Rainbow Candy Wrapper Wall Art
Intro: Rainbow Candy Wrapper Wall Art
Have you ever wanted to impress your friends and save the environment at the same time? If so, your in luck!
this is a quick and easy project to do and only requires patience.
this is a quick and easy project to do and only requires patience.
STEP 1: Gather the Supplies
this is what you will need:
-a ruler
-duct tape
-scissors
-around a 14X14 inch white poster board or any color you may choose
-20 to 30 Dum Dum's candy wrappers
-a ruler
-duct tape
-scissors
-around a 14X14 inch white poster board or any color you may choose
-20 to 30 Dum Dum's candy wrappers
STEP 2: Preparing the Wrappers
1. lay down the wrapper color side up and the bottom of wrapper facing towards you as shown
2. next fold the bottom right corner until it meets the top of the wrapper and forms a triangle shape
3. cut off the unfolded part on the wrapper, or the rectangle leaving a perfect triangle
2. next fold the bottom right corner until it meets the top of the wrapper and forms a triangle shape
3. cut off the unfolded part on the wrapper, or the rectangle leaving a perfect triangle
STEP 3: Folding the Wrappers
1. open the wrapper again and flip it over so that the color side is facing down as shown.
2. take the bottom right corner and fold it along the crease mark made earlier by the triangle.
3. do the same for the top left corner, folding it so that it makes a shape like a kite.
4. taking one if the flaps, fold it in half making a triangle
5. you know its right when the small flaps are inside and invisible. now your ready to assemble!
2. take the bottom right corner and fold it along the crease mark made earlier by the triangle.
3. do the same for the top left corner, folding it so that it makes a shape like a kite.
4. taking one if the flaps, fold it in half making a triangle
5. you know its right when the small flaps are inside and invisible. now your ready to assemble!
STEP 4: Making the Ring
1. measure out a piece of tape about this width and length
2. open up the triangle so that the 2 flaps are showing and place a piece of tape onto the right side of the triangle, sticky side underneath as shown
3. flip over the triangle. to fully secure each triangle, make sure that you have enough tape to attach them all
4. line up the triangle making sure that they don't overlap and that one is not taller than the other
5.flip the piece over, showing the tape
6. take the right side and fold it so it lines up with the tape as shown
7. do the same with the left side
8. press the sides together, showing the inside where the tape is
9. after doing all of them it should look like the last picture on the reverse side
2. open up the triangle so that the 2 flaps are showing and place a piece of tape onto the right side of the triangle, sticky side underneath as shown
3. flip over the triangle. to fully secure each triangle, make sure that you have enough tape to attach them all
4. line up the triangle making sure that they don't overlap and that one is not taller than the other
5.flip the piece over, showing the tape
6. take the right side and fold it so it lines up with the tape as shown
7. do the same with the left side
8. press the sides together, showing the inside where the tape is
9. after doing all of them it should look like the last picture on the reverse side
STEP 5: Adding More
1. to add another triangle, add tape to a single triangle like before, except you are going to attach the new triangle to the group of others on the other side
2. continue until you have added all of the wrappers you wanted
2. continue until you have added all of the wrappers you wanted
STEP 6: Finishing Up
1. once you have added all the wrappers simple connect onto the last open flap on the other wrapper
2. flip it over and TA-DA!
3. attach your artwork to a poster board by tape, glue, or whatever floats your boat
4. if you'd like, try using different wrappers such as starburst, dubble bubble, tootsie roll, or now and later.
Thanks for reading!
like
comment
and post your
creations you've made!
2. flip it over and TA-DA!
3. attach your artwork to a poster board by tape, glue, or whatever floats your boat
4. if you'd like, try using different wrappers such as starburst, dubble bubble, tootsie roll, or now and later.
Thanks for reading!
like
comment
and post your
creations you've made!
4 Comments
dcalve4853 8 years ago
JanieL1 8 years ago
We
are a manufacturer of ribbon bows and trimmings from China, specializing in
making ribbon bows, rosette, packing bows, hair clips, headband, hair loop,
trimmings and various of fancy ribbons etc. They are widely used in the fashion industries, hobby craft, gift wrapping and home
decoration etc.
Please
feel assured that we have more than 10 years of experience in this field. We
offer you not only the most competitive prices but also superior service.
If
you are interested in our products and service, kindly please add our contact
information in your suppliers lists and contact us freely if any inquiry.
Thanks
a lot for your attention and looking forward to being your partner soon.
Sincerely
yours,
Janie Lu
Sales Manager
Midodo
Ribbon Bows & Trimmings Co., Ltd
Tel.: +86-592-8088066 Mobile:
+86-13720881132
Skype:
janie0928
E-mail: midodo@midodoribbons.com
Website: www.midodoribbons.com
Address: Room 916#, No.98 Tapu Road, Siming District, Xiamen City,
Fujian Province, China. Postcode:361008
dcalve4853 8 years ago
MrFixItUpper 8 years ago
I love this, it is so awesome, as soon as I find some colorful wrappers, I am going to try it, we don't have dum dum candy where I live, least not that I know of?