is there a stretchable thin polyurethane or silicone I can use on thin nylon mesh fabric for theatrical wig?

I would like to make my theatrical wig more durable and would like to add a thin layer of stretchable silicone is this possible?

Asked by 9 years ago


Which adhesives are either water or polymer based? Answered

I am trying to make this and it suggests either a water or polymer based adhesive, but I can't find which ones qualify. Alternatively, what adhesive would you suggest I use?

Asked by bomberman3 9 years ago | last reply 9 years ago


How do I thin out 2-part epoxy?

I'm wanting to make some micarta-like material, using two-part epoxy and paper. I've done a test run, and the material was rigid after it had cured for a few days, but didn't cut like I hoped it would, because the epoxy didn't penetrate the paper. Part of the issue was that the paper was coated, but I'd also like to thin out the epoxy some so that it will soak into the paper better. I'm inspired in this endeavor by these two instructables: https://www.instructables.com/id/How-to-make-homemade-micarta/ https://www.instructables.com/id/Mokume-Kireji-DIY-Woodgrain-Composites/ The epoxy I'm using is 3M Scotch-Weld DP-190. The label says it contains epoxy resin, polymeric diamine, kaolin, and carbon black. The complete MSDS is here. This is what I'm using, because it's what I have. Got a case of these two-tube dispensers cheap at a yard sale. :-) So, what can I use to make this more liquid? Right now the consistency is a little bit thicker than honey. It doesn't spread out when applied to paper, and doesn't soak in at all. My limited knowledge suggests that toluene, listed on the MSDS, might work, but I'm hoping for something a bit less volatile. I'm aware that whatever I do is likely to extend the curing time, but that's not necessarily a bad thing.

Asked by yoyology 6 years ago | last reply 2 years ago


glue gun trigger not "gripping" the glue?

When I push the trigger on my dewalt glue gun the trigger moves but doesn't "grip" the glue to push it forward. Any ideas how to get it to grip the glue?

Asked by dvoss3 12 months ago | last reply 11 months ago


What is the difference between PVA glue and Elmers glue?

What is the difference between PVA glue and Elmers glue?

Asked by threadbare 9 years ago | last reply 3 months ago


my glue from my glue gun comes out yellow is this bad?

Asked by ikeike40 8 years ago | last reply 8 years ago


How to glue silicone to leather ? ?

Hi I need to glue silicone to leather, i've tried to glue it with various glue but it always comes off... is there any known way to glue very good , silicone to leather ? thanks! :)

Asked by giorgiomartini 4 years ago | last reply 4 years ago


How glue can be used ?

Need Glue for my next project, please suggest glue solution. Thanks!

Posted by RajenderK4 2 years ago | last reply 2 years ago


How to glue silicone to leather ?

Hi I need to glue silicone to leather, i've tried to glue it with various glue but it always comes off... is there any known way to glue very good , silicone to leather ? thanks!

Posted by giorgiomartini 4 years ago | last reply 4 years ago


How non-toxic is CA glue? Answered

Hi gang, I know CA glue (Krazy glue, Cyanoacrylate) is solvent based, and inhaling the solvent is bad for you, but how safe is it after the glue cures? As I understand it, after curing the glue is basically a plastic.  Can I use it in a baby's crib (Assuming it's allowed to cure)? Thanks!

Asked by Morgantao 4 years ago | last reply 4 years ago


Is there any type of glue made for styrofoam?

I'm working on a school project where I have to layer pieces of styrofoam but all the glues I have tried (hot glue, spray adhesive glue) have corroded the styrofoam way to much. Is there a special glue that will not eat away at it? Thanks!

Asked by DELETED_afw11 9 years ago | last reply 1 year ago


What is the best glue for ceiling applications?

Asked by wheelbme 8 years ago | last reply 8 years ago


How can I glue plexiglas?

Asked by fastrack777 9 years ago | last reply 9 years ago


Which glue??

I want to attach pieces of tinfoil on chicken wire for my project. Which glue to use and it will be outside!? Thanks 

Asked by ChristinaT45 2 years ago | last reply 2 years ago


i need to glue aluminum foil to presswood. ..what glue should i use?

I need to glue aluminum foil to presswood. ..what glue should i use?

Asked by polarbyrd 7 years ago | last reply 7 years ago


how to repair hot glue gun? Answered

..because it doesn't work. the gun is hot but it doesn't squeeze out the glue anymore. the trigger is hard and 3/4 of glue stick is still in the tube.

