Tell us about yourself!
- laoadam commented on Bnbe_club's instructable IP Camera Display/Monitor Using a Raspberry Pi
- laoadam commented on RonFrtek's instructable Arduino Mosquito RepellentView Instructable »
Does it really work?
- laoadam commented on Imetomi's instructable Ultimate Intelligent Fully Automatic Drone Robot (w/ RPi, Arduino)View Instructable »
Hi, thanks for the nice project.May I use Arduino instead of Raspberry?
- laoadam followed Anton MarkC
- laoadam commented on mviljoen2's instructable How to Analyze a Vehicle's CAN-BUS Using an Arduino Attached to a CAN-BUS Shield and Free Software.View Instructable »
hi, can you tell if can use a MCP2515 can module to replace the CAN-BUS Shield here? Thanks
- laoadam commented on goffrobb's instructable DIY High Current Motor Driver (h-bridge)View Instructable »
Hi goffrobb.1. Did you test the largest current?2. Can the set use the NCP5339MNTXGOSCT-ND? what should change?Thanks
- laoadam commented on HobbyTransform's instructable RC Multi Channel Arduino Proportional Transmitter / Receiver With Button TrimmersView Instructable »
try to test it, didn't get anything from receiver, don't know why?
- laoadam followed TeamJaeger
- laoadam commented on TeamJaeger's instructable Arduino RC GamepadView Instructable »
hi, I am preparing the parts, the attached picture shown a different from yours, may I take the same pin out as yours?
- laoadam commented on dan's instructable Power LED's - Simplest Light With Constant-current CircuitView Instructable »
I made one with IRF3205 and bc337, seems when the input between 10-18, the current keep less changes, say constant. when the input goes low, say 5-9v the current change fast too low.
- laoadam commented on chelseabun's instructable World's Simplest DC Current LimiterView Instructable »
good. can I use a 24v power supply replace the 3v? what should I do?
- laoadam commented on leomiranda's instructable Variable Bench Power Supply
Nice job.can just use a ATX power supply as dc input?
View Instructable »Hi,do you have a video to show the adjusting? I just wonder if the V and I following vary when change either one?
- laoadam followed Surajit Majumdar
- laoadam commented on Surajit Majumdar's instructable DIY Variable Power Supply With Adjustable Voltage and CurrentView Instructable »
Hi, nice job. watched the video, seems when you change the voltage, the current vary meanwhile, and vice versa. can make the V and I vary independently? Thanks
- laoadam commented on ThomasVDD's instructable Variable ATX Bench Powersupply - FabLab EditionView Instructable »
Its great. I checked the lm317, the Maximum output current is 1.5 A, are there any large current IC can do the same work?
- laoadam commented on lacglzh's instructable Build a Robotic Remote ControllerView Instructable »
Hi, do you have a done set of the remote controller.for sale?thanksAdam
- laoadam commented on Mohannad Rawashdeh's instructable Motor Driver BTS7960 43AView Instructable »
Hi Mohannad thanks for your reply, right now I have a 'Nintendo Nunchuk Controller 'like this:https://www.amazon.co.uk/Nintendo-Nunchuk-Controller-Add-On-Wii/dp/B000IMYKQ0If this no work, I can buy whatever working joystick.ThanksAdam
- laoadam commented on Mohannad Rawashdeh's instructable Motor Driver BTS7960 43AView Instructable »
Hi, do you have the detail for how to connect a joystick to it and control the car?ThanksAdam
- laoadam commented on DDelectroTech's instructable how to make a intelligent robotView Instructable »
waiting...
Good job. Can use an Arduino UNO?