The Sipriani Rifle
Intro: The Sipriani Rifle
Check my White Tiger V2 Rifle too!
"Mods" by The_Builder, go to this link.
"Mods" by Kookoo For Knex, go to this link.
This is it: My Sipriani Rifle
It's a high-powered rifle that shoots about 35 to 110 ft depending on the amount of rubberbands
Pros:
-True trigger
-Very powerful
-Comfortable handle
Cons:
-Could give some physic damage when hit (DON'T FIRE THIS AT ANYONE)
For short:
It's very recommendable rifle.
"Mods" by The_Builder, go to this link.
"Mods" by Kookoo For Knex, go to this link.
This is it: My Sipriani Rifle
It's a high-powered rifle that shoots about 35 to 110 ft depending on the amount of rubberbands
Pros:
-True trigger
-Very powerful
-Comfortable handle
Cons:
-Could give some physic damage when hit (DON'T FIRE THIS AT ANYONE)
For short:
It's very recommendable rifle.
STEP 1: Piece List
Piece list
70 green rods
47 white rods
4 red connectors
1 y connector
2 ball sockets
41 yellow connectors
4 grey 2slot connectors
2 white snowflakes
4 green connectors
12 blue rods
15 grey connectors
70 green rods
47 white rods
4 red connectors
1 y connector
2 ball sockets
41 yellow connectors
4 grey 2slot connectors
2 white snowflakes
4 green connectors
12 blue rods
15 grey connectors
STEP 2: The Chain
This part is not neccasery, but it just makes it look cool.
and this way, you can carry it.
and this way, you can carry it.
STEP 3: The Handle
This part is needed for comfort and for the safety of your fingers.
STEP 4: The Rear
This part is for stablitity and for protecting your eye when sniping.
STEP 5: Trigger
This part is for holding the rubberbands from flying everywhere!
STEP 6: The Barrel
This is the most important and, finger torturing part that is needed for holding the bullet.
STEP 7: Putting the Rifle Together
Pic 1:barrel + trigger
Pic 2:put them together
Pic 3:trigger + rear
Pic 4:put them together
Pic 5:chain + barrel
Pic 6:put them together
Pic 7:handle + trigger
Pic 8:put them together
Pic 2:put them together
Pic 3:trigger + rear
Pic 4:put them together
Pic 5:chain + barrel
Pic 6:put them together
Pic 7:handle + trigger
Pic 8:put them together
STEP 8: The Rubberband Holders
build these two.
STEP 9: The Rubberbands
pic A: put the rubberband as shown
pic B: put the rubberband as shown
pic C: put on the rubberband holders as shown
pic B: put the rubberband as shown
pic C: put on the rubberband holders as shown
STEP 10: Ammo
The bullets:
they come in grey, black, white and blue.
they come in grey, black, white and blue.
STEP 11: You're Done!!!
Well you've built yourself the Sipriani Rifle
Have freaking much fun with my gun!!!
Have freaking much fun with my gun!!!
298 Comments
evilkellan123 7 years ago
Guys, be very careful with this gun, I currently have a hole in my hand because it jammed and I unknowingly put my hand upon the barrel, then it fired once I fixed the jam, into my hand. Other than the jamming issues, it is an amazing gun.
koolcoasterkid 9 years ago
Lol, I remember building this when I was very young, there are still holes in the wall from it :P VERY powerful, great simple design.
mister knex 11 years ago
knexrule2012 12 years ago
VERY POWERFUL!!!!!!!!!!!!!!!!!!!!
knexrule2012 12 years ago
Snosageman99 12 years ago
Skreetsha 12 years ago
It's basically the same as a tan connector but without the small sticky-outy piece.
V
Snosageman99 12 years ago
Flatout Knex 12 years ago
Haloness 15 years ago
Flatout Knex 12 years ago
jedi_knight 14 years ago
mr.origami 14 years ago
tytiger33 13 years ago
Shredder543 13 years ago
An Villain 13 years ago
Skreetsha 14 years ago
Haven't had a good comment on this one in a while.
Good times.. good times..
jedi_knight 14 years ago
bombmaker2 14 years ago
hedzup456 13 years ago