inverter

I am making an inverter whivh converts 12 V dc to 230 V ac i am using 2 33 ohm resistor of 1 watt to connect the load on transformer whenever i switch on the ckt the 1 watt resistor are heating to much and multimeter does not show any voltage i am using 12 Volt dc 2.5AH battery as power supply what is the problem

Posted by AbhishekR2 3 years ago


need circuit diagram for a sin wave inverter?

Good day honorable members pls can anyone help me i want to build an inverter and i need a circuit diagram for an 50Hz 24v to 220v sinwave inverter. Pls can anyone suply me with an circuit diagram for an 2KVA and a 5KVA inverter pls pls help me thank you in advance

Asked by rahvin1223 6 years ago


can i test a 90w inverter with a 1amp psu and my load is a 13w light 110v? Answered

I have tested an inverter with a cable modem psu but not lighting the light, is it due to PSUs 1amp rating or simply Inverter is faulty, I don't own a car or Battery for that matter yet.. 90w inverter 13w light 1 amp power supply.. thanks

Asked by celalboz 7 years ago



How to biuld a sine wave inverter?

I need to build a sine wave inverter but i do not have the schematics.I need an assistance in this project.I can build a square wave inverter but it makes noise in the fan and does not surport my 29 inch television causing it to have frequent low current  problems.I heard that sine wave inverter is more efficient for home appliances.Please can some one help me with a simple diagram to build my own efficient sine wave inverter.Thank you all.

Asked by 8 years ago


Is it possible to run a power inverter in reverse? Answered

I'm curious as to whether supplying power to the ac out side would result in the dc in side putting out power or the board burning out.

Asked by acetyleneblues 5 years ago


i have a blackand decker electromate 400 i took it apart for the inverter but the rockerstwich is broken

How to i jumber it to on so i can see if the inverter works

Asked by jlc30 5 years ago




How do I make a 240volt inverter from a microwave transformer

Good enough for power tools I saw one on the net somewhere and can't find it. I got a microwave from the tip but it was too good and so it has a new life in the kitchen.

Asked by tezzz 8 years ago


what will happen if i give dc 12v and 5 ampere to 2000watt inverter , how much ac ampere should it produce ?? Answered

I now what inverter does it convert dc to ac , i also know that it can convert dc 12 volt to ac 120 -110 volt but  the thing from which i m confused with is that what will happen to the ampere for example i have a 12 volt 5 ampere battery if i plugged the battery to 2000 watt inverter should it produce 2000 ac watt with just 12 volt and 5 ampere battery or i have to give more dc ampere to the inverter................ means can inverter    convert dc less volt to ac high volt  and  with also convert dc less ampere to ac high ampere   or will it convert  dc low volt to ac high volt without changing the dc low ampere and need more dc ampere or will it convert dc low volt to ac high volt with decreasing the dc ampere....

Asked by MuhammadK19 2 years ago


hi, i am in ghana and interested in building this remarkable inverter. Answered

I have been following the question and answer section and had most of the points. my questions are 1. what is the use of T1 and 2. how do u program the IC

Asked by aakareng 5 years ago


How to make a 6vdc to 200vdc converter?

Hello, i am a bit confuse about how to convert 6v dc to 200 v dc having a least power output of 25watts. is it possible?

Asked by ubdussamad 4 years ago



5000 watts power inverter

5000 watts power inverter with the circuit diagram using SG3524

Asked by santos4eva 7 years ago


how to build an inverter

I want to know how to build an inverter upto 5kva

Posted by segge 3 years ago


connect power inverter to car battery?

How do i properly connect a car battery to my 2000w power inverter

Asked by chainsaw0068 7 years ago


What is the simplest yet reliable inverter (NOT) gate setup?

What is the simplest yet reliable inverter (NOT) gate setup, in your opinion, for feeding its output to a 555 timer's trigger input?

Asked by raftor 4 years ago


can I use AA battery bank to power an inverter (3000ma 12v)? Answered

Can I use AA battery bank to power an 50w inverter (3000ma 12v)?

Asked by celalboz 8 years ago


Connect power inverter's AC output to my home AC power

How can I connect a DC power inverter's AC output to my home AC power without a transfer switch so the inverter does not get damaged.  Connect it directly or with what ?

