With Instructables you can share what you make with the world, and tap into an ever-growing community of creative experts.
Air Flow Sensor From Scrap
100 LED 10 band Audio Spectrum atmega32 MSGEQ7 with peak hold and fall down
8x8 LED Matrix Display
plz kindly tell me the circuit diagram for AC pwm dimmer
Please specify all components which is used to design...??
PWM dimmer using NE555 and MOSFET with DIY aluminium case.
simple mobile detector circuit
low cost 1 wire lcd for 8 pin micro controllers [romanblack shift1 system ]
CPU Fan controller using PIC
Simple Electromagnetic Engine using piston and flywheel
Is it going to detect on basic cell activation or smartphones aswell.#admin
the project is quite interesting, could you kindly share the "mikro c" code plz my e- mail : email@example.com sir, thank u
Wireless Robo-car using 360° servo motor
Hola, me pueden ayudar, no me funciona el circuito, no se si sera porque estoy utilizando un IRF740 en ves del IRF830, el voltaje de entrada AC es el mismo al de salida AC ayuda
Is copper wire used as anntena....??? - DivyeshM1
Thanks you - rahulnaik388
low cost air flow sensor
Hello there.. Can anyone help me to make this circuit respond to high frequency? I got it working okay till 3kHz. I need it to work with a 32kHz frequency. Which component should be swapped for making work at such a frequency?
It depends on the current carrying capacity of the bridge and the mosfet. For example, if you need to control a 1000W load, the Mosfet and diodes in the bridge should carry atleast 5 Amps (1000W divided by 230V) of current. You can upgrade the circuit with higher current diodes and MOSFETs to achieve this.
safe and simple AC PWM Dimmer for arduino / Raspberry pi
my 40wled@12v portable handy floodlight.no kit required
Reliable and low cost IR Proximity sensor
Raspberry Pi real time ECG plotting
Please email me the project details ... firstname.lastname@example.org
Pleass email me the project details..... email@example.comThanks
Digital ic tester using pic microcontroller
I have 44v system and 10000mah or 10a so should i get a step down? I'm also trying to hook up blue 12v led lights, so i don't want to stress the battery with 4 different circuits running through it. 1:system/2:charge the lithium-ION/3:100w chip step down/4:12v led step down
hi i'm a college student and i'm planning on using this for my project can you please send me the source code for this thanks here is my email add firstname.lastname@example.org
hi i'm a college student and i'm planning on using this for my project can you please send me the source code for this thanks here is my email add email@example.com
I used it as part of my Capstone project in Engineering.
PIC12F675 development board micro size 3.0 cm x2.5 cm
Please share the source code to everyone for learning purpose.Without the source code,the project is kind of incomplete to the end user.Obviously anyone who is working on microcontrollers,doesn't want to do a copy-paste type job!!!!Making the project without knowing the source code would be like that copy-paste type of work....
pls mail me the project details.....firstname.lastname@example.orgThanks
Just used this as part of my capstone project. It worked great!
I am looking to build this for an undercabinet lighting system. I would like to ad a mode could you please send me the C code.
Hey, I'd ask about the switched in this circuit. can i put "switched"? thanks
Hey I'd ask about the full power capacity of this circuit ?How many Watts ?
hi,I really tried multiple times but I am not getting success and being disappointed every time. I want to build this circuit can anyone send this pre-build circuit so that I can understand this where I am going wrong. I can pay for it :(
Please help I have made a cell phone detector but the buzzer or led just keeps glowing
Hi sir can u plz give me ur contact number; i need some help
Hi, Will this detect phone signal basestations and towers (in the absence of a phone) too?
Can we operate it at 9 v
(1 band use only 1 led)
how to design the MSGEQ7 separates the audio spectrum into 5 or 7 frequency bands?please help me!
Join 2 million + to receive instant DIY inspiration in your inbox.
Download our apps!
© 2016 Autodesk, Inc.