Asked by Karletto555 8 years ago | last reply 10 months ago


How can you remove krazy glue from plastic? Answered

   One of my model rocket fins was broken so I used some Krazy glue to fix it, but some of the glue got on the piece that screws into the bottom to hold in the engine so now I can't get the engine back out. -__- so I need to know how to "unglue" the two pieces. thanks every one. ThePunisher'sAprentis

Asked by Everett_McKinley 7 years ago | last reply 7 years ago


quickest glue?

Quick glue led wires into under cabinet corners   what to use

Asked by designmore2 3 years ago | last reply 3 years ago


How do I glue sand to styrene

Styrene glues

Asked by MarkB711 7 months ago | last reply 7 months ago


hot glue damaging any part on a disposable camera circuit?

Such as the transistor or other devices it is a small hot glue gun

Asked by xproplayer 9 years ago | last reply 9 years ago


What is the best glue for gluing glitter on plastic?

I was working on a project and i needed help. What is the best type of glue to glue glitter on plastic. What is the best sealer? I was thinking mod podge but i was wondering if i can use it for the glue and sealer. Any advice?

Asked by Ilovepandas123 2 years ago | last reply 2 years ago


Elmers Glue + Super glue =?????

I was making some stamp glue where i mixed some Elmer glue and vinegar. but wanted to see Wat happens when i mix Elmer's glue, vinegar, and super glue. like in 10 seconds the solution turned into a rubbery solid which took the form of the container. can any body tell me why this happened. it held its shape and slightly reminded me of molding silicone. it wasn't sticky and came out of the plastic cup easily.

Posted by chrischavez 10 years ago | last reply 2 years ago


gorilla glue

How strong is gorilla glue? I am trying to make my knife stronger by putting some gorilla glue on the tang of my knife and putting it into a wooden handle. Would this make for a super strong hold?

Posted by Pat Sowers 11 years ago | last reply 11 years ago


What type of glue is used in converse shoes? Answered

What type of glue is used in converse to glue two layers of canvas together, and the canvas to the rubber sole? Thanks alot for all answers :)

Asked by Lizander 8 years ago | last reply 8 years ago


Is it possible to use hot glue as an adhesive for LTD stirling engines? Answered

Is it possible to use hot glue as an adhesive for building low temperatue difference (LTD) stirling engines? I was wondering because I do not want to buy epoxy or other expensive glue. Will I be able to use hot glue, or will the glue melt from the heat of a cup of boiling water? 

Asked by Zippo1234 7 years ago | last reply 7 years ago


Is there any way to make hot glue more elastic?

I'm planning on casting some objects out of hot glue with a mold, but hot glue is a bit too stiff for the result I want. Is there anything I could mix with the melted hot glue to make it more elastic?

Asked by montso 7 years ago | last reply 7 years ago


what kind of glue for this project? Answered

I have to glue a little mirror on a speaker (cardboard cone) and since the speaker will be moving with sound (lots of vibration) i wonder what kind of glue i should use

Asked by pbergeronronronron 7 years ago | last reply 7 years ago


How to dissolve wood glue of a brush? Answered

After I used a brush to apply Gorilla© wood glue I forgot to clean it and, I need to know if there is a solvent that can remove the wood glue of the brush.

Asked by blkhawk 6 years ago | last reply 10 months ago


Is there any way to glue plastic to fabric?

I want to glue a plastic ziplock bag to cotton/spandex fabric, is there a particular glue that will do the job or any other method anyone can suggest?

Asked by nigelwclifford 6 years ago | last reply 3 years ago



Glueing Plastics Together? Answered

When I say plastics, I mean more specifically, LEGOs. I'm glueing them together because I'm trying to make LEGO headphones, so I would need something permanent. I've heard people using cyanoacrylates and clear plumbing glue (anyone heard of Oatey?) I thought about using hot glue, but I'm not sure if that would give me the bond that I'm looking for. Would Gorilla Glue work too? Or would it be a bit of an overkill? I simply need a glue that will hold the LEGOs through enough wear-and-tear to last, and no discolouring of the pieces. And when I glue, should I glue the sides of the pieces together, or put glue around the dotted studs on the tops of the bricks? Any other glues or advice that you could enlighten me with would be greatly appreciated. :)

Asked by Justin Lam 8 years ago | last reply 8 years ago


How to glue patch?

I want to glue several patch to my sons backpack but dont want to iron then. Can i just use a good glue to set them? Thankyou

Asked by 9 years ago | last reply 9 years ago


How can I remove gorilla glue? Answered

I got this glue on my hands and ipod and i'm wondering if anyone knows a way to remove it.

