​HELP! Looking for mechanical engineering advice in building a multiplier/compounding gearbox for a hand crank siren project

HELP! I have a project I'm working on that involves making a hand cranked mini air-raid siren utilizing a 12v generator and a 12v siren. I've done a proof of concept rig where I direct wired the siren to the generator and then used a drill to generate enough RPM on the shaft to get the noise I want. Problem is, I'd like to make this entirely manual and will be adding a crank handle once I get the housing built...which means, I need a way to seriously up my RPM. I've done research into building multiplier gear boxes and compound gear trains and pinions and everything in between, but am going to confess that while I'm obsessed with DIY projects, this one is exceeding my engineering knowledge. I am at a loss for how best to approach this build. What ratio would you suggest? 40:1? 50:1? Does anyone have experience building gear boxes that would be ok emailing me with their advice? The input for my generator is a 20 tooth gear (please don't laugh if I'm totally messing up all the nomenclature...most of my life experience comes from writing and baking and a very short (failed) stint as an EE...this is a totally new world for me.) and I got this information from another sub: it’s a 3600 rpm motor so 60/sec. I think the fastest I would want to crank is 2/sec, so, 30:1 gear box sounds about right. With a nice long crank handle a 50:1 should also work nicely. 10:1 is too slow. Ideally (and this might be where it gets really tricky) I'd like it to all fit into a space that's about 5"X3"X3, not including the siren (I can run that further out, using the leads).I'm attaching a photo of the original proof of concept wire up that I did...and don't worry, I know there are exposed wires, I fully plan on isolating the wires, insulating the whole thing and installing the proper resistors. https://imgur.com/a/MaAR2PQ Here is a link to the generator: https://ebay.us/zgAoDQHere is a link to the siren: https://ebay.us/fEgahDThank you in advance!

Question by Tye Rannosaurus   |  last reply


What is this tool for?

Can anyone tell me what this tool is for?   I came across it all rusted and thought it was some type of pliers or cutter. After I cleaned it up I could tell it was probably neither. What I thought was a plier jaw is actually one piece and does not close and what i thought maybe the cutting blade, actually had lines and numbers, like a ruler. The one small screw that the spring is attached to, will allow you to adjust how far the jaw/cutter will close and the other screw, when loosened a bit allows you to slide the little metal 'arm' in or out, like a measuring template. It has some fancy designs on the handles as you can see and the only marking says "Made in Western Germany".

Question by millsy22   |  last reply


Replacing motor in mobility scooter?

Hey all, I have a mobility scooter that I use for travel(caravaning among other). It's an Eloped Travel XL(40 kg or 88 lbs, 24V 22Ah battery), and I think it's only available in Sweden, but there are similar models all over the world.My scooter has got a 180w, 24v motor on a transaxle with integrated gearbox. The more I use it, the more frustrated I get. It's slow, 4mph/7 km/h, but worse, it really struggles uphill and sometimes it feels like its gonna stop all together. I've changed the batteries, with no improvement. It's not overheating. My guess is that it's just to weak. It might be ok to use when going to the shop or on flat surfaces, but not on gravel or grass.Anyway, I would like to replace the motor with a more powerful one, 350w or even 500w. The problem is that there isn't any compatible motors out there, so I'm guessing I'll have to replace the hole axle. I've been looking at these common China made electric motors that come in a range of sizes, have no idea about the quality though. Otherwise, maybe a powerful RC engine would work? I have no idea really, where to begin. Money is a concern unfortunately, otherwise I could buy a new transaxle or even a new, better scooter. Any ideas or help would be very appreciated! I'm quite handy but have never worked with these kind of parts before. How to pick the right sprockets, should I use chain or belt drive and so on.

Question by Alex Lillybear 


Can alternator create electricity IF yes can it generate 230 v and what size alternator would be required?

Can a alternator create electricity IF yes can it generate 230 v and what size alternator would be required? Would it be advisable to connect a transformer between a alternator and a battery?

Question by pvan heerden   |  last reply


Headphone started Peeling, any ideas? Answered

I have a SONY MDR-ZX600 Headphone which started peeling off at the ear pad and head rest area. I called the service and they wudnt replace it and i dunt want to buy new ones 'cause i wud face the same prob later. Is ther any idea to fix this and make it aestheticly pleasing?  Thanks!

Question by Kaushik LS   |  last reply


What is this tool?

I ran across this in a toolbox I inherited and have no idea what it does? Anybody have any familiarity with this thing?