Asked by jehardy 8 years ago


MANUAL OF POWER EXPRESS INVERTER/BATTERY CHARGER

Could any body help me with the operation manual of power express inverter?

Asked by austinbby 6 years ago


How to make a inverter and battery of our own?

I want to make inverter and battery at home.If we make at home whether its cost will reduce when comparing with outer outlets.Please tell me in brief if possible.

Asked by anilr13 6 years ago


how do i make a laptop inverter work?

hi i am wanting to be able to run a laptop inverter off a few batterys the inverter looks like the one in this instruclible https://www.instructables.com/id/How-to-Fix-an-LCD-backlight-power-Inverter-Using-/step8/Bridge-the-fuse-AT-YOUR-OWN-RISK/ i was wounderin what cables i would need to put power on ? i an not wanting the screen to work, just for the back light to glow, please help

Asked by rug 7 years ago


can a dc to ac power inverter mess up a car?

My family is going on a long trip this thanksgiving and I wanted to use a power inverter that i have to power a portable dvd player(actually its an old laptop with a dvd drive) on the trip (its battery is toast and I have no car charger) my mom thinks that the inverter will find a way to mess up her Toyota minivan and won't let me plug it in is she right? can a power inverter mess up a car?

Posted by clasic_traveller_diehard 9 years ago


IS 12V SUPPLY FOR PWM CONTOL INVERTER IS FROM OUTSIDE SOURCE & WHERE TO CONNECT IT'S NEGATIVE(OF OUTSIDE SUPPLY )?

IS 12V SUPPLY FOR PWM CONTOL INVERTER COMING TO THE I.C 7808  ,APART FROM TRANSFORMER, IS FROM OUTSIDE SOURCE & WHERE TO CONNECT IT'S NEGATIVE(OF OUTSIDE SUPPLY )?

Asked by ER. ARJUN SHARMA 6 years ago


What inverter should I use to tie in 3 60 watt panels into an outlet? Answered

I am trying to find a fairly cheap inverter to tie my panels into my home. I am planning to add a few more panels in the future. I am not going to add a battery bank. Thank you.

Asked by pokey02 9 years ago


inverter on a camera flash

Ive been studying the intertubes for a bit now and I cant seem to find an explanation on how a disposable camera flash works in detail. I mean I understand that it runs with two transformers, one at 300v output to charge the cap and the other to help discharge the payload through the xenon bulb run at 2000v output. but a transformer doesn't work with out a pulse or rapid continuous change in voltage. so how is it inverting to ac or am I missing something stupid

Posted by snowfox222 4 years ago


can i use a 110v inverter connected to a 2000w travel converter to get 220v and power a 220v fridge Answered

I might need to do this when there is an electric outage, can we connect an SLA to inverter (110v) to a converter people use when they travel to 220 v countries?

Asked by celalboz 8 years ago


i need to use my 60w 127 vac sodering iron in my car as in 12 vdc so i need a cheap easy to make inverter any ideas?

Later i would also like a inverter that could handle a 950W 127VAC angle grinder also cheap and easy (ish) to make

Asked by cassiorichiniti 9 years ago


Can I use MJ3001 in place of 2n3055?

I want to build this inverter circuit, it uses 4 2n3055 transistors. Can I use 2 mj3001 transistors in place of that?

Asked by Ankan Nayak 5 years ago


Grid tie solar inverter power from a fixed voltage source?

Hello there! We have a 4Kw solar system installed at our home. We also happen to have 2 seperate circuits (ie 2 electricity meters). Annoyingly the solar panels are installed on the circuit that we don't use much electricity off so most of the generated electricity flows into the grid and (I know it's selfish) we don't benifit from it at all. There happens to be one lonely socket next to the solar inverter that is powered off the other electricity circuit and I'm fairly sure that the two circuits are on different phases. This is what I wanted to do and I was hoping someone might be able to validate this: I install a 240v AC to 24v DC converter (PAK650-24) and then an inverter to convert this back to 240v AC to supply that lonely socket where we need the power. Our solar inverter has a clever power detecter that switches a relay when production goes above 1Kw so I would connect this circuit to that relay. I also wanted to use a solar grid tie inverter from ebay because they seem most reasonably priced. They do however have a MPPT algorithm which is where I am not sure how it would react to a voltage source. Might anybody be able to tell me whether it would be fine to do this and most importantly about fixed voltage sources and solar grid tie inverters (which aren't really meant for fixed v sources). Many thanks, James 

Asked by fotherby 6 years ago


UPS battery backup as car inverter?

