With Instructables you can share what you make with the world, and tap into an ever-growing community of creative experts.
Tell us about yourself!
You don't need a device to Lucid Dream. It does however take effort on your part.I have been Lucid Dreaming for nearly 20 years.There is a lot of good info on the internet.It is very important to keep a dream journal.Good Luck.
Try vaseline and the casting should come out easier.
Nice Ring an instructable.
Intro to Fusion 360: Lamp Design
Circuit Board Design Class
Nicely done. I've seen one of these on youtube that used square tubing. I want to make on for my rocketstove.
Great project. Especially since parts were made on a 3D printer.
Wow good for you Dad. These are things a kid will cherish for the rest of their lives.
I love it. Especially the sound. Just like a steam engine. I think I am going to print one. Thank you for sharing the stl files.
Nice build.All I am missing is the wood lathe ;-)
That is ingenious.
Welcome to Writing an Instructable
How to Write an Instructable
Beginning to MIG Weld
Thank you for the reply.Since I receive a response until yours, I gave it a try and noted it does get loaded into memory.Thank you for the reply :-)
This is good information and thank you for sharing it.I do have a question:When you enter these values for calibration, are they stored on the Repetier Software or written to the control board of the 3D printer?I ask because I use an SD card when I make my prints leaving my computer free for other activities.Thank you for your response in advance.
This good information and than you for sharing it. I do have a question: When you enter these values, do they get stored on the control board of the printer or held in the Repetier software? I ask this because I use a micro SD card to make my prints and hope the calibration is stored in the control board itself.Thank you in advance for you response.
Nice Instructable but Dude you need a Bigger Shop.I got clausterphobic just watching the video ;-)
Good Instructable but Dude you need a bigger shop ;-)
I made a pair.Springs I used I purchased at my local Hardware Store.Springs are 3.25" X 14/16" or 82.6mm X 20.6mmJust waiting for the magnets.Thanks for the Instructable.
Made one. Just waiting for the magnets. Springs were sourced from my local Hardware store. Thanks for the Instructable.
I like it! Simple and effective that should accommodate all sorts of PCBs. I need to make one. Thanks for posting it :-)
Raspberry Pi Class
Great Instructable. Keep them scratching their heads for hours.
Welcome to Arduino
You an't create free energy from magnets.
You can't create free energy from just magnets.
Not Free Energy. You need to apply the input by moving.
This is Horsh Sh*t This is not an instructable, this is a buffon attempting to fools those who do not know any better.
Welcome to CNC
Yes some of us know it has been available for other platforms including windows for years. There are many others are seeing this for the first time. Thew poster took the time to provide this information so give the poster a break and refrain from making comments that you feel are obvious. They only serve to ruin the spirit of sharing information.
3D Printing Class
I made PCBs using the same method nearly 20 years ago. Laser printers were quite expensive back then so I would take my graphics to my local printer and had them make photo copies using their laser paper. Ironed onto a clean PCB and used water to remove the paper from the melted toner. Worked great.
Yes they were. I think I may try it again and see if things have improved since then.
Thank you for the Information.
It looks good. I have a few Mac Minis but they don't seem to get hot to need a cooler.
I see you are using the Chromecast Audio. Can you only play music from streaming sites with it or can you play music from memory such as a harddrive? BTW: Nice job on the Speaker
This can be used as a Torch. This cannot be used to run a car by having the car produce the gas as it is driving. If you read that on the internet, it is false.
Stanely Meyer was a fraud. He never built a vehicle that ran solely on the electrolysis of Water being created from the vehicle while driving. Yes I seen the Patents, but a Patent is easy to get if it is proven unique. Meyer did not have to prove the Patent office that is ran a vehicle. All it showed was his electrolyser. It is impossible to run a vehicle on the electrolysis of water while at the same time producing the Gas from the Engine driving the Electrical system and Wheels.
True but if you open the case and disconnect the balancer, you can use a power supply to get the voltage up past the threshold and connect everything back together it will start charging again.I have done that several times with laptop batteries that would not charge because they were discharged below the threshold voltage.
Let your inbox help you discover our best projects, classes, and contests. Instructables will help you learn how to make anything!
© 2016 Autodesk, Inc.