Question by DrTurtle   |  last reply


220v 3 wire to 220v 2 wire (USA to Philippines)

Hello all,  I'd like to purchase a welding machine in the USA and take it to the Philippines. My problem and hopefully solution is, USA use 2 legs of 110v for 220v appliances/machines. In the Philippines, voltage is 220v (single leg). So, If I have a single phase, 220v welder, can I cut the plug off, combine the two power legs and connect to the power in the Philippines? I hope I am able to articulate this question properly. Mig welders are not easily available over there. Thank you for anyone that can help

Question by TerryH74   |  last reply


How can I tell if a first floor wall is load bearing? Answered

Hi, I would like to remove the wall between my kitchen and dining room to open up the area.  How can I tell if the wall is load bearing? The wall is on the 1st floor, runs lengthwise to the house and is about in the middle of the house, but it doesn't travel the entire length of the house. Any help or advice is appreciated.

Question by JMH renovations   |  last reply


How can I use my cordless drill on this old drill stand?

I got this at a garage sale but my Ryobi cordless drill does not fit properly into the holder/slot, it takes an old sears craftsman drill. Any ideas on how I can get it to work? Thanks.

Question by hmunster123   |  last reply


Advice sought on how to make Plastic mould

I’m trying to repair a folding camping bed. See picsIt has a number of feet and other blocks made of some form of HDPE or similar. I want to recreate these blocks. How can I do so? The material needs to be rigid but not brittle.I can find plaster or gel to make a mould but what material should I use? Is there some sort of binary mixture such as a flexible filler ?I have access to basic tools and power tools but not a lathe nor 3D printingAnother option is to buy a block of HDPE and drill and carve the holes, but where to buy the block (in UK)?

Question by big-bill3   |  last reply


Vacuum pump

Hi fellow iblershas anyone ever made a vacuum pump for a vacuum chamber out of an aquarium air pump before? Does it pull a good enough vacuum if you modify it? please respond someone. Thanks

Question by Disasterific   |  last reply


What to do with old window counter weights?

My house was built in 1915 and we are replacing the windows to get better efficiency. Now I have all these weights. I can have them thrown into a landfill but that seems like a bad idea. I've seen people doing things with homemade forges but I don't have one. Would these be useful? Could they be melted down? Or could they be toxic?

Question by Bitter73   |  last reply


wen scroll saw adapt kit Answered

Need to change my wen scroll to all painless blades. What do I need and were do I get it ? Help, New to this

Question by Craigpick   |  last reply


powerwasher won't throw out water from gun with motor running

Honda GC190 motor 3000pst powerwasher with a annovi reverbi pump RMV 2.5 G30  when all hoses are connected and the water is on, motor off, water passes thru nozzle, when the motor is on, the water does not pass out at all? How should I trouble shoot??

Question by natmac   |  last reply


Pop rivet stem removal? Answered

I need to use the pop riveter today, but there is a leftover 'stem' thingy stuck in it. I've removed the nozzle (?) and squeezed the handle a few times. but it's still stuck. I've tried pulling on it with pliers with no success.  

Question by mole1   |  last reply


Connect several DIY Bluetooth speakers

Hi peeps, I'm looking for Bluetooth (BT) amplifiers that can sync with a connected music device, for example an phone, so the music played from the phone will be sendt to all speakers. Hope my question are understood, and would greatly appreciate your feedback :)

Question by KayOeS   |  last reply


Is there a web site for mini mill engraver users?

Is there a web community out there that will have answers to some of the obvious questions that are going to arise when someone gets one of these machines? It has been a real dog fight to find any info on fine tuning these machines. Some of them are confusing to say the least. I am not talking about G or M code, I am talking about machine specs. Setting micro steps for better resolution. Fixing known problems with various machines, that kind of thing. There sure needs to be one somewhere.

Question by dannybush04 


What's another name for a rotary pneumatic indexing valve?

I am trying to find or create an air indexing or selection valve that has one line going in and several (6 to 12) coming out. I can imagine how to create such a thing: A valve disk that rotates in a body with 6 to 12 outlet fittings on the valve housing. The disk has one hole cut radially and one cut axially intersecting it at the center. Install in the valve body, spin it around with the valve stem, and there you go. Agitate away!The thing is, I'll bet these already exist if I could find them. Can anyone tell me what this thing-a-ma-bob is called? Or who might make them?

Question by cmblocker95   |  last reply


What would be the easiest way to hand-make an enclosure for a neon sign with a complex shape?

