost contact on small circuit board that use for on/of mic and reducing volume of headphones. So I decided to cut that circuit out and just solder 2 ends together but that I fond out that there is some strange wire  coming out. After I remove isolation there is some colored wires made out of some strange material. It is not conductor (I tried to attached but nothing happened and checked if it is conductor- not). So I ask you do you know how to solder 2 ends (and I cannot make mistake because all wires that need to be soldered are same color) if there is no conductor :O ??? (well maybe there is but I cannot find it ) If you know please help. Thanks!

Topic by lodcoek 7 years ago  |  last reply 7 years ago


Which wire is which? Answered

Ok, I have this solar panel I was given, and a knex motor without a battery box, and In need to test which wire is positive and which is negative on the solar panel. I am no good at electronics, though I have done soldering before. I was wondering, how do I test to see which is positive an which is negative on the panel? I hope to join it to the motor to have a very powerful, eco-friendly solar model.

Question by TheFoofinator 7 years ago  |  last reply 7 years ago


wire and bead tree

wire and bead tree tutorial

Topic by halla 8 years ago  |  last reply 8 years ago


wire electric in house?

Question by acherryl 9 years ago  |  last reply 9 years ago


EL Wire Needed

Is anybody giving away free EL Wire?

Topic by Loganbo 7 years ago  |  last reply 7 years ago


ni-cad wire

Does anybody know where to get some Ni-cad wire ?

Topic by joe12 10 years ago  |  last reply 10 years ago