I hope this isn't a dumb question, but if I were to take an old UPS unit, remove the battery, wire a 12V lighter socket plug to the battery cables in the UPS, and plug it in to the car, would it convert the 12V DC to 120V AC while the car is running? And if it worked would it draw too much power or damage anything? I wouldn't use this to run anything with a motor, just a laptop charger and maybe a light. Thanks! :)

Posted by 500FPS 9 months ago


Any one can tell me is this circute working or not?? Please Urgent Expert advice equired? Answered

I want to make this 1.5 to 10volt inverter, I tried but it didn't worked. So I want advice from expert in this that is that circute working or not? If not what changes should make it work? Here is the link to schematic http://dangerousprototypes.com/2011/03/04/1-5-to-10-volt-inverter/ Thank you in advance.

Asked by njrajgelani 5 years ago


To make a 12 volt and 1.5A dc supply which supply power for 1.5-2 hours

I want to make 12volt 1.5A dc inverter which will supply power for 1.5-2 hours for my router. Please tell me how to make it?

Posted by mahedi_aiub 6 years ago


Current limiting high voltage - ccfl inverter help ? Answered

Okay as my first question i'll say hi first , and Darren from Ireland here , fair "know how" of electronics and how things roughly work. I have a 32inch TV who's inverter board is toast (okay its going on and off straight away) , I know its getting power from the psu board as there is little or no voltage drop when I flip the TV on and the lights fire up. I have asked 3 people at work (Electro techs at work) and they all say the same thing , replace the board , its too much work (I think there just lazy) and also they all say they would need the data sheet on all components or the circuit diagram. So well me with my stupid head wants to try and have a stab and getting a free TV. So I have ordered a CCFL inverter power source for a neon case light , which I intend to use just to see if any one bulb is gone as im not sure if that is what could be kickin the inverter off. And the other thing i have ordered is a "Universal inverter for 10-30v 4 bulb 17-24inch" from ebay. So the question is , if one bulb is gone and well i doubt i can order a bulb like this and replace as that would be end of tv if i open than panel . is there a way to simulate that bulb working in any way to stop the inverter going off because of one bulb. And the other question is , if I want to use this universal inverter , what is causing it too be a 17-24 inch only ? From what I understand is if I am wrong correct me please , that the larger bulb would burn the driver chips/fet's drawing too much current. So would there be a easy / safe way to just limit the out put so they will run but a little dim (as the tv is intended to be used in a dark room any way) Any ideas welcome , and for what ever comes up , Thanks !

Asked by dwoods-1 5 years ago


Noob Q about inverter for an ornithopter

I was looking in the back of my Jameco catalog the other day and they listed a product called "Muscle wire". It's apparently a nickel-titanium alloy that shrinks as it heats up. It occurred to me that I could flap ornithopter wings with it (a really small ornithopter). I was trying to figure out how I could switch voltage from one pair of wires (the flap UP wires) to the other pair of wires (the flap DOWN wires) without a microchip. I came up with something I'm sure wouldn't work involving a couple transistors, a diode and a cap. Today on wikipedia I figured out that what I was doing was something close to an inverter.So here's the question: Anyone know of a simple switching circuit that runs on a/c power and does not have square-wave switching characteristics?I'll keep researching this myself, but sometimes 'tis quicker to ask the big-brained and kind hearted (you know who you are).

Posted by royalestel 10 years ago


How many MOSFET's do I need? Answered

I am building a 2000W inverter powered by a car battery at 200A and I am unsure what to look at to find how many MOSFET's I need. Do I look at continuous current (in Amps) or power dissipation(in watts)? If it's power dissipation might you be able to suggest a MOSFET with a high power dissipation that is under a continuous current rating of 75A?