I want to make a rather small (less than 1 ft/sq) neon sign with a screen-printed plexiglass front, in the style used on the outside of stores (see attached image). Initially I'd considered just making a simple wood box, but for what I'm going for I need to make some more complex shapes, such as starbursts or clouds. Would I just get a strip of aluminum and bend it into shape, then seal the ends together, then just glue in the laser-cut piece of plexiglass? Thanks!!

Question by tim_finnegan   |  last reply


Q: cheapest way to remove bottom of water-heater

Hi, i pulled an electric water-heater (about 80 l) out of the trash. want to take the bottom off and convert it in a pot/kettle to do (´cook´ ) laundry over a wood-fire.i was wondering what would be the cheapest way to do it (i have very few means here)... rotary-tool?, hacksaw-blade?... (dont have a grinder, no blow-torch, no jig)guess to complete the cut i would use up quite a few of wheels, or, respectively blades (hack).any ideas? any feedback... all appreciated.bowing.

Question by la xerra   |  last reply


How to do a screen like this?

Hi,Does everyone know how to reproduce a screen like this?It would be to implement in front of a led matrix.Thanks.

Question by dreamstoxics   |  last reply


Vibration feeder anyone?

I am planning on building some sorting rig.Right now I am quite keen to include a vibration feeder system.You know, like the stff used to transport grain, sweets or aling small parts that run up on the inside of a bowl to come out perfectly aligned.I serviced these systems in the past but never put too much concern into the actual workings.The theory is quite simple.One or two vibrators cause the transported media to move.This works like a sawtooth wave.Slowly up and into the right direction, quickly back to where it started.Adjusting the frequency to change the speed or adjusting the amplitudes to match the weights and other properties of the media is easy - in a properly designed system.I tried to find some easy to understand information on the relations between actuator direction and media direction in relation to the trasport systems shape and dimensions but only got extreme complex stuff.In my small scale tests using simple vibration speakers and a frequency generator I had to relise that it is quite hard to find a proper way of mounting the system.To soft and it is just rattling around, too hard and you need to crank the amp to max to get any action.Orientation and angle of these mounts also affect the direction and amplitude of the swing caused by the vibrations.Straight linear I can do, although still not perfect but anything like these feeder bowls only gives me nice vibrations but no movement.Are there any suitable hobby projects on the web or here?And decent info on the basic design criteria for those feeder systems that are not closely guarded company secrets?

Question by Downunder35m   |  last reply


Turn an ATX Power Supply in to a Welder? Answered

I was wondering if I can turn an ATX power supply in to a welder: Before I write down the specs/amps of the power supply, I want to say that I have no experience in welding, I'm wondering if it's posssible to make a small welder out of an ATX power supply. Is there some kind of minimum current that you have to pass to start welding (softer?) metals? The lower the voltage the better right? I didn't give a lot of information, Because I don't know what to ask... Thanks :)

Question by Yonatan24   |  last reply


Heat transfer through cement

I have a garage on top of garage because my land is on a hill. The lower garage is all concrete all the way around including the ceiling. The floor in the upper garage is the cement from the roof of the lower garage. I want to heat the upper garage, but I know the floor will always be really cold because it is cement and the lower garage is not heated. The lower garage does stay quite a bit warmer than outside temps.My question is this, If I heat the lower shop, will the floor in the upper garage and the upper garage that is insulated be warm as well? Or am I better off just heating the upper shop and having a cold floor? I spend a lot of time in the garage and would like it comfortable when I am in there. ThanksJed

Question by jedidieah   |  last reply


Using an inkjet print head on a CnC device.

Ive had a bright idea that in short requires me to mount an inkject on a 3d printer of sorts for printing on a complex shape. Ive only done some cursory searching, but not found a "here is how to drive the inkjet" or "We recommend this model" for my purposes. Im toying with the idea of just ripping up a standard printer and seeing how well I can reconfigure that to my purposes, but I don't think it will do quite what I am looking for (in addition to the X and Y axis, there will need to be a Z, and in the eventual build probably a sensing mechanism to detect the shape it is printing on (im imagining a projected grid, but that is a ways down the line)). I'm going to have to learn a good bit of methodology to write the needed code, which is going to be a blast. But the starting point will be just the x & y coordinates and a DIY mounting of the print head.Any advice out there?I may build it out eventually on a raspberry pi but I haven't gotten that far as getting the mechanics working by feeding input to an Arduino for an almost etch a sketch mode will be my starting point.

