USB LED Backlight

24,875

57

55

Introduction: USB LED Backlight

Really simple build for a USB accent light utilising a generic type "A" USB cable end (the wide one), a 100ohm 1/4 watt resistor, 1/4 inch shrink wrap, and a 3.5 volt LED (I used blue to be different).

Step 1: I Can't Believe It's So Easy...

Image is pretty self explanitory, just solder the LED as close to the USB connector as possible with the resistor on the anode (+) leg of the LED. Slip on the heat shrink tubing, heat until golden brown, and diffuse the tip of the LED with some sandpaper or a disposable nailfile. These work really well behind my desktop, laptop, xbox360, cable box, and dvr.

Be the First to Share

    Recommendations

    • Toys & Games Contest

      Toys & Games Contest
    • Big vs Small Challenge

      Big vs Small Challenge
    • Fix It Challenge

      Fix It Challenge

    55 Comments

    0
    Big jermini
    Big jermini

    13 years ago on Introduction

    Ok resisters are not that easily explained. resistors in series with anything drops Voltage. resistors in parallel with anything drops current. Think of your circuits like a water hose. voltage is how much water is flowing and current is how fast. put a resistor in series and it is like stepping on the hose voltage goes down current goes up. now try adding another piece of hose in parallel with the first hose. (a resistor in parallel). The voltage stays the same but the current goes down. So if you wanted to take down the current you would need to put the resitor in parallel with the LED. IF your limiting Voltage Put it in series. I am taking EET/CET and have just passed AC/DC(no pun intended) digital and hardware. Now after break its on to communications. yeah! Just trying to help by the way.

    0
    The Expert Noob
    The Expert Noob

    Reply 13 years ago on Introduction

    are you sure? cause I tested this with my multimeter with the resistor in series and still got 5v but like ~25 mA (LED was rated at 20mA but still within max range) When I put the resistor in parallel, my current kept going up, but my voltage was at 4.2 volts and my LED got hot and started to turn a reddish green, then popped. So in conclusion, i believe running a resistor in series limits current, hence its name, RESISTS CURRENT! Ohms Law states I=V/R, Voltage is constant (5v) the greater the denominator(resistor) the lower the current

    ex. I=5/100, I=.05 | I=5/120, I=.041667

    0
    The Expert Noob
    The Expert Noob

    Reply 13 years ago on Introduction

    In replying to myself, i just did another experiment, and I should know this from wiring speakers, a resistor in parallel, will actually draw more current for the LED but keep the same voltage causing my pop. Wire two 100 ohm resistors and you get 50ohms with double the current draw. and LED has resistance, putting it in parallel with a resistor is a bad idea unless you want to blow it.

    0
    gmh5760
    gmh5760

    Reply 9 years ago on Introduction

    The reason for the 4.2v is because of the forward voltage drop of any typical diode (light emitting or not), which is about .7v. This will always be a near constant. Resistances wired in parallel REDUCE overall resistance, thus current increases. To calculate resistors in series, simply add the values. If the resistors are in parallel, add the inverse values of all the resistors (1/x) together, and then take the inverse of THAT number as well. On a scientific calculator, typical entry for 4 50ohm resistors would like this: 1 / (1 /50+1/50+1/50+1/50) = 12.5ohms.

    0
    Steve Potman
    Steve Potman

    10 years ago on Introduction

    I would not use the electrical tape instead of the heat shrink tubing because I would want it to look nicer, but it would work. I just got heat exchangers and some heat shrink tubing a week or so ago, so it is available to me, but I would suggest buying some and using that.

    0
    shutupkitty17
    shutupkitty17

    11 years ago on Step 1

     Instead of heat shrink tubing, electrical tape would work, right?

    0
    punkhead58
    punkhead58

    Reply 11 years ago on Introduction

    Of course, shrink tubing just looks nicer.

    0
    milsorgen
    milsorgen

    Reply 11 years ago on Introduction

     Yes, in fact depending on the application many things could be used. Cardboard for instance.

    0
    bobtannica
    bobtannica

    11 years ago on Step 1

    Thanks for your 'ible. Even with my limited skills it was a snap!

    0
    sk83rjosh
    sk83rjosh

    12 years ago on Step 1

    what is the point of the resistor? i tied with out one and the led got hot i mean relly hot! is that normal?

    0
    samanen
    samanen

    Reply 11 years ago on Step 1

    You need to use resistor, if you don't want to take a risk that the LED'll go hot or explode. I exploded my best led by using not a resistor ;'(

    0
    sk83rjosh
    sk83rjosh

    Reply 12 years ago on Step 1

    lol nvr mind itll burn up i have on hooked up to a 10 watt for now itll last 10-20 mins if i leave it on how long would 100 one last thats a 10 p resitor correct i had one but it dimed my light way to much an mines an ultra bright green you think itll be safe if i leave it on for extended periods say 30 min-1 hour??

    0
    Yerboogieman
    Yerboogieman

    13 years ago on Introduction

    you know how you cant believe it so easy? i cant believe its not butter.

    0
    drderek
    drderek

    13 years ago on Introduction

    Does it matter if the resistor is 1/2 or 1/4?