GTP USB PIC PROGRAMMER (Open Source)
Intro: GTP USB PIC PROGRAMMER (Open Source)
This work includes, GTP USB (not plus or lite) .
The schematic, photos and PCB have been developed by PICMASTERS based on
some valuable works done before.
This programmer supports pic10F, 12F, 16C, 16F, 18F,24Cxx Eeprom.
Unfortunately, it works with only Winpic800 v.355.
We have succesfully tried it with some pics; PIC18F252, 18F2455, 18F2550,
18F2520, 16F84, 16F628 and 24C32 eeprom.
The best and fastest method of pic programming.
All you need (hex file, winpic800, schematic, PCB board in ARES)
are included.
You must program pic18F2550 with hex file by a classical programmer.
Just leave a good fedback for us.
The schematic, photos and PCB have been developed by PICMASTERS based on
some valuable works done before.
This programmer supports pic10F, 12F, 16C, 16F, 18F,24Cxx Eeprom.
Unfortunately, it works with only Winpic800 v.355.
We have succesfully tried it with some pics; PIC18F252, 18F2455, 18F2550,
18F2520, 16F84, 16F628 and 24C32 eeprom.
The best and fastest method of pic programming.
All you need (hex file, winpic800, schematic, PCB board in ARES)
are included.
You must program pic18F2550 with hex file by a classical programmer.
Just leave a good fedback for us.
STEP 1: Circuit Scheamatic
circuit schematic. You can see the type and value of the companents.
STEP 2: Circuit Layout
Circuit layout.
STEP 3: Top Layer
top layer lay out.
STEP 4: All of the Documantries
You can find usb driver, layout of the circuit , all of the pics of the circuit, and hardware setting program
STEP 5: Pics
COLLECTING THE DATA IS ONLY THE FIRST STEP OF THE WISDOM, BUT SAHRING DATA IS THE FIRST STEP OF COMMUNITY.
171 Comments
49percentGood 10 years ago
KarimM44 4 years ago
SERGIODS 10 years ago
y el que lo diseño es de cheyo28
http://www.forosdeelectronica.com/members/cheyo28/
MiguelJ1 9 years ago
para
programar un pic especifico todos los programadores que se utilice con ese pic tendrá
diseños parecidos por la sencilla razón de que ese pic se programa igual en
todos los programadores sus respectivas tensiones en sus pines deben coincidir
para la programación y por ende los circuitos serán similares esto se cumplirá
siempre que la programación sea por el mismo puerto igual en todos ellos
feedel 10 years ago
pls where is the hex file
morningshofi 10 years ago
uddin.shofi@yahoo.com
SERGIODS 10 years ago
y el que lo diseño es de cheyo28
http://www.forosdeelectronica.com/members/cheyo28/
daz7691 10 years ago
ssparking rajesh 11 years ago
dlimzakir 11 years ago
thanks... penticon2003@yahoo.com
Nitsuku12 11 years ago
Can i ask whats the purpose of 18f2550(replacement 18f4455) in this programmer? which is there is already a 40 pin ZIF socket for programming, i use 16f628. Confusing.. I building my new version of GTP programmer.. so i need some help..
Nitsuku12 11 years ago
Can i ask whats the purpose of 18f2550(replacement 18f4455) in this programmer? which is there is already a 40 pin ZIF socket for programming, i use 16f628. Confusing.. I building my new version of GTP programmer.. so i need some help..
kwest8 11 years ago
Cartola43 11 years ago
sekar6697 11 years ago
pleas i want to ask about the cable in the left side in the picture
what it's job and where it's connected
i'am waiting for your replay
and thank you again
bvv134 11 years ago
Z.K. 12 years ago
pahexa 12 years ago
gud luck ..
marcosviera 12 years ago
ahmedsobhi 12 years ago