Question by anguscormack 


How To Connect A Stepper Motor to Turn a Solar Panel

I want to use a stepper motor to turn a pipe or 2x2 piece of wood connected to a solar panel. I want this to be a direct drive system. No gears, no belts. I can't find an example showing how I can connect a stepper motor stem/bolt to a mount that it turns, though. I can see them connected in projects, they mysteriously leave out the details on the parts used and the details connecting it or they use gears/belts.

Question by blairr5   |  last reply


How to order the correct ball bearings and threaded rod so that they will seat well and not be loose or have play?

I am trying to design, what will essentially be a very specific miter box / saw guide for a hand saw. Here is a product on the market that is almost exactly what I am trying to build. The only difference between what I need to build and this miter box, is that the miter box from that link cuts at a 90-degree angle to the workpiece being sawn, whereas I need to saw boards at angles much more acute than 90-degrees. There are commercially available adjustable miter-boxes, such as this one, that allow you to set whatever angle you need, and it will still guide the saw straight. However, they are made for cutting baseboards and molding, so the angle-range is only 90-degrees to ~40-degrees or so. I am cutting wooden boards for making, "scarf joints". So, I need to saw through 4" thick boards at an 11-17 degree angle. Where the above miter box saws perpendicular to the board it is sawing, the one that I am building, at 11-17 degrees, will be closer to cutting parallel. The housing, I think I can cobble together from angle aluminum and hardwood. However, I haven't bought ball bearings since I was a kid riding skateboards. I was hoping to take a threaded rod and push it through the hole in some bearings, then use some spacers and/or washers to space them apart, and secure the whole bearings/spacer/bearings sandwich with some washers and nuts. I do not live near a place that actually sells bearings much less carries bearing and threaded rod in the same store. Therefore, I cannot try it all out right there in the store. So I am going to have to order the bearings and the threaded rod off the internet. I need bearing where... Heavy load is not an issueHow fast they spin is also a non-issue.But that are...Shielded from the sawdust (do not have to watertight)Fit snuggly on a threaded rod and not rattle around. A loose guide-bearing isn't much of a guide, eh?Would one of you fine gentlemen help me by pointing to where I can buy 16-20 bearings, a threaded rod that will definitely fit them, and some .50 - .75" spacers (metal or nylon) that will also fit the bearings?

Question by Dolmetscher007   |  last reply


Dog bowl stand.

When my dog drinks water it splashes on the floor. I thought if I raise the bowl up on a stand it won't splash so much. I needed help building a stand. A DIY..

Question by NStarwoman   |  last reply


How Would You Fix This?

I've watched videos on YouTube about it and have never done body work before. So I'm trying to soak up as much info as I can from as many sources as possible. It's hard to find forums that are updated frequently so that's I'm posting on here. Can anyone suggest how they would go about fixing this type of rust? The more detail the better, thank you.

Question by MustLearnStuff   |  last reply


what is this? identify my tool!? Answered

I had this for years, anybody got a clue what it is? most amusing answer gets a patch:-)

Question by crazyg   |  last reply


Identify a Signet Ring? Answered

My grandmother gave me a signet ring a week ago, and I was wondering if anyone could help me identify the coat of arms on the front of the ring. I don't know what metal it is made from, and there is no visible hallmark that I can see...

Question by ObsidianBlush   |  last reply


PDF's are 0 (zero) bytes

I am a 'new' Pro Subscriber. I tried downloading .PDF from this posting using Firefox (and Chrome);https://www.instructables.com/id/How-to-program-arcs-and-linear-movement-in-G-Code-/The files are zero bytes. What's up with that. What's the solution?

Question by squattingdog 


How do I fix a Black & Decker electric lawn mower motor?

A neighbor asked me to have a look at her B&D electric mulching mower (MM1800 Type 1) after it stopped working. When I pulled the control switch, the blade didn't turn, but there was a buzzing sound and kind of a burned plastic smell. I also found that it was very hard to turn the blade by hand. At home, after a lot of trouble I was able to remove the 6 screws holding down the big plastic cover. (You should see how much grass was under there.) I can now see the outside of the motor, but how do I figure out which parts need to be replaced? The owner's manual has a parts list. I assume that some parts (like the magnet ring and armature) are OK, and that the problem is with something like the brush spring/terminal/brush insert or rectifier. How do I find out? (I'm hoping it won't be that hard to replace the parts of the motor.) Thx.