Asked by The MadScientist 7 years ago


How does a capacitor charger circuit work in a disposable camera ? Can I build it from scratch ? Answered

I wanted to ask this question for a long time... In every coil gun instructable there seems to be a readily prepared circuit that changes DC into AC, steps up the voltage and then changes it back into DC to charge a bank of capacitors. My guess is that the circuit contains an inverter, transformer and rectifier... Am I right? My question is, can I build that circuit from scratch ? If yes what materials do I need ? Thank you.

Asked by Eunix 5 years ago



A question about power inverter chips?

I need an inverter to use the 12DC of a battery to get an AC varying from 1 to 12V, and also the frequency has to be varying from 10 to 80KHz. the inverter will need to deliver 2W max.  I want to know if inverters do even exist in of IC chips, or will it be a board that i can buy, or am i obliged to make it myself? does a 2W inverter even exist or do people use oscillators for these kind of powers? 

Asked by ZakariaF 3 years ago


Do UPS inverters use Modified or Full sine wave?

I've been running my laptop, Desktop computer monitor, and a whole bunch of other things off a cheap 100w modified sine wave inverter for few years now, but have just recently started wondering if I got an old UPS that ran off of 12V for the inverter if it would be cheaper than buying a real full sine wave inverter. But I'm not sure if the inverter is Full sine wave for use with computers.  I have a small off grid system I'm using. Anyone know for sure?      

Asked by Bluevitz-RS 6 years ago


inverter circuit

I have several BD139 transistors, several types of transformers, blocker diodes and 40pf 50v capacitors. can anyone show me a simple schematic to convert low voltage to high voltage?

Posted by buddybro 4 years ago


hello anyone here know how to build a true sine wave inverter?

I just wanted to build my own power inverter to get a better understanding of how they work.

Asked by first1 9 years ago


how can you make a inverter that input 5v dc and output is 12v dc? Answered

I'm making a usb fan but it need more voltage to the fan 12v im only getting about half from the usb.

Asked by s4sutler100 8 years ago


Square wave inverter?

I am building an inverter that will use a square wave pulse to drive MOSFET's at 50-60Hz. I have read and heard a lot of stuff that running square wave into a transformer is not a good idea, what I want to know how bad is it? Also will adding capacitors as seen in my image be able to smooth the square wave a bit to help the problem? If so what capacitance should I use? (About 200A input) (The 12V square wave is coming from paralleled MOSFET's)

Asked by The MadScientist 7 years ago


Can anyone guide me through making an Inverter to control the speed of a 1HP single (or 3) phase induction motor?

I sometimes come across induction motors at a local tip that work but are of fixed speed, and wish I could use them better.  I have one at the moment which I plan to build into a humidity  dependent (with user override for occasional purge venting) ventilation system.  So I want to be able to control the speed of an induction motor which currently runs at a fixed speed, off single phase 240volts.  I wonder if anyone has experience they might share in putting together an inverter capable of doing this? Many thanks Bongo. 

Asked by bongodrummer 8 years ago


Switch electric polarity back and forth at least several times per minute?

I've seen a polarity inverter switch, but is there an automated version of one available that would switch the polarity continuously back and forth without needing to do it manually? Thanks

Asked by nlogic 8 months ago



LCD loosing backlight.

My backlights fail only when I input a viveo source of any kind. If I power up in RGB with a composite video source pluged in its fine until I switch the source to composite(video1). this is true for any source. they include S-video, RGB, composite, VGA and tuner. its run on 12V, pretty much Identical to a computer monitor except more inputs. thinking maybe the inverter, any other ideas will be helpful???

Posted by mool 10 years ago


Variable DC input to a clean AC out put

So here is what I am trying to accomplish. I am trying to take an old Jacobs wind turbine controller that was designed for a grid tie application and make it off grid. There is a 3 phase "wild" ac input from the turbine that is rectifyed but not clipped by the internal SCR's to variable DC (40-180 volts). The sensing was designed to tie to the grid and power sync'd to line power and freq then exported or imported depending on demand. What I would like to do is build a Variable Dc input inverter that will put out a pure sine wave 120/240 vac split phase. Thus imprinting a usable power out put and allowing the cap/choke inverter to do its part. The design need not handle much power as it is only used as an imprint to regulate the power through the controller. If anyone had any idea on a build for this or a manufacturer that is producing such an item I could really use some ideas. Thanks

Posted by nbrooks 7 years ago