Asked by DoctorDv 6 years ago | last reply 2 years ago



Which Glue/Adhesive Should I Use With EL Wire? Answered

Which Glue Should I Use With EL Wire? I want to glue some EL wire to glass, Which adhesive should I use? Which ones can you recommend? It would also be the best to use a clear adhesive My preferred ones are: Super Glue (cyanoacrylate) Hot Glue Clear Silicone

Asked by Yonatan24 3 years ago | last reply 3 years ago



Adhesive for gluing plastic bead on wood ?

What is great adhesive for gluing plastic beads on wood ? Epoxy glue? I also thinked super glue. I would like to glue plastic bead center of wooden pendant. Is anyone done this before?

Posted by DeathSuperMario 3 years ago | last reply 3 years ago


Has anyone added pigment (black) to hot melt glue to "hide' it in assembly of components??? Answered

Need hot melt glue in colours.

Asked by kdkos 9 years ago | last reply 9 years ago


hot glue molding?

Is there any suggestions to the best way to mold hot glue like you do with clay and also adding food coloring to make it colorful?

Asked by Caroline Kershaw 9 years ago | last reply 8 years ago


Hot Glue Gun stuck

I Have been using a glue gun for quite some time but nearly 5-6 days ago, while i was on a project , i left it on/forgot to switch it off and went to sleep...........when i checked it in the morning not enugh glue had melted out, that was weird, then when i pressed the triger the glue would come out in cilindrical pattern and is not hot at all..........i even tried to push the glue out of the nozzel but its stuck in it......also the stick is a cheap one(bad quality) the 2 possibilities that r possible are- 1) the glue stick sucks  2) glue gun is busted

Asked by rkun2 2 years ago | last reply 2 years ago


I need glue recipes to use with my papercrafting projects

I discovered the glue I was using was not holding my papercraft beads and other stuff together. I need a strong glue to hold them together. I need a recipe so I can make enough of it myself and not have to skimp on glue. Anyone have a recipe for strong glue that can be brushed on the paper and hold long after the project is finished?

Asked by cherlane13 9 years ago | last reply 9 years ago


Does araldite glue damages circuit? if yes,what glue or resign you cover your circuits with? Answered

I ones tried covering my circuit with araldite. Eventually it stopped working(as the glue dried.it started to slowly malfunction. What glue do Americans use in indestructible like-  https://www.instructables.com/id/Resin-Clock/

Asked by Suraj Grewal 5 years ago | last reply 5 years ago


What is the best glue for plastic to leather?

Last winter I ripped the plastic sole from my skiing boot, and I would like to reattach it. It looks like it was originally held on by glue, and that is what I thought I should use.Any idea on what type of glue I should use for this?

Posted by Sedgewick17 11 years ago | last reply 8 months ago


Metal on Metal Glue

Is there such a thing? What's it called?

Posted by Weissensteinburg 11 years ago | last reply 9 years ago


foot pedal controlled glue gun?

I would like to have a glue gun mounted on a stand and controlled with a foot pedal so both hands are free. Any ideas on how to do this?

Asked by baker_eliz 2 years ago | last reply 2 years ago


Do repositionable glues stick to the original surface?

I want to treat a plastic sheet with some glue, so it would create a Post-It like surface. I'd like to have this (original) surface sticky indefinitely, and to have anything I attach came off clean later. Is that how these repositionable glues work? Will they stick permanently to the surface they applied to first? Or there is no "original" and "other" piece, and some of the glue will transfer eventually? Is there a difference in repositionable adhesive spays and removable/restickable glue sticks in this sense?

Asked by shinjin 5 years ago | last reply 5 years ago


Seal Glue Glitter on Plastic?

I bought some fancy reusable clear plastic cups and I applied some glue glitter on them.  Unfortunately, the dry glitter glue scrapes off, so I'm wondering Is there a sealant that can: 1) keep the glue from being scraped off, 2) dries clear (the glossier the better), and 3) is non toxic?  Tried Mod Podge spray sealer, Glossy Accents, even finger nail polish.  Any suggestions?

Asked by drc536 3 years ago | last reply 2 years ago


What glue can I use to stick silicone to plastic? Answered

Plastic is easy, lots of stuff sticks to plastic, but the only thing that seems to stick to silicone is more silicone. Hot glue, super glue, Elmer's glue, Gorilla glue, and liquid steel epoxy all fail. Any suggestions? Maybe something marine related? (Background: I used some left over silicone molding compound to make a comfy handle, but it doesn't want to stay on.)

Asked by Grathio 9 years ago | last reply 8 months ago


Can you help me make a waterproof, non toxic glue? Answered

Hello, I'm working on a project and I really need to make a glue for gluing powdered seashells (CaCo3 basically), this glue has to be non-toxic, waterproof and moldable. Please help me!!!!!!

Asked by OnatA2 1 year ago | last reply 1 year ago