Question by bkbkbkbk   |  last reply


Slicing a hockey puck into discs (vulcanized rubber)

I need to slice a hockey puck (1” thick by 3” diameter) into very thin discs (1/16” to 1/32” thick). This can be done... the NHL sells 1/4” puck coasters (see photo). Thinking about a mandolin design where the puck is mounted and the blade moves with my hand in a sled device. Puck rubber is very hard to slice. Thinking of Japanese angled blades (‘7’ shape rather than the American ‘V’ shape). Looked into ice auger blades (for blade thickness and stability). Just about de-gloved my hand with large box-cutter blades (bent as well when cutting the rubber). Any ideas? Raincock@ualberta.ca

Question by Marfeetus   |  last reply


12V DC Motor Wind Turbine

Hi im trying to build a wind turbine.The purpose of the wind turbine is to determine the maximum amount of power it can produce with different loads. It needs to produce at least two watts of power during testing, I tried using a potentiometer but it started smoking. I need to record voltage, current and power. I needed to know how to set this up, and if I can use resistors instead of a potentiometer. I have power supplydmmresistorsblade12V DCWires

Question by hj212121   |  last reply


Does anyone know how to identify a ring? Answered

I have a ring but i dont know what kind so could anyone please tell me if they know a way to identify it, Thanks.

Question by tastur26   |  last reply


is there any way to harden floral foam? Answered

I am making some molds and stuff from floral foam, and I wan't to know if there is a way to harden it and make it heavy.  Some of the things I'm making will have to take handling and painting without chipping, breaking, or crushing.  I use floral foam because it's easy to use, so I can make models in the first place.  I'm not looking for another medium, but how to change it once the model is made.  Also, I cannot use anything expensive or that must be bought online.  Preferrably something like paper-mache, but that will not stick out from small crevices in the model. 

Question by jduffy54   |  last reply


Tinkercad Judges' Prizes

So I was just wondering, how are the Tinkercad Prize winners selected? Are they chosen before, after, or at the same time as the other finalists? Are they chosen the same way? Let's say I entered a project that uses Tinkercad and I end up being selected as a finalist and end as a finalist, recieving an Instructables Prize Pack as a reward. But technically speaking, as long as I qualified, if I had been selected for the Tinkercad Judges' Prize instead, I could've gotten something much better. Or let's say I made an outstanding Tinkercad project and could potentially win the Grand Prize, but instead get chosen for the Judges' prize because I was one of the best Tinkercad entries. Still awesome, but not nearly as awesome as the Grand Prize.If a project excels in both the contest's category and does a great job using Tinkercad, what decides where they end up being put?Is it possible that using Tinkercad could actually limit your chances at the Grand Prize?How's this work? Anyone have any idea? Thanks in advance,A befuddled idiot =P

Question by m_shannon 


table saw fence help?

Hello my fellow indestructible friends i brought a table saw this the first table saw i got and the fence is not completely strait it goes outwards by a couple of mm or more is this right many thanks for ant response here is the table saw http://www.screwfix.com/p/titan-ttb674tas-254mm-table-saw-230-240v/9486j  please tell me if its okay or if not how to fix thanks paul

Question by paul the maker   |  last reply


Electric Hub Motor

I have 48V 6AH Battery and 350W Hub Motor with controller for Fat tyre CycleIm getting a speed of 40.Hence want to know to increase speed upto 55 or 60

Question by DattatrayaM   |  last reply



Residential wiring problem. Power in both positive and negative outlet. Answered

Helping Pops out on this one... He's got a spare room with a small adjoining bathroom. The wiring breakdown on the fusebox indicates that these two rooms are wired as part of the same circuit on the main breaker. In the two rooms there are: 2 outlets, 1 GFI outlet, and 4 switches controlling 2 lights and 1 bathroom ceiling fan. In the last few months this room has been experiences some abnormalities in power: flickering lights, occasional outage, GFI tripped. The outages usually lasted less than an hour and would occur with or without any load and any time. GFI trips sometimes, but other lights will work on the circuit when it's just the GFI. Recently all power to this room has stopped. The main breaker never trips. With everything unplugged (including the ceiling fan) I checked the outlets in the room. Screwdriver voltage tester was used. The probe registers a 'charge' in the outlet and 'no power' on the return. Normal. However when any load (light, clock, tv) is applied all outlets instantly register a charge in both the positive and the return. Not normal. The breaker doesn't trip, resetting breaker or GFI doesn't work, and the positive and negative terminals of the outlets are both registering as charged. House is 10 years old with no previous wiring issues, in Canada. Can anyone tell me what's wrong? edit: January 24, 2011 Problem has been located and fixed. Closer inspection of the breaker panel revealed that the neutral was loose, and had started to melt the casing of the wire. The wire was clipped and spliced, and now things are back to normal. Thanks for everyone's input, best answer awarded!

Question by mikeasaurus   |  last reply


CNC Electronics - Grounding and probe

Hello!Reading about proper grounding of cnc electronics I saw that ground has to be isolated from power supplies negative. So, I have a copper plate with ground cables from 48v, 12v and 5v power supplies with ground cable from the wall. Everything works fine but the machine itself, has no ground cable because if I attach the negative of my probe cable I will be connecting negative to ground... This morning touching the machine structure and the door handle (the door is metalic) I felt a light discharge. Should I connect the maching to ground? Can this affect in any way the electronics with that negative to ground? ( the discharge was lightly, I can live with that lol)The router has no ground cable, maybe that was the reason for the discharge.Thanks!!

Question by ryghar   |  last reply


Question: does anyone know if there is an aluminum pipe expander over 6" in diameter

I would like to find a portable aluminum pipe expander a half inch over 6" for repairing aluminum irrigation pipe or any other ideas about how to repair them. thanks ron fancher

Question by flagman12   |  last reply


Dead Dremel help

I have a Dremel tool that is a few years old.  the other day it quit working, I was using it heavily.  I checked the brushes they looked fine.  I opened it up and everything looks OK the motor/ shaft are connected and spin. The  only thing I noticed was what looked like a thing strand of solider on the one side near the brush.  Any ideas?

Question by denkeeper   |  last reply


How does one with no experience learn to work on and fix up cars? Where to start?

I am a girl and I have been interested in fixing cars for a while. Quite a few guys at my school seem to know how to fix cars up, but they had to start somewhere, right? Often, I think peoples' fathers help them out, but my own father knows nothing about cars, nor shows any interest in helping me. If anyone has tips on where I could start, perhaps I could find a shop where people would help me? Or do any car co-ops exist? I know there is such a place for bicycles where I live. Any tips would be great! I am enthusiastic and have some background with fixing bicycles and doing wood and metal projects, so I'm not mechanically clueless. I am mostly interested in old cars, but anything to start would be alright. I have browsed Craigslist for cars and found a few I could afford. On that note, I have a teen's level of funding, so I could find something, but tips on making the best of my money when going about fixing up an old car would also be appreciated (especially considering the cost for parts and such). Any tips on where and how to start are what I am looking fore. Thank you!

Question by toolgal29   |  last reply


Use of diodes when connecting solar panels in parallel?

I have a bunch of 24 volt 270 watt solar panels.  Eventually I'll be putting three in series, then combining the strings in parallel, but for a temporary measure, I want to just connect two in parallel.  I've been in tv repair for over 40 years so electrical theory doesn't confuse me, but solar systems are a different story.  I've used four smaller panels to run a car radio display at an old car show swap meet for the last 12 years, and I just ran them in parallel, then into the charge controller.  Now I'm reading about blocking diodes, and I understand what they're for and that some people use 'em and some don't. My question is, physically, where do you stick them, and related to this, what is the purpose of using a combiner box?  Is the box just to provide a weatherproof place to make the connections?  Are they used to provide the place to stick the diodes?  I see they have circuit breakers inside, and it appears there's one for each panel, or string of panels, but I don't see the point.  If a panel can generate 10 amps, you'd want a breaker bigger than that so it doesn't trip at full output, but what could trip it then?  You can't get more than 10 amps even if there is a short. This should be common sense, but since I don't have a combiner box yet to look at, can I assume if it's made to combine four panels or strings of panels, you can connect just two or three and save the unused ones for adding on later? Thanks bunches; caradiodoc

Question by caradiodoc   |  last reply


Projects to use a bilge pump?

I have a 500 gph fully submersible rule bilge pump that is not needed for anything. I've been looking around and trying to find a use for it. I feel like the possibilities are endless yet I can't think of anything. It's a 12 volt 2.5 amp pump. Any ideas?

Question by Kirschbj   |  last reply


I accidentally poked small hole in freezer cooling line, can I patch it with flex seal or something like it?

Was de-icing my haier mini fridge, when I accidentally punctured a tiny hole in  freezer wall cooling line, it hissed for like 2 seconds. Is it safe to plug back in? and can I patch the hole?

Question by brandon.salinas.319   |  last reply


FoodSaver Vac 500 pump parts?

I took apart my slowly sucking Vac 500 and discovered the plastic ring around the piston on the pump is broken and I'd like to replace the part.  Any leads?

Question by accelv